4
Travail des métaux et machines-outilsPerceuses et aléseuses
Drilling capacy mild steel: 35 mmSpindle cone: MK 4Distance spindle - column: 300 mmRevs: stufenlos 100 - 2.000 r.p.m.Motor: 3 kWTapping capacity: bis M-33Feeds: 0,10 / 0,20 / 0,30 (3) mm/rmax. drilling depth: 150 mmColumn diameter: 125 mmDistance spindle - table: 90-890 mmDistance spindle-base: 1250 mmTable: 480 x 480 mmLength: 1100 mmWidth: 600 mmHeight: 1950 mmWeight: 360 kg
Drilling capacy mild steel: 35 mm
Spindle cone: MK 4
Distance spindle - column: 300 mm
Revs: stufenlos 100 - 2.000 r.p.m.
Motor: 3 kW
Tapping capacity: bis M-33
Feeds: 0,10 / 0,20 / 0,30 (3) mm/r
max. drilling depth: 150 mm
Column diameter: 125 mm
Distance spindle - table: 90-890 mm
Distance spindle-base: 1250 mm
Table: 480 x 480 mm
Length: 1100 mm
Width: 600 mm
Height: 1950 mm
Weight: 360 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Spindle cone: MK 4
Distance spindle - column: 300 mm
Revs: stufenlos 100 - 2.000 r.p.m.
Motor: 3 kW
Tapping capacity: bis M-33
Feeds: 0,10 / 0,20 / 0,30 (3) mm/r
max. drilling depth: 150 mm
Column diameter: 125 mm
Distance spindle - table: 90-890 mm
Distance spindle-base: 1250 mm
Table: 480 x 480 mm
Length: 1100 mm
Width: 600 mm
Height: 1950 mm
Weight: 360 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
1
Travail des métaux et machines-outilsMachines à travailler la tôlePlieuses
Shaft diameter: 85Rolls diameter: 247 mmDriven rolls: 3Motor power: 7.5 kWFlat steel vertical position (section / min. diameter): 80x20 mm / 500 mm, 30x10 mm / 350 mmFlat steel horizontal position (section / min. diameter): 120x30 mm / 650 mm, 50x10 mm / 300 mmSquare bar (section / min. diameter): 50x50 mm / 500 mm, 30x30 mm / 350 mmRound bar (section / min. diameter): Ø 50 mm / 500 mm, Ø 20 mm / 350 mmTube (section / min. diameter): Ø 100x2,5 mm / 1.300 mm, Ø 20x1 / 300 mmForm tube vertical position (Querschnitt / min. Durchmesser): 80x40x4 mmForm tube square (section / min. diameter): 70x70x4 mmAngle leg outside (Querschnitt / min. Durchmesser): 80x8 mm / 1.200 mm, 30x3 mm / 450 mmAngle leg inside (section / min. diameter): 80x8 mm / 800 mm, 30x3 mm / 450 mmLength: 1580 mmWidth: 1200 mmHeight: 1410 mmWeight: 2350 kg
Shaft diameter: 85
Rolls diameter: 247 mm
Driven rolls: 3
Motor power: 7.5 kW
Flat steel vertical position (section / min. diameter): 80x20 mm / 500 mm, 30x10 mm / 350 mm
Flat steel horizontal position (section / min. diameter): 120x30 mm / 650 mm, 50x10 mm / 300 mm
Square bar (section / min. diameter): 50x50 mm / 500 mm, 30x30 mm / 350 mm
Round bar (section / min. diameter): Ø 50 mm / 500 mm, Ø 20 mm / 350 mm
Tube (section / min. diameter): Ø 100x2,5 mm / 1.300 mm, Ø 20x1 / 300 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 80x40x4 mm
Form tube square (section / min. diameter): 70x70x4 mm
Angle leg outside (Querschnitt / min. Durchmesser): 80x8 mm / 1.200 mm, 30x3 mm / 450 mm
Angle leg inside (section / min. diameter): 80x8 mm / 800 mm, 30x3 mm / 450 mm
Length: 1580 mm
Width: 1200 mm
Height: 1410 mm
Weight: 2350 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Rolls diameter: 247 mm
Driven rolls: 3
Motor power: 7.5 kW
Flat steel vertical position (section / min. diameter): 80x20 mm / 500 mm, 30x10 mm / 350 mm
Flat steel horizontal position (section / min. diameter): 120x30 mm / 650 mm, 50x10 mm / 300 mm
Square bar (section / min. diameter): 50x50 mm / 500 mm, 30x30 mm / 350 mm
Round bar (section / min. diameter): Ø 50 mm / 500 mm, Ø 20 mm / 350 mm
Tube (section / min. diameter): Ø 100x2,5 mm / 1.300 mm, Ø 20x1 / 300 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 80x40x4 mm
Form tube square (section / min. diameter): 70x70x4 mm
Angle leg outside (Querschnitt / min. Durchmesser): 80x8 mm / 1.200 mm, 30x3 mm / 450 mm
Angle leg inside (section / min. diameter): 80x8 mm / 800 mm, 30x3 mm / 450 mm
Length: 1580 mm
Width: 1200 mm
Height: 1410 mm
Weight: 2350 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
1
Travail des métaux et machines-outilsMachines à travailler la tôlePlieuses
Shaft diameter: 120Rolls diameter: 390 mmDriven rolls: 3Motor power: 15 kWSpeed: 2/7,5 m/minFlat steel vertical position (section / min. diameter): 125x25 mm / 1.200 mm, 30x10 mm / 500 mmFlat steel horizontal position (section / min. diameter): 200x50 mm / 1.000 mm, 100x10 mm / 500 mmSquare bar (section / min. diameter): 65x65 mm / 750 mm, 20x20 mm / 500 mmRound bar (section / min. diameter): Ø 80 mm / 850 mm, Ø 20 mm / 500 mmTube (section / min. diameter): Ø 160x4 mm / 2.800 mm, Ø 140x3 mm / 1.500 mm, Ø 50x2 mm / 500 mm, Ø 5"x6,35 / 1.500 mm, Ø 3/4"x2,87 / 500 mmForm tube vertical position (Querschnitt / min. Durchmesser): 120x40x4 mm / 1.800 mm, 30x20x3 mm / 500 mmForm tube square (section / min. diameter): 90x90x5 mm / 1.800 mm, 30x30x3 mm / 500 mmAngle leg outside (Querschnitt / min. Durchmesser): 120x120x12 mm / 1.200 mm, 40x40x4 mm / 600 mmAngle leg inside (section / min. diameter): 100x100x10 mm / 1.200 mm, 40x40x4 mm / 600 mmUPN leg outside (section / min. diameter): UPN 220 / 1.000 mm, UPN 180 / 800 mm, UPN 40 / 500 mmUPN leg inside (section / min. diameter): UPN 220 / 1.200 mm, UPN 180 / 900 mm, UPN 40 / 600 mmIPN horizontal position (section / min. diameter): IPN 220 / 1.000 mm, IPN 80 / 500 mmLength: 2000 mmWidth: 1650 mmHeight: 1900 mmWeight: 4770 kg
Shaft diameter: 120
Rolls diameter: 390 mm
Driven rolls: 3
Motor power: 15 kW
Speed: 2/7,5 m/min
Flat steel vertical position (section / min. diameter): 125x25 mm / 1.200 mm, 30x10 mm / 500 mm
Flat steel horizontal position (section / min. diameter): 200x50 mm / 1.000 mm, 100x10 mm / 500 mm
Square bar (section / min. diameter): 65x65 mm / 750 mm, 20x20 mm / 500 mm
Round bar (section / min. diameter): Ø 80 mm / 850 mm, Ø 20 mm / 500 mm
Tube (section / min. diameter): Ø 160x4 mm / 2.800 mm, Ø 140x3 mm / 1.500 mm, Ø 50x2 mm / 500 mm, Ø 5"x6,35 / 1.500 mm, Ø 3/4"x2,87 / 500 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 120x40x4 mm / 1.800 mm, 30x20x3 mm / 500 mm
Form tube square (section / min. diameter): 90x90x5 mm / 1.800 mm, 30x30x3 mm / 500 mm
Angle leg outside (Querschnitt / min. Durchmesser): 120x120x12 mm / 1.200 mm, 40x40x4 mm / 600 mm
Angle leg inside (section / min. diameter): 100x100x10 mm / 1.200 mm, 40x40x4 mm / 600 mm
UPN leg outside (section / min. diameter): UPN 220 / 1.000 mm, UPN 180 / 800 mm, UPN 40 / 500 mm
UPN leg inside (section / min. diameter): UPN 220 / 1.200 mm, UPN 180 / 900 mm, UPN 40 / 600 mm
IPN horizontal position (section / min. diameter): IPN 220 / 1.000 mm, IPN 80 / 500 mm
Length: 2000 mm
Width: 1650 mm
Height: 1900 mm
Weight: 4770 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Rolls diameter: 390 mm
Driven rolls: 3
Motor power: 15 kW
Speed: 2/7,5 m/min
Flat steel vertical position (section / min. diameter): 125x25 mm / 1.200 mm, 30x10 mm / 500 mm
Flat steel horizontal position (section / min. diameter): 200x50 mm / 1.000 mm, 100x10 mm / 500 mm
Square bar (section / min. diameter): 65x65 mm / 750 mm, 20x20 mm / 500 mm
Round bar (section / min. diameter): Ø 80 mm / 850 mm, Ø 20 mm / 500 mm
Tube (section / min. diameter): Ø 160x4 mm / 2.800 mm, Ø 140x3 mm / 1.500 mm, Ø 50x2 mm / 500 mm, Ø 5"x6,35 / 1.500 mm, Ø 3/4"x2,87 / 500 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 120x40x4 mm / 1.800 mm, 30x20x3 mm / 500 mm
Form tube square (section / min. diameter): 90x90x5 mm / 1.800 mm, 30x30x3 mm / 500 mm
Angle leg outside (Querschnitt / min. Durchmesser): 120x120x12 mm / 1.200 mm, 40x40x4 mm / 600 mm
Angle leg inside (section / min. diameter): 100x100x10 mm / 1.200 mm, 40x40x4 mm / 600 mm
UPN leg outside (section / min. diameter): UPN 220 / 1.000 mm, UPN 180 / 800 mm, UPN 40 / 500 mm
UPN leg inside (section / min. diameter): UPN 220 / 1.200 mm, UPN 180 / 900 mm, UPN 40 / 600 mm
IPN horizontal position (section / min. diameter): IPN 220 / 1.000 mm, IPN 80 / 500 mm
Length: 2000 mm
Width: 1650 mm
Height: 1900 mm
Weight: 4770 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
1
Travail des métaux et machines-outilsMachines à travailler la tôleFreins de presse
pressing capacity: 40 toBending length: 2050 mmAxes: Y1 / Y2 / X and R axisStroke: 200 mmInside distance between side frames: 1700 mmGap in side frame: 350 mmDaylight: 440 mmPower concept: servomotorized spindle driverapid speed Y-axis: 180 mm/sWorking speed Y-axis: 10Retractionspeed Y-axis: 115Back gauge travel X-axis: 650 mmBack gauge travel R-axis: 250 mmTable height: 900 mmMotor power: 7.2 kWLength: 2600 mmWidth: 1450 mmHeight: 2650 mmWeight: 4400 kg
pressing capacity: 40 to
Bending length: 2050 mm
Axes: Y1 / Y2 / X and R axis
Stroke: 200 mm
Inside distance between side frames: 1700 mm
Gap in side frame: 350 mm
Daylight: 440 mm
Power concept: servomotorized spindle drive
rapid speed Y-axis: 180 mm/s
Working speed Y-axis: 10
Retractionspeed Y-axis: 115
Back gauge travel X-axis: 650 mm
Back gauge travel R-axis: 250 mm
Table height: 900 mm
Motor power: 7.2 kW
Length: 2600 mm
Width: 1450 mm
Height: 2650 mm
Weight: 4400 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Bending length: 2050 mm
Axes: Y1 / Y2 / X and R axis
Stroke: 200 mm
Inside distance between side frames: 1700 mm
Gap in side frame: 350 mm
Daylight: 440 mm
Power concept: servomotorized spindle drive
rapid speed Y-axis: 180 mm/s
Working speed Y-axis: 10
Retractionspeed Y-axis: 115
Back gauge travel X-axis: 650 mm
Back gauge travel R-axis: 250 mm
Table height: 900 mm
Motor power: 7.2 kW
Length: 2600 mm
Width: 1450 mm
Height: 2650 mm
Weight: 4400 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
1
Travail des métaux et machines-outilsMachines à travailler la tôleFreins de presse
pressing capacity: 40 toBending length: 1250 mmAxes: Y1 / Y2 / X and R axisStroke: 200 mmInside distance between side frames: 1050 mmGap in side frame: 250 mmDaylight: 440 mmPower concept: servomotorized spindle driverapid speed Y-axis: 115 mm/sWorking speed Y-axis: 10Retractionspeed Y-axis: 115Back gauge travel X-axis: 650 mmBack gauge travel R-axis: 250 mmTable height: 1000 mmMotor power: 7.2 kWLength: 1950 mmWidth: 1450 mmHeight: 2650 mmWeight: 3600 kg
pressing capacity: 40 to
Bending length: 1250 mm
Axes: Y1 / Y2 / X and R axis
Stroke: 200 mm
Inside distance between side frames: 1050 mm
Gap in side frame: 250 mm
Daylight: 440 mm
Power concept: servomotorized spindle drive
rapid speed Y-axis: 115 mm/s
Working speed Y-axis: 10
Retractionspeed Y-axis: 115
Back gauge travel X-axis: 650 mm
Back gauge travel R-axis: 250 mm
Table height: 1000 mm
Motor power: 7.2 kW
Length: 1950 mm
Width: 1450 mm
Height: 2650 mm
Weight: 3600 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Bending length: 1250 mm
Axes: Y1 / Y2 / X and R axis
Stroke: 200 mm
Inside distance between side frames: 1050 mm
Gap in side frame: 250 mm
Daylight: 440 mm
Power concept: servomotorized spindle drive
rapid speed Y-axis: 115 mm/s
Working speed Y-axis: 10
Retractionspeed Y-axis: 115
Back gauge travel X-axis: 650 mm
Back gauge travel R-axis: 250 mm
Table height: 1000 mm
Motor power: 7.2 kW
Length: 1950 mm
Width: 1450 mm
Height: 2650 mm
Weight: 3600 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
4
Travail des métaux et machines-outilsMachines à travailler la tôleFreins de presse
pressing capacity: 320 toBending length: 4050 mmAxes: Y1 / Y2 / X and R axisStroke: 365 mmInside distance between side frames: 3600 mmGap in side frame: 410 mmDaylight: 630 mmPower concept: hydraulicrapid speed Y-axis: 160 mm/sWorking speed Y-axis: 10Retractionspeed Y-axis: 160Back gauge travel X-axis: 650 mmBack gauge speed X-axis: 500Back gauge travel R-axis: 250 mmTable height: 900 mmTable width: 154 mmMotor power: 2 x 11 kWLength: 5300 mmWidth: 1910 mmHeight: 3230 mmWeight: 20100 kg
pressing capacity: 320 to
Bending length: 4050 mm
Axes: Y1 / Y2 / X and R axis
Stroke: 365 mm
Inside distance between side frames: 3600 mm
Gap in side frame: 410 mm
Daylight: 630 mm
Power concept: hydraulic
rapid speed Y-axis: 160 mm/s
Working speed Y-axis: 10
Retractionspeed Y-axis: 160
Back gauge travel X-axis: 650 mm
Back gauge speed X-axis: 500
Back gauge travel R-axis: 250 mm
Table height: 900 mm
Table width: 154 mm
Motor power: 2 x 11 kW
Length: 5300 mm
Width: 1910 mm
Height: 3230 mm
Weight: 20100 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Bending length: 4050 mm
Axes: Y1 / Y2 / X and R axis
Stroke: 365 mm
Inside distance between side frames: 3600 mm
Gap in side frame: 410 mm
Daylight: 630 mm
Power concept: hydraulic
rapid speed Y-axis: 160 mm/s
Working speed Y-axis: 10
Retractionspeed Y-axis: 160
Back gauge travel X-axis: 650 mm
Back gauge speed X-axis: 500
Back gauge travel R-axis: 250 mm
Table height: 900 mm
Table width: 154 mm
Motor power: 2 x 11 kW
Length: 5300 mm
Width: 1910 mm
Height: 3230 mm
Weight: 20100 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
4
Travail des métaux et machines-outilsMachines à travailler la tôleFreins de presse
pressing capacity: 320 toBending length: 3050 mmAxes: Y1 / Y2 / X and R axisStroke: 365 mmInside distance between side frames: 2600 mmGap in side frame: 410 mmDaylight: 630 mmPower concept: hydraulicrapid speed Y-axis: 160 mm/sWorking speed Y-axis: 10Retractionspeed Y-axis: 160Back gauge travel X-axis: 650 mmBack gauge speed X-axis: 500Back gauge travel R-axis: 250 mmTable height: 900 mmTable width: 104 mmMotor power: 2 x 11 kWLength: 4300 mmWidth: 1820 mmHeight: 3330 mmWeight: 16500 kg
pressing capacity: 320 to
Bending length: 3050 mm
Axes: Y1 / Y2 / X and R axis
Stroke: 365 mm
Inside distance between side frames: 2600 mm
Gap in side frame: 410 mm
Daylight: 630 mm
Power concept: hydraulic
rapid speed Y-axis: 160 mm/s
Working speed Y-axis: 10
Retractionspeed Y-axis: 160
Back gauge travel X-axis: 650 mm
Back gauge speed X-axis: 500
Back gauge travel R-axis: 250 mm
Table height: 900 mm
Table width: 104 mm
Motor power: 2 x 11 kW
Length: 4300 mm
Width: 1820 mm
Height: 3330 mm
Weight: 16500 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Bending length: 3050 mm
Axes: Y1 / Y2 / X and R axis
Stroke: 365 mm
Inside distance between side frames: 2600 mm
Gap in side frame: 410 mm
Daylight: 630 mm
Power concept: hydraulic
rapid speed Y-axis: 160 mm/s
Working speed Y-axis: 10
Retractionspeed Y-axis: 160
Back gauge travel X-axis: 650 mm
Back gauge speed X-axis: 500
Back gauge travel R-axis: 250 mm
Table height: 900 mm
Table width: 104 mm
Motor power: 2 x 11 kW
Length: 4300 mm
Width: 1820 mm
Height: 3330 mm
Weight: 16500 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
1
Travail des métaux et machines-outilsMachines à travailler la tôlePlieuses pivotantes
Bending length: 3100 mmSheet thickness (420 N/mm²): 3.5 mmAntrieb: HydraulicMax. bending angle: 135 °Length: 4300 mmWidth: 1770 mmHeight: 1890 mmWeight: 4220 kg
Bending length: 3100 mm
Sheet thickness (420 N/mm²): 3.5 mm
Antrieb: Hydraulic
Max. bending angle: 135 °
Length: 4300 mm
Width: 1770 mm
Height: 1890 mm
Weight: 4220 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Sheet thickness (420 N/mm²): 3.5 mm
Antrieb: Hydraulic
Max. bending angle: 135 °
Length: 4300 mm
Width: 1770 mm
Height: 1890 mm
Weight: 4220 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
1
Travail des métaux et machines-outilsMachines à travailler la tôlePerforation
Punching power: 80 tonThroat depth: 750 mmMax. diameter at sheet thickness (mild steel): 40x14 mmMax. number of strokes at 20 mm stroke: 40 1/minMotor: 9 kWLength: 1700 mmWidth: 1300 mmHeight: 2050 mmWeight: 1715 kg
Punching power: 80 ton
Throat depth: 750 mm
Max. diameter at sheet thickness (mild steel): 40x14 mm
Max. number of strokes at 20 mm stroke: 40 1/min
Motor: 9 kW
Length: 1700 mm
Width: 1300 mm
Height: 2050 mm
Weight: 1715 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Throat depth: 750 mm
Max. diameter at sheet thickness (mild steel): 40x14 mm
Max. number of strokes at 20 mm stroke: 40 1/min
Motor: 9 kW
Length: 1700 mm
Width: 1300 mm
Height: 2050 mm
Weight: 1715 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
2
Travail des métaux et machines-outilsTours
Swing over bed: 500 mmDistance between centers: 1500 mmCentre height: 250 mmSpindle bore: 75 mmswing over cross slide: 300 mmWidth of bed: 400 mmSpindle nose / DIN55027: 8Spindle taper: 80 MRevs continuous variable in gear steps: 3Revs continuous variable: 25-100, 100-400, 500-2000 rpmNumber of feeds: 120Longitudinal feed range: 0.04 - 12 mm/rCross feed range: 0.02 - 6 mm/rMetric thread range: 0.5 - 120 mmInch thread range: Array TpiModule thread range: 0.125 - 30DP thread range: 1 - 240Cross slide travel: 315 mmTop slide travel: 130 mmTailstock quill diameter: 90 mmTailstock quill taper: 5 MKTailstock travel: 230 mmMotor power: 11 kWWeight: 2950 kg
Swing over bed: 500 mm
Distance between centers: 1500 mm
Centre height: 250 mm
Spindle bore: 75 mm
swing over cross slide: 300 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 8
Spindle taper: 80 M
Revs continuous variable in gear steps: 3
Revs continuous variable: 25-100, 100-400, 500-2000 rpm
Number of feeds: 120
Longitudinal feed range: 0.04 - 12 mm/r
Cross feed range: 0.02 - 6 mm/r
Metric thread range: 0.5 - 120 mm
Inch thread range: Array Tpi
Module thread range: 0.125 - 30
DP thread range: 1 - 240
Cross slide travel: 315 mm
Top slide travel: 130 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 230 mm
Motor power: 11 kW
Weight: 2950 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Distance between centers: 1500 mm
Centre height: 250 mm
Spindle bore: 75 mm
swing over cross slide: 300 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 8
Spindle taper: 80 M
Revs continuous variable in gear steps: 3
Revs continuous variable: 25-100, 100-400, 500-2000 rpm
Number of feeds: 120
Longitudinal feed range: 0.04 - 12 mm/r
Cross feed range: 0.02 - 6 mm/r
Metric thread range: 0.5 - 120 mm
Inch thread range: Array Tpi
Module thread range: 0.125 - 30
DP thread range: 1 - 240
Cross slide travel: 315 mm
Top slide travel: 130 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 230 mm
Motor power: 11 kW
Weight: 2950 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
2
Travail des métaux et machines-outilsTours
Swing over bed: 400 mmDistance between centers: 750 mmCentre height: 165 mmSpindle bore: 32 mmswing over cross slide: 190 mmWidth of bed: 200 mmSpindle nose / DIN55027: 5Spindle taper: 4 MRevs continuous variable in gear steps: 2Revs continuous variable: 85-405, 470-2200 rpmNumber of feeds: 48Longitudinal feed range: 0.006 - 1.77 mm/rCross feed range: 0.003 - 0.885 mm/rMetric thread range: 0.1 - 28 mmInch thread range: Array TpiModule thread range: 0.1 - 1.75DP thread range: 4 - 70Cross slide travel: 150 mmTop slide travel: 95 mmTailstock quill diameter: 40 mmTailstock quill taper: 3 MKTailstock travel: 100 mmMotor power: 2.2 kWWeight: 770 kg
Swing over bed: 400 mm
Distance between centers: 750 mm
Centre height: 165 mm
Spindle bore: 32 mm
swing over cross slide: 190 mm
Width of bed: 200 mm
Spindle nose / DIN55027: 5
Spindle taper: 4 M
Revs continuous variable in gear steps: 2
Revs continuous variable: 85-405, 470-2200 rpm
Number of feeds: 48
Longitudinal feed range: 0.006 - 1.77 mm/r
Cross feed range: 0.003 - 0.885 mm/r
Metric thread range: 0.1 - 28 mm
Inch thread range: Array Tpi
Module thread range: 0.1 - 1.75
DP thread range: 4 - 70
Cross slide travel: 150 mm
Top slide travel: 95 mm
Tailstock quill diameter: 40 mm
Tailstock quill taper: 3 MK
Tailstock travel: 100 mm
Motor power: 2.2 kW
Weight: 770 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Distance between centers: 750 mm
Centre height: 165 mm
Spindle bore: 32 mm
swing over cross slide: 190 mm
Width of bed: 200 mm
Spindle nose / DIN55027: 5
Spindle taper: 4 M
Revs continuous variable in gear steps: 2
Revs continuous variable: 85-405, 470-2200 rpm
Number of feeds: 48
Longitudinal feed range: 0.006 - 1.77 mm/r
Cross feed range: 0.003 - 0.885 mm/r
Metric thread range: 0.1 - 28 mm
Inch thread range: Array Tpi
Module thread range: 0.1 - 1.75
DP thread range: 4 - 70
Cross slide travel: 150 mm
Top slide travel: 95 mm
Tailstock quill diameter: 40 mm
Tailstock quill taper: 3 MK
Tailstock travel: 100 mm
Motor power: 2.2 kW
Weight: 770 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
1
Travail des métaux et machines-outilsMachines à travailler la tôleCisailles à section en acier
Punching power: 165 tonThroat depth: 610 mmNumber of stations: 5Max. diameter at sheet thickness (mild steel): 40/30 bzw. 34/34 mmStroke: 110 mmStrokes: 31 1/minFlat steel: 750x20 / 400x30 mmAngle steel: 205x205x18 mmRound / square steel: 60 mmNotcher: 16x58x110 mmMotor: 15 kWLength: 2950 mmWidth: 1600 mmHeight: 2200 mmWeight: 6300 kg
Punching power: 165 ton
Throat depth: 610 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/30 bzw. 34/34 mm
Stroke: 110 mm
Strokes: 31 1/min
Flat steel: 750x20 / 400x30 mm
Angle steel: 205x205x18 mm
Round / square steel: 60 mm
Notcher: 16x58x110 mm
Motor: 15 kW
Length: 2950 mm
Width: 1600 mm
Height: 2200 mm
Weight: 6300 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Throat depth: 610 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/30 bzw. 34/34 mm
Stroke: 110 mm
Strokes: 31 1/min
Flat steel: 750x20 / 400x30 mm
Angle steel: 205x205x18 mm
Round / square steel: 60 mm
Notcher: 16x58x110 mm
Motor: 15 kW
Length: 2950 mm
Width: 1600 mm
Height: 2200 mm
Weight: 6300 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
1
Travail des métaux et machines-outilsPerceuses et aléseuses
Drilling capacy mild steel: 32 mmSpindle cone: MK 3Distance spindle - column: 250 mmRevs: 65 - 125 - 185 - 365 - 540 - 1.055 - 1.560 - 3.060 r.p.m.Tapping capacity: M24Column diameter: 100 mmDistance spindle - table: 85 - 635 mmDistance spindle-base: 1.17 mmTable: 300 x 270 mmBase dimensions: 600 x 380 mmQuill travel: 120 mmLength: 600 mmWidth: 640 mmHeight: 2020 mmWeight: 260 kg
Drilling capacy mild steel: 32 mm
Spindle cone: MK 3
Distance spindle - column: 250 mm
Revs: 65 - 125 - 185 - 365 - 540 - 1.055 - 1.560 - 3.060 r.p.m.
Tapping capacity: M24
Column diameter: 100 mm
Distance spindle - table: 85 - 635 mm
Distance spindle-base: 1.17 mm
Table: 300 x 270 mm
Base dimensions: 600 x 380 mm
Quill travel: 120 mm
Length: 600 mm
Width: 640 mm
Height: 2020 mm
Weight: 260 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Spindle cone: MK 3
Distance spindle - column: 250 mm
Revs: 65 - 125 - 185 - 365 - 540 - 1.055 - 1.560 - 3.060 r.p.m.
Tapping capacity: M24
Column diameter: 100 mm
Distance spindle - table: 85 - 635 mm
Distance spindle-base: 1.17 mm
Table: 300 x 270 mm
Base dimensions: 600 x 380 mm
Quill travel: 120 mm
Length: 600 mm
Width: 640 mm
Height: 2020 mm
Weight: 260 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
6
Travail des métaux et machines-outilsMachines à travailler la tôlePlieuses pivotantes
Bending length: 8020 mmBending capacity steel 400 N/mm²: 1.5 mmBending capacity Alu 190 N/mm²: 2 mmNo. of stand and tension arm units: 8
Bending length: 8020 mm
Bending capacity steel 400 N/mm²: 1.5 mm
Bending capacity Alu 190 N/mm²: 2 mm
No. of stand and tension arm units: 8
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Bending capacity steel 400 N/mm²: 1.5 mm
Bending capacity Alu 190 N/mm²: 2 mm
No. of stand and tension arm units: 8
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
6
Travail des métaux et machines-outilsMachines à travailler la tôlePlieuses pivotantes
Bending length: 8200 mmBending capacity steel 400 N/mm²: 2 mmBending capacity Alu 190 N/mm²: 2 mmCutting capacity electrical shear: 1.5 - 2 mmNo. of stand and tension arm units: 8No. of driven linkage assemblies: 8Sheet insertion depth: 1000 mm
Bending length: 8200 mm
Bending capacity steel 400 N/mm²: 2 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.5 - 2 mm
No. of stand and tension arm units: 8
No. of driven linkage assemblies: 8
Sheet insertion depth: 1000 mm
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Bending capacity steel 400 N/mm²: 2 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.5 - 2 mm
No. of stand and tension arm units: 8
No. of driven linkage assemblies: 8
Sheet insertion depth: 1000 mm
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
6
Travail des métaux et machines-outilsMachines à travailler la tôlePlieuses pivotantes
Bending length: 6400 mmBending capacity steel 400 N/mm²: 1.75 mmBending capacity Alu 190 N/mm²: 2 mmNo. of stand and tension arm units: 6Sheet insertion depth: 1000 mm
Bending length: 6400 mm
Bending capacity steel 400 N/mm²: 1.75 mm
Bending capacity Alu 190 N/mm²: 2 mm
No. of stand and tension arm units: 6
Sheet insertion depth: 1000 mm
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Bending capacity steel 400 N/mm²: 1.75 mm
Bending capacity Alu 190 N/mm²: 2 mm
No. of stand and tension arm units: 6
Sheet insertion depth: 1000 mm
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
5
Travail des métaux et machines-outilsMachines à travailler la tôleFreins de presse
pressing capacity: 40 toBending length: 1250 mmAxes: X and Y axisStroke: 100 mmDaylight: 310 mmPower concept: hydraulicOiltank: 38 lMotor: 6 kWBack gauge: 420 mmDie: 1Geschwindigkeit: 10 mm/sRetraction speed: 12 mm/sBack gauge speed: 40 mm/sAccuracy press beam: 0.02 +/- mmBack gauge accuracy: 0.05 +/- mmLength: 1750 mmWidth: 950 mmHeight: 1900 mmWeight: 1640 kg
pressing capacity: 40 to
Bending length: 1250 mm
Axes: X and Y axis
Stroke: 100 mm
Daylight: 310 mm
Power concept: hydraulic
Oiltank: 38 l
Motor: 6 kW
Back gauge: 420 mm
Die: 1
Geschwindigkeit: 10 mm/s
Retraction speed: 12 mm/s
Back gauge speed: 40 mm/s
Accuracy press beam: 0.02 +/- mm
Back gauge accuracy: 0.05 +/- mm
Length: 1750 mm
Width: 950 mm
Height: 1900 mm
Weight: 1640 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Bending length: 1250 mm
Axes: X and Y axis
Stroke: 100 mm
Daylight: 310 mm
Power concept: hydraulic
Oiltank: 38 l
Motor: 6 kW
Back gauge: 420 mm
Die: 1
Geschwindigkeit: 10 mm/s
Retraction speed: 12 mm/s
Back gauge speed: 40 mm/s
Accuracy press beam: 0.02 +/- mm
Back gauge accuracy: 0.05 +/- mm
Length: 1750 mm
Width: 950 mm
Height: 1900 mm
Weight: 1640 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
1
Travail des métaux et machines-outilsSciageScies circulaires
Saw blade diameter: 300 mmSaw blade dimensions: 300 x (2)2,5 x 32 mmSaw blade speed: Array rpmMitre left: 45 °Mitre right: 45 °Cutting capacity 0°: rund 102 mm, Quadratprofil 90 mm, Rechteckprofil 120 x 80 mmCutting capacity 45° right: rund 90 mm, Quadratprofil 80 mm, Rechteckprofil 90 x 70 mmCutting capacity 45° left: rund 80 mm, Quadratprofil 70 mm, Rechteckprofil 85 x 70 mmMotor: 1,5/2 kWWidth: 500 mmDepth: 1050 mmHeight: 990 mmWeight: 135 kg
Saw blade diameter: 300 mm
Saw blade dimensions: 300 x (2)2,5 x 32 mm
Saw blade speed: Array rpm
Mitre left: 45 °
Mitre right: 45 °
Cutting capacity 0°: rund 102 mm, Quadratprofil 90 mm, Rechteckprofil 120 x 80 mm
Cutting capacity 45° right: rund 90 mm, Quadratprofil 80 mm, Rechteckprofil 90 x 70 mm
Cutting capacity 45° left: rund 80 mm, Quadratprofil 70 mm, Rechteckprofil 85 x 70 mm
Motor: 1,5/2 kW
Width: 500 mm
Depth: 1050 mm
Height: 990 mm
Weight: 135 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Saw blade dimensions: 300 x (2)2,5 x 32 mm
Saw blade speed: Array rpm
Mitre left: 45 °
Mitre right: 45 °
Cutting capacity 0°: rund 102 mm, Quadratprofil 90 mm, Rechteckprofil 120 x 80 mm
Cutting capacity 45° right: rund 90 mm, Quadratprofil 80 mm, Rechteckprofil 90 x 70 mm
Cutting capacity 45° left: rund 80 mm, Quadratprofil 70 mm, Rechteckprofil 85 x 70 mm
Motor: 1,5/2 kW
Width: 500 mm
Depth: 1050 mm
Height: 990 mm
Weight: 135 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
1
Travail des métaux et machines-outilsPressesPresses excentriques
pressing capacity: 110 toTable length: 900 mmTable width: 540 mmHole in table: 180 mmStroke: 14 - 114 mmStrokes: 60 1/minRam: 490x325 mmRam adjustment: 90 mmThroat depth: 280 mmMotor: 7.5 kWLength: 1870 mmWidth: 1320 mmHeight: 2800 mmWeight: 5600 kg
pressing capacity: 110 to
Table length: 900 mm
Table width: 540 mm
Hole in table: 180 mm
Stroke: 14 - 114 mm
Strokes: 60 1/min
Ram: 490x325 mm
Ram adjustment: 90 mm
Throat depth: 280 mm
Motor: 7.5 kW
Length: 1870 mm
Width: 1320 mm
Height: 2800 mm
Weight: 5600 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Table length: 900 mm
Table width: 540 mm
Hole in table: 180 mm
Stroke: 14 - 114 mm
Strokes: 60 1/min
Ram: 490x325 mm
Ram adjustment: 90 mm
Throat depth: 280 mm
Motor: 7.5 kW
Length: 1870 mm
Width: 1320 mm
Height: 2800 mm
Weight: 5600 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
1
Travail des métaux et machines-outilsMachines à travailler la tôleCisailles à section en acier
Punching power: 45 tonThroat depth: 175 mmNumber of stations: 4Max. diameter at sheet thickness (mild steel): 27 x 12 mmStroke: 15 mmStrokes: 16 1/minFlat steel: 300x10 / 200x13 mmAngle steel: 80x80x8 mmNotcher: 7 mmMotor: 2 kWLength: 1360 mmWidth: 1100 mmHeight: 1500 mmWeight: 800 kg
Punching power: 45 ton
Throat depth: 175 mm
Number of stations: 4
Max. diameter at sheet thickness (mild steel): 27 x 12 mm
Stroke: 15 mm
Strokes: 16 1/min
Flat steel: 300x10 / 200x13 mm
Angle steel: 80x80x8 mm
Notcher: 7 mm
Motor: 2 kW
Length: 1360 mm
Width: 1100 mm
Height: 1500 mm
Weight: 800 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Throat depth: 175 mm
Number of stations: 4
Max. diameter at sheet thickness (mild steel): 27 x 12 mm
Stroke: 15 mm
Strokes: 16 1/min
Flat steel: 300x10 / 200x13 mm
Angle steel: 80x80x8 mm
Notcher: 7 mm
Motor: 2 kW
Length: 1360 mm
Width: 1100 mm
Height: 1500 mm
Weight: 800 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
2
Travail des métaux et machines-outilsSciageScies à courroies
Saw frame: Double columnBand dimensions: 6800x41x1,3 mmBand speed continous: 20-100 m/minCutting capacity 0° round: 560 mmCutting capacity 0° square: 540 mmCutting capacity 0° rectangular: 820x540 mmCutting capacity 45°: rund 550 mm, quadrat 540 mm, rechteck 550 x 540 mmCutting capacity 60°: rund 360 mm, quadrat 360 mm, rechteck 360 x 540 mmCutting capacity - 45°: rund 550 mm, quadrat 540 mm, rechteck 550 x 540 mmWorking height: 880 mmCoolant pump motor: 0.12 kWHydraulic motor: 0.37 kWMotor: 4 kWLength: 3800 mmWidth: 1750 mmHeight: 2350 mmWeight: 3200 kg
Saw frame: Double column
Band dimensions: 6800x41x1,3 mm
Band speed continous: 20-100 m/min
Cutting capacity 0° round: 560 mm
Cutting capacity 0° square: 540 mm
Cutting capacity 0° rectangular: 820x540 mm
Cutting capacity 45°: rund 550 mm, quadrat 540 mm, rechteck 550 x 540 mm
Cutting capacity 60°: rund 360 mm, quadrat 360 mm, rechteck 360 x 540 mm
Cutting capacity - 45°: rund 550 mm, quadrat 540 mm, rechteck 550 x 540 mm
Working height: 880 mm
Coolant pump motor: 0.12 kW
Hydraulic motor: 0.37 kW
Motor: 4 kW
Length: 3800 mm
Width: 1750 mm
Height: 2350 mm
Weight: 3200 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Band dimensions: 6800x41x1,3 mm
Band speed continous: 20-100 m/min
Cutting capacity 0° round: 560 mm
Cutting capacity 0° square: 540 mm
Cutting capacity 0° rectangular: 820x540 mm
Cutting capacity 45°: rund 550 mm, quadrat 540 mm, rechteck 550 x 540 mm
Cutting capacity 60°: rund 360 mm, quadrat 360 mm, rechteck 360 x 540 mm
Cutting capacity - 45°: rund 550 mm, quadrat 540 mm, rechteck 550 x 540 mm
Working height: 880 mm
Coolant pump motor: 0.12 kW
Hydraulic motor: 0.37 kW
Motor: 4 kW
Length: 3800 mm
Width: 1750 mm
Height: 2350 mm
Weight: 3200 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
2
Travail des métaux et machines-outilsMachines à travailler la tôleCisaille pour tôle
Cutting length: 2050 mmMax. thickness - mild steel: 4 mmStrokes: 42 1/minBack gauge: 750 mmMotor power: 7.5 kWTable height: 800 mmTable width: 450 mmLength: 2700 mmWidth: 2300 mmHeight: 1350 mmWeight: 2800 kg
Cutting length: 2050 mm
Max. thickness - mild steel: 4 mm
Strokes: 42 1/min
Back gauge: 750 mm
Motor power: 7.5 kW
Table height: 800 mm
Table width: 450 mm
Length: 2700 mm
Width: 2300 mm
Height: 1350 mm
Weight: 2800 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Max. thickness - mild steel: 4 mm
Strokes: 42 1/min
Back gauge: 750 mm
Motor power: 7.5 kW
Table height: 800 mm
Table width: 450 mm
Length: 2700 mm
Width: 2300 mm
Height: 1350 mm
Weight: 2800 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
1
Travail des métaux et machines-outilsMachines à travailler la tôlePerforation
Punching power: 110 tonThroat depth: 500 mmMax. diameter at sheet thickness (mild steel): 40x20 mmMax. number of strokes at 20 mm stroke: 28 1/minMotor: 9 kWLength: 2080 mmWidth: 1300 mmHeight: 2050 mmWeight: 3150 kg
Punching power: 110 ton
Throat depth: 500 mm
Max. diameter at sheet thickness (mild steel): 40x20 mm
Max. number of strokes at 20 mm stroke: 28 1/min
Motor: 9 kW
Length: 2080 mm
Width: 1300 mm
Height: 2050 mm
Weight: 3150 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Throat depth: 500 mm
Max. diameter at sheet thickness (mild steel): 40x20 mm
Max. number of strokes at 20 mm stroke: 28 1/min
Motor: 9 kW
Length: 2080 mm
Width: 1300 mm
Height: 2050 mm
Weight: 3150 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
2
Travail des métaux et machines-outilsPonceuses
Distance spindle - table: 730 mmTable: 1200 x 600 mmGrinding lenght: 1200 mmMagnetic table: 1200 x 600 mmTable movement hydraulic: 1300 mmTable speed: 5 - 30 m/minCross feed rapid travel: 0-2250 m/minAutomatic cross feed incremental: 0,001-32 mmMax. cross feed: 685 mmAutomatic vertical feed: 560 mmRapid vertical feed approx.: 0-675 mm/minSpindle revs: 500-2200 rpmSpindle motor: 11 kWHydraulic motor: 5.5 kWCross feed motor: 3.1 kWFeed motor grinding wheel: 3.1 kWMax. workpiece weight on magnetic table: 1150 kgMax. workpiece weight on t-slot table: 1600 kgGrinding wheel dimensions: 405 x 75 x 127 mmAutomatic elevating movement: 0,001 - 0,04 mmLength: 4790 mmWidth: 3207 mmHeight: 2305 mmWeight: 8100 kg
Distance spindle - table: 730 mm
Table: 1200 x 600 mm
Grinding lenght: 1200 mm
Magnetic table: 1200 x 600 mm
Table movement hydraulic: 1300 mm
Table speed: 5 - 30 m/min
Cross feed rapid travel: 0-2250 m/min
Automatic cross feed incremental: 0,001-32 mm
Max. cross feed: 685 mm
Automatic vertical feed: 560 mm
Rapid vertical feed approx.: 0-675 mm/min
Spindle revs: 500-2200 rpm
Spindle motor: 11 kW
Hydraulic motor: 5.5 kW
Cross feed motor: 3.1 kW
Feed motor grinding wheel: 3.1 kW
Max. workpiece weight on magnetic table: 1150 kg
Max. workpiece weight on t-slot table: 1600 kg
Grinding wheel dimensions: 405 x 75 x 127 mm
Automatic elevating movement: 0,001 - 0,04 mm
Length: 4790 mm
Width: 3207 mm
Height: 2305 mm
Weight: 8100 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Table: 1200 x 600 mm
Grinding lenght: 1200 mm
Magnetic table: 1200 x 600 mm
Table movement hydraulic: 1300 mm
Table speed: 5 - 30 m/min
Cross feed rapid travel: 0-2250 m/min
Automatic cross feed incremental: 0,001-32 mm
Max. cross feed: 685 mm
Automatic vertical feed: 560 mm
Rapid vertical feed approx.: 0-675 mm/min
Spindle revs: 500-2200 rpm
Spindle motor: 11 kW
Hydraulic motor: 5.5 kW
Cross feed motor: 3.1 kW
Feed motor grinding wheel: 3.1 kW
Max. workpiece weight on magnetic table: 1150 kg
Max. workpiece weight on t-slot table: 1600 kg
Grinding wheel dimensions: 405 x 75 x 127 mm
Automatic elevating movement: 0,001 - 0,04 mm
Length: 4790 mm
Width: 3207 mm
Height: 2305 mm
Weight: 8100 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
2
Travail des métaux et machines-outilsTours
Swing over bed: 630 mmDistance between centers: 2000 mmCentre height: 315 mmSpindle bore: 103 mmswing over cross slide: 430 mmWidth of bed: 400 mmSpindle nose / DIN55027: 11Spindle taper: 120 MSpindle speed steps: 21Spindle revs: Array rpmNumber of feeds: 120Longitudinal feed range: 0.04 - 12 mm/rCross feed range: 0.02 - 6 mm/rMetric thread range: 0.5 - 120 mmInch thread range: 60 - 1/4 TpiModule thread range: 0.125 - 30DP thread range: ArrayCross slide travel: 315 mmTop slide travel: 90 mmTailstock quill diameter: 90 mmTailstock quill taper: 5 MKTailstock travel: 230 mmMotor power: 11 kWWeight: 3310 kg
Swing over bed: 630 mm
Distance between centers: 2000 mm
Centre height: 315 mm
Spindle bore: 103 mm
swing over cross slide: 430 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 11
Spindle taper: 120 M
Spindle speed steps: 21
Spindle revs: Array rpm
Number of feeds: 120
Longitudinal feed range: 0.04 - 12 mm/r
Cross feed range: 0.02 - 6 mm/r
Metric thread range: 0.5 - 120 mm
Inch thread range: 60 - 1/4 Tpi
Module thread range: 0.125 - 30
DP thread range: Array
Cross slide travel: 315 mm
Top slide travel: 90 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 230 mm
Motor power: 11 kW
Weight: 3310 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Distance between centers: 2000 mm
Centre height: 315 mm
Spindle bore: 103 mm
swing over cross slide: 430 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 11
Spindle taper: 120 M
Spindle speed steps: 21
Spindle revs: Array rpm
Number of feeds: 120
Longitudinal feed range: 0.04 - 12 mm/r
Cross feed range: 0.02 - 6 mm/r
Metric thread range: 0.5 - 120 mm
Inch thread range: 60 - 1/4 Tpi
Module thread range: 0.125 - 30
DP thread range: Array
Cross slide travel: 315 mm
Top slide travel: 90 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 230 mm
Motor power: 11 kW
Weight: 3310 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
1
Travail des métaux et machines-outilsMachines à travailler la tôlePlieuses
Shaft diameter: 35Upper roll diameter: 137 mmLower roll diameter: 137 mmDriven rolls: 3Motor power: 1.1 kWSpeed: 7 m/minFlat steel vertical position (section / min. diameter): 35x8 mm / 300 mmFlat steel horizontal position (section / min. diameter): 50x12 mm / 400 mmSquare bar (section / min. diameter): 18x18 mm / 250 mmRound bar (section / min. diameter): Ø 22 mm / 200 mmTube (section / min. diameter): Ø 40x1,5 mm / 500 mmForm tube vertical position (Querschnitt / min. Durchmesser): 30x15x2,5 mm / 500 mmForm tube square (section / min. diameter): 25x25x2 mm / 450 mmAngle leg outside (Querschnitt / min. Durchmesser): 35x35x5 mm / 400 mmAngle leg inside (section / min. diameter): 30x30x4 mm / 550 mmLength: 1050 mmWidth: 500 mmHeight: 1250 mmWeight: 350 kg
Shaft diameter: 35
Upper roll diameter: 137 mm
Lower roll diameter: 137 mm
Driven rolls: 3
Motor power: 1.1 kW
Speed: 7 m/min
Flat steel vertical position (section / min. diameter): 35x8 mm / 300 mm
Flat steel horizontal position (section / min. diameter): 50x12 mm / 400 mm
Square bar (section / min. diameter): 18x18 mm / 250 mm
Round bar (section / min. diameter): Ø 22 mm / 200 mm
Tube (section / min. diameter): Ø 40x1,5 mm / 500 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 30x15x2,5 mm / 500 mm
Form tube square (section / min. diameter): 25x25x2 mm / 450 mm
Angle leg outside (Querschnitt / min. Durchmesser): 35x35x5 mm / 400 mm
Angle leg inside (section / min. diameter): 30x30x4 mm / 550 mm
Length: 1050 mm
Width: 500 mm
Height: 1250 mm
Weight: 350 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Upper roll diameter: 137 mm
Lower roll diameter: 137 mm
Driven rolls: 3
Motor power: 1.1 kW
Speed: 7 m/min
Flat steel vertical position (section / min. diameter): 35x8 mm / 300 mm
Flat steel horizontal position (section / min. diameter): 50x12 mm / 400 mm
Square bar (section / min. diameter): 18x18 mm / 250 mm
Round bar (section / min. diameter): Ø 22 mm / 200 mm
Tube (section / min. diameter): Ø 40x1,5 mm / 500 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 30x15x2,5 mm / 500 mm
Form tube square (section / min. diameter): 25x25x2 mm / 450 mm
Angle leg outside (Querschnitt / min. Durchmesser): 35x35x5 mm / 400 mm
Angle leg inside (section / min. diameter): 30x30x4 mm / 550 mm
Length: 1050 mm
Width: 500 mm
Height: 1250 mm
Weight: 350 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
5
Travail des métaux et machines-outilsMachines à travailler la tôlePlieuses
Shaft diameter: 30Upper roll diameter: 148 mmLower roll diameter: 118 mmDriven rolls: 2Motor power: 0.7 / 0,85 kWSpeed: 2/4 m/minFlat steel vertical position (section / min. diameter): 50x10 mm / 1.800 mm, 20x6 mm / 300 mmFlat steel horizontal position (section / min. diameter): 80x15 mm / 700 mm, 30 x 6 mm / 400 mmSquare bar (section / min. diameter): 30x30 mm / 900 mm, 10x10 mm / 200 mmRound bar (section / min. diameter): Ø 30 mm / 900 mm, Ø 10 mm / 200 mmTube (section / min. diameter): Ø 60x1,5 mm / 1.000 mm, Ø 25x1,5 mm / 600 mm, 1 1/2"x2,9 mm / 600 mm, 1/4"x1,8 mm / 300 mmForm tube vertical position (Querschnitt / min. Durchmesser): 50x30x3 mm / 1.200 mm, 40x20x2 mm / 800 mmForm tube square (section / min. diameter): 40x40x3 mm / 1.200 mm, 30x30x2 mm / 800 mmAngle leg outside (Querschnitt / min. Durchmesser): 40x40x5 mm / 600 mm, 30x30x4 mm / 300 mmAngle leg inside (section / min. diameter): 35x35x5 mm / 600 mm, 30x30x4 mm / 400 mmLength: 600 mmWidth: 800 mmHeight: 1450 mmWeight: 220 kg
Shaft diameter: 30
Upper roll diameter: 148 mm
Lower roll diameter: 118 mm
Driven rolls: 2
Motor power: 0.7 / 0,85 kW
Speed: 2/4 m/min
Flat steel vertical position (section / min. diameter): 50x10 mm / 1.800 mm, 20x6 mm / 300 mm
Flat steel horizontal position (section / min. diameter): 80x15 mm / 700 mm, 30 x 6 mm / 400 mm
Square bar (section / min. diameter): 30x30 mm / 900 mm, 10x10 mm / 200 mm
Round bar (section / min. diameter): Ø 30 mm / 900 mm, Ø 10 mm / 200 mm
Tube (section / min. diameter): Ø 60x1,5 mm / 1.000 mm, Ø 25x1,5 mm / 600 mm, 1 1/2"x2,9 mm / 600 mm, 1/4"x1,8 mm / 300 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 50x30x3 mm / 1.200 mm, 40x20x2 mm / 800 mm
Form tube square (section / min. diameter): 40x40x3 mm / 1.200 mm, 30x30x2 mm / 800 mm
Angle leg outside (Querschnitt / min. Durchmesser): 40x40x5 mm / 600 mm, 30x30x4 mm / 300 mm
Angle leg inside (section / min. diameter): 35x35x5 mm / 600 mm, 30x30x4 mm / 400 mm
Length: 600 mm
Width: 800 mm
Height: 1450 mm
Weight: 220 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Upper roll diameter: 148 mm
Lower roll diameter: 118 mm
Driven rolls: 2
Motor power: 0.7 / 0,85 kW
Speed: 2/4 m/min
Flat steel vertical position (section / min. diameter): 50x10 mm / 1.800 mm, 20x6 mm / 300 mm
Flat steel horizontal position (section / min. diameter): 80x15 mm / 700 mm, 30 x 6 mm / 400 mm
Square bar (section / min. diameter): 30x30 mm / 900 mm, 10x10 mm / 200 mm
Round bar (section / min. diameter): Ø 30 mm / 900 mm, Ø 10 mm / 200 mm
Tube (section / min. diameter): Ø 60x1,5 mm / 1.000 mm, Ø 25x1,5 mm / 600 mm, 1 1/2"x2,9 mm / 600 mm, 1/4"x1,8 mm / 300 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 50x30x3 mm / 1.200 mm, 40x20x2 mm / 800 mm
Form tube square (section / min. diameter): 40x40x3 mm / 1.200 mm, 30x30x2 mm / 800 mm
Angle leg outside (Querschnitt / min. Durchmesser): 40x40x5 mm / 600 mm, 30x30x4 mm / 300 mm
Angle leg inside (section / min. diameter): 35x35x5 mm / 600 mm, 30x30x4 mm / 400 mm
Length: 600 mm
Width: 800 mm
Height: 1450 mm
Weight: 220 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
1
Travail des métaux et machines-outilsMachines à travailler la tôleCisailles à section en acier
X-axis: 3000 mmPositioning speed: 24 m/minRepeat accuracy: 2 mmWeight: 250 kg
X-axis: 3000 mm
Positioning speed: 24 m/min
Repeat accuracy: 2 mm
Weight: 250 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Positioning speed: 24 m/min
Repeat accuracy: 2 mm
Weight: 250 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
2
Travail des métaux et machines-outilsTours
Swing over bed: 760 mmDistance between centers: 3000 mmCentre height: 380 mmSpindle bore: 132 mmswing over cross slide: 520 mmWidth of bed: 560 mmSpindle nose / DIN55027: 11Spindle taper: 140 MRevs continuous variable in gear steps: 3Revs continuous variable: 7 - 42, 28 - 170, 165 - 1.015 rpmNumber of feeds: 150Longitudinal feed range: 0.039 - 18 mm/rCross feed range: 0.02 - 9 mm/rMetric thread range: 0.5 - 180 mmInch thread range: 60 - 1/6 TpiModule thread range: 0.125 - 45DP thread range: ArrayCross slide travel: 410 mmTop slide travel: 150 mmTailstock quill diameter: 105 mmTailstock quill taper: 6 MKTailstock travel: 225 mmMotor power: 15 kWWeight: 4470 kg
Swing over bed: 760 mm
Distance between centers: 3000 mm
Centre height: 380 mm
Spindle bore: 132 mm
swing over cross slide: 520 mm
Width of bed: 560 mm
Spindle nose / DIN55027: 11
Spindle taper: 140 M
Revs continuous variable in gear steps: 3
Revs continuous variable: 7 - 42, 28 - 170, 165 - 1.015 rpm
Number of feeds: 150
Longitudinal feed range: 0.039 - 18 mm/r
Cross feed range: 0.02 - 9 mm/r
Metric thread range: 0.5 - 180 mm
Inch thread range: 60 - 1/6 Tpi
Module thread range: 0.125 - 45
DP thread range: Array
Cross slide travel: 410 mm
Top slide travel: 150 mm
Tailstock quill diameter: 105 mm
Tailstock quill taper: 6 MK
Tailstock travel: 225 mm
Motor power: 15 kW
Weight: 4470 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Distance between centers: 3000 mm
Centre height: 380 mm
Spindle bore: 132 mm
swing over cross slide: 520 mm
Width of bed: 560 mm
Spindle nose / DIN55027: 11
Spindle taper: 140 M
Revs continuous variable in gear steps: 3
Revs continuous variable: 7 - 42, 28 - 170, 165 - 1.015 rpm
Number of feeds: 150
Longitudinal feed range: 0.039 - 18 mm/r
Cross feed range: 0.02 - 9 mm/r
Metric thread range: 0.5 - 180 mm
Inch thread range: 60 - 1/6 Tpi
Module thread range: 0.125 - 45
DP thread range: Array
Cross slide travel: 410 mm
Top slide travel: 150 mm
Tailstock quill diameter: 105 mm
Tailstock quill taper: 6 MK
Tailstock travel: 225 mm
Motor power: 15 kW
Weight: 4470 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
2
Travail des métaux et machines-outilsTours
Swing over bed: 600 mmDistance between centers: 2000 mmCentre height: 300 mmSpindle bore: 80 mmswing over cross slide: 400 mmWidth of bed: 400 mmSpindle nose / DIN55027: 8Spindle taper: 90 MRevs continuous variable in gear steps: 3Revs continuous variable: 8-62, 62-500, 250-2.000 rpmNumber of feeds: 160Number of threads: 64Metric thread range: 0.5 - 120 mmInch thread range: 120 - 1/4 TpiModule thread range: 0.125 - 30Cross slide travel: 315 mmTop slide travel: 130 mmTailstock quill diameter: 90 mmTailstock quill taper: 5 MKTailstock travel: 230 mmMotor power: 11 kWLength: 3600 mmWidth: 1500 mmHeight: 1650 mmWeight: 3110 kg
Swing over bed: 600 mm
Distance between centers: 2000 mm
Centre height: 300 mm
Spindle bore: 80 mm
swing over cross slide: 400 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 8
Spindle taper: 90 M
Revs continuous variable in gear steps: 3
Revs continuous variable: 8-62, 62-500, 250-2.000 rpm
Number of feeds: 160
Number of threads: 64
Metric thread range: 0.5 - 120 mm
Inch thread range: 120 - 1/4 Tpi
Module thread range: 0.125 - 30
Cross slide travel: 315 mm
Top slide travel: 130 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 230 mm
Motor power: 11 kW
Length: 3600 mm
Width: 1500 mm
Height: 1650 mm
Weight: 3110 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Distance between centers: 2000 mm
Centre height: 300 mm
Spindle bore: 80 mm
swing over cross slide: 400 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 8
Spindle taper: 90 M
Revs continuous variable in gear steps: 3
Revs continuous variable: 8-62, 62-500, 250-2.000 rpm
Number of feeds: 160
Number of threads: 64
Metric thread range: 0.5 - 120 mm
Inch thread range: 120 - 1/4 Tpi
Module thread range: 0.125 - 30
Cross slide travel: 315 mm
Top slide travel: 130 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 230 mm
Motor power: 11 kW
Length: 3600 mm
Width: 1500 mm
Height: 1650 mm
Weight: 3110 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
2
Travail des métaux et machines-outilsPonceuses
Distance spindle - table: 445 mmTable: 460 x 200 mmGrinding lenght: 460 mmMagnetic table: 450 x 200 mmTable speed: 0,1 - 25 m/minCross feed rapid travel: 0 - 3000 m/minMax. cross feed: 220 mmAutomatic vertical feed: 340 mmRapid vertical feed approx.: 0 - 3000 mm/minFine vertical feed: 0.001 mmSpindle revs: 1000 - 7000 rpmSpindle motor: 3 kWHydraulic motor: 0.7 kWCross feed motor: 1.1 kWFeed motor grinding wheel: 1.1 kWTable height: 1015 mmMax. workpiece weight on magnetic table: 175 kgMax. workpiece weight on t-slot table: 210 kgGrinding wheel dimensions: Dm. 205 x 12,7 x 31,75 mmLength: 2510 mmWidth: 2515 mmHeight: 2010 mmWeight: 1550 kg
Distance spindle - table: 445 mm
Table: 460 x 200 mm
Grinding lenght: 460 mm
Magnetic table: 450 x 200 mm
Table speed: 0,1 - 25 m/min
Cross feed rapid travel: 0 - 3000 m/min
Max. cross feed: 220 mm
Automatic vertical feed: 340 mm
Rapid vertical feed approx.: 0 - 3000 mm/min
Fine vertical feed: 0.001 mm
Spindle revs: 1000 - 7000 rpm
Spindle motor: 3 kW
Hydraulic motor: 0.7 kW
Cross feed motor: 1.1 kW
Feed motor grinding wheel: 1.1 kW
Table height: 1015 mm
Max. workpiece weight on magnetic table: 175 kg
Max. workpiece weight on t-slot table: 210 kg
Grinding wheel dimensions: Dm. 205 x 12,7 x 31,75 mm
Length: 2510 mm
Width: 2515 mm
Height: 2010 mm
Weight: 1550 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Table: 460 x 200 mm
Grinding lenght: 460 mm
Magnetic table: 450 x 200 mm
Table speed: 0,1 - 25 m/min
Cross feed rapid travel: 0 - 3000 m/min
Max. cross feed: 220 mm
Automatic vertical feed: 340 mm
Rapid vertical feed approx.: 0 - 3000 mm/min
Fine vertical feed: 0.001 mm
Spindle revs: 1000 - 7000 rpm
Spindle motor: 3 kW
Hydraulic motor: 0.7 kW
Cross feed motor: 1.1 kW
Feed motor grinding wheel: 1.1 kW
Table height: 1015 mm
Max. workpiece weight on magnetic table: 175 kg
Max. workpiece weight on t-slot table: 210 kg
Grinding wheel dimensions: Dm. 205 x 12,7 x 31,75 mm
Length: 2510 mm
Width: 2515 mm
Height: 2010 mm
Weight: 1550 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
5
Travail des métaux et machines-outilsMachines à travailler la tôleMachines de laminage circulaire
Bending length: 2050 mmMax. bending capacity - mild steel: 10Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 10 mmMax. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 8 mmMax. plate thickness with prebending at D=5x upper roll diam. - mild steel: 8 mmMax. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 6 mmUpper roll diameter: 200 - 220 mmLower roll diameter: 200 - 220 mmLateral roll diameter: 160 mmBending speed: 1,5 / 6 m/minMotor power: 5.5 kWLength: 4400 mmWidth: 1150 mmHeight: 1250 mmWeight: 3950 kg
Bending length: 2050 mm
Max. bending capacity - mild steel: 10
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 10 mm
Max. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 8 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 8 mm
Max. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 6 mm
Upper roll diameter: 200 - 220 mm
Lower roll diameter: 200 - 220 mm
Lateral roll diameter: 160 mm
Bending speed: 1,5 / 6 m/min
Motor power: 5.5 kW
Length: 4400 mm
Width: 1150 mm
Height: 1250 mm
Weight: 3950 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Max. bending capacity - mild steel: 10
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 10 mm
Max. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 8 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 8 mm
Max. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 6 mm
Upper roll diameter: 200 - 220 mm
Lower roll diameter: 200 - 220 mm
Lateral roll diameter: 160 mm
Bending speed: 1,5 / 6 m/min
Motor power: 5.5 kW
Length: 4400 mm
Width: 1150 mm
Height: 1250 mm
Weight: 3950 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
5
Travail des métaux et machines-outilsMachines à travailler la tôleMachines de laminage circulaire
Bending length: 2050 mmMax. bending capacity - mild steel: 8Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 8 mmMax. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 6 mmMax. plate thickness with prebending at D=5x upper roll diam. - mild steel: 6 mmMax. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 4 mmUpper roll diameter: 180 mmLower roll diameter: 180 mmLateral roll diameter: 150 mmBending speed: 1,5 / 6 m/minMotor power: 5.5 kWLength: 4400 mmWidth: 1150 mmHeight: 1250 mmWeight: 3790 kg
Bending length: 2050 mm
Max. bending capacity - mild steel: 8
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 8 mm
Max. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 6 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 6 mm
Max. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 4 mm
Upper roll diameter: 180 mm
Lower roll diameter: 180 mm
Lateral roll diameter: 150 mm
Bending speed: 1,5 / 6 m/min
Motor power: 5.5 kW
Length: 4400 mm
Width: 1150 mm
Height: 1250 mm
Weight: 3790 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Max. bending capacity - mild steel: 8
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 8 mm
Max. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 6 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 6 mm
Max. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 4 mm
Upper roll diameter: 180 mm
Lower roll diameter: 180 mm
Lateral roll diameter: 150 mm
Bending speed: 1,5 / 6 m/min
Motor power: 5.5 kW
Length: 4400 mm
Width: 1150 mm
Height: 1250 mm
Weight: 3790 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
9
Travail des métaux et machines-outilsSciageScies à courroies
Saw frame: Double columnBand dimensions: 8200x41x1,3 mmBand speed continous: 20-100 m/minCutting capacity 0° round: 810 mmCutting capacity 0° square: 750 mmCutting capacity 0° rectangular: 910x750 mmCutting capacity 45°: rund 600 mm, quadrat 600 mm, rechteck 750 x 600 mmCutting capacity 60°: rund 360 mm, quadrat 360 mm, rechteck 750 x 360 mmWorking height: 725 mmCoolant pump motor: 0.12 kWMotor: 4 kWLength: 4020 mmWidth: 1600 mmHeight: 2450 mmWeight: 3970 kg
Saw frame: Double column
Band dimensions: 8200x41x1,3 mm
Band speed continous: 20-100 m/min
Cutting capacity 0° round: 810 mm
Cutting capacity 0° square: 750 mm
Cutting capacity 0° rectangular: 910x750 mm
Cutting capacity 45°: rund 600 mm, quadrat 600 mm, rechteck 750 x 600 mm
Cutting capacity 60°: rund 360 mm, quadrat 360 mm, rechteck 750 x 360 mm
Working height: 725 mm
Coolant pump motor: 0.12 kW
Motor: 4 kW
Length: 4020 mm
Width: 1600 mm
Height: 2450 mm
Weight: 3970 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Band dimensions: 8200x41x1,3 mm
Band speed continous: 20-100 m/min
Cutting capacity 0° round: 810 mm
Cutting capacity 0° square: 750 mm
Cutting capacity 0° rectangular: 910x750 mm
Cutting capacity 45°: rund 600 mm, quadrat 600 mm, rechteck 750 x 600 mm
Cutting capacity 60°: rund 360 mm, quadrat 360 mm, rechteck 750 x 360 mm
Working height: 725 mm
Coolant pump motor: 0.12 kW
Motor: 4 kW
Length: 4020 mm
Width: 1600 mm
Height: 2450 mm
Weight: 3970 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
6
Travail des métaux et machines-outilsMachines à travailler la tôlePlieuses pivotantes
Bending length: 4010 mmBending capacity steel 400 N/mm²: 1.5 mmBending capacity Alu 190 N/mm²: 2 mmNo. of stand and tension arm units: 4
Bending length: 4010 mm
Bending capacity steel 400 N/mm²: 1.5 mm
Bending capacity Alu 190 N/mm²: 2 mm
No. of stand and tension arm units: 4
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Bending capacity steel 400 N/mm²: 1.5 mm
Bending capacity Alu 190 N/mm²: 2 mm
No. of stand and tension arm units: 4
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
11
Travail des métaux et machines-outilsPonceuses
Distance spindle - table: 850 mmTable: 1000 x 600 mmGrinding lenght: 1000 mmMagnetic table: 1000 x 600 mmTable movement hydraulic: 1000 mmTable speed: 5 - 25 m/minCross feed rapid travel: 1250 m/minCross fine feed: 0.02 mmRapid vertical feed approx.: 400 mm/minFine vertical feed: 0.001 mmSpindle revs: 1450 rpmSpindle motor: 11 kWHydraulic motor: 3.7 kWCross feed motor: 0.37 kWTotal power: 20 kWMaximal table load: 1500 kgMax. workpiece weight on magnetic table: 1120 kgMax. workpiece weight on t-slot table: 1500 kgGrinding wheel dimensions: 355 x 75 x 127 mmTransverse feed speed: 3 - 32 mm/minLength: 3700 mmWidth: 4000 mmHeight: 3250 mmWeight: 7400 kg
Distance spindle - table: 850 mm
Table: 1000 x 600 mm
Grinding lenght: 1000 mm
Magnetic table: 1000 x 600 mm
Table movement hydraulic: 1000 mm
Table speed: 5 - 25 m/min
Cross feed rapid travel: 1250 m/min
Cross fine feed: 0.02 mm
Rapid vertical feed approx.: 400 mm/min
Fine vertical feed: 0.001 mm
Spindle revs: 1450 rpm
Spindle motor: 11 kW
Hydraulic motor: 3.7 kW
Cross feed motor: 0.37 kW
Total power: 20 kW
Maximal table load: 1500 kg
Max. workpiece weight on magnetic table: 1120 kg
Max. workpiece weight on t-slot table: 1500 kg
Grinding wheel dimensions: 355 x 75 x 127 mm
Transverse feed speed: 3 - 32 mm/min
Length: 3700 mm
Width: 4000 mm
Height: 3250 mm
Weight: 7400 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Table: 1000 x 600 mm
Grinding lenght: 1000 mm
Magnetic table: 1000 x 600 mm
Table movement hydraulic: 1000 mm
Table speed: 5 - 25 m/min
Cross feed rapid travel: 1250 m/min
Cross fine feed: 0.02 mm
Rapid vertical feed approx.: 400 mm/min
Fine vertical feed: 0.001 mm
Spindle revs: 1450 rpm
Spindle motor: 11 kW
Hydraulic motor: 3.7 kW
Cross feed motor: 0.37 kW
Total power: 20 kW
Maximal table load: 1500 kg
Max. workpiece weight on magnetic table: 1120 kg
Max. workpiece weight on t-slot table: 1500 kg
Grinding wheel dimensions: 355 x 75 x 127 mm
Transverse feed speed: 3 - 32 mm/min
Length: 3700 mm
Width: 4000 mm
Height: 3250 mm
Weight: 7400 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
14
Travail des métaux et machines-outilsPonceuses
Distance spindle - table: 600 mmTable: 400 x 1000 mmGrinding area: 1.015 x 405 x 610 mmGrinding lenght: 1015 mmMagnetic table: 1000 x 400 mmMax. work piece weight: 670 kgTable movement hydraulic: 1100 mmTable speed: 5 - 25 m/minCross feed rapid travel: 0 - 2,250 m/minAutomatic cross feed incremental: 3 - 32 mmMax. cross feed: 450 mmCross fine feed: 0.001 - 32 mmAutomatic vertical feed: 440 mmRapid vertical feed approx.: 0 - 675 mm/minFine vertical feed: 0.001 - 0.04 mmSpindle revs: 500 - 2.000 rpmSpindle motor: 5 kWHydraulic motor: 1.5 kWCross feed motor: 1.1 kWFeed motor grinding wheel: 1.1 kWMax. workpiece weight on magnetic table: 423 kgMax. workpiece weight on t-slot table: 670 kgGrinding wheel dimensions: 355 x 50 x 127 mmaut. feed: 0,001 - 0,04 mmRapid feed approx: 675 mm/minLength: 3630 mmWidth: 2682 mmHeight: 2200 mmWeight: 4800 kg
Distance spindle - table: 600 mm
Table: 400 x 1000 mm
Grinding area: 1.015 x 405 x 610 mm
Grinding lenght: 1015 mm
Magnetic table: 1000 x 400 mm
Max. work piece weight: 670 kg
Table movement hydraulic: 1100 mm
Table speed: 5 - 25 m/min
Cross feed rapid travel: 0 - 2,250 m/min
Automatic cross feed incremental: 3 - 32 mm
Max. cross feed: 450 mm
Cross fine feed: 0.001 - 32 mm
Automatic vertical feed: 440 mm
Rapid vertical feed approx.: 0 - 675 mm/min
Fine vertical feed: 0.001 - 0.04 mm
Spindle revs: 500 - 2.000 rpm
Spindle motor: 5 kW
Hydraulic motor: 1.5 kW
Cross feed motor: 1.1 kW
Feed motor grinding wheel: 1.1 kW
Max. workpiece weight on magnetic table: 423 kg
Max. workpiece weight on t-slot table: 670 kg
Grinding wheel dimensions: 355 x 50 x 127 mm
aut. feed: 0,001 - 0,04 mm
Rapid feed approx: 675 mm/min
Length: 3630 mm
Width: 2682 mm
Height: 2200 mm
Weight: 4800 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Table: 400 x 1000 mm
Grinding area: 1.015 x 405 x 610 mm
Grinding lenght: 1015 mm
Magnetic table: 1000 x 400 mm
Max. work piece weight: 670 kg
Table movement hydraulic: 1100 mm
Table speed: 5 - 25 m/min
Cross feed rapid travel: 0 - 2,250 m/min
Automatic cross feed incremental: 3 - 32 mm
Max. cross feed: 450 mm
Cross fine feed: 0.001 - 32 mm
Automatic vertical feed: 440 mm
Rapid vertical feed approx.: 0 - 675 mm/min
Fine vertical feed: 0.001 - 0.04 mm
Spindle revs: 500 - 2.000 rpm
Spindle motor: 5 kW
Hydraulic motor: 1.5 kW
Cross feed motor: 1.1 kW
Feed motor grinding wheel: 1.1 kW
Max. workpiece weight on magnetic table: 423 kg
Max. workpiece weight on t-slot table: 670 kg
Grinding wheel dimensions: 355 x 50 x 127 mm
aut. feed: 0,001 - 0,04 mm
Rapid feed approx: 675 mm/min
Length: 3630 mm
Width: 2682 mm
Height: 2200 mm
Weight: 4800 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
7
Travail des métaux et machines-outilsPressesPresses d'essai
pressing capacity: 150 toCylinder fix or moveable: fixStroke: 300 mmDaylight: 610 mmDistance between columns: 1020 mmRapid speed: 9 mm/sWorking speed: 5 mm/sRetraction speed: 10 mm/sTable: 600x1020 mmHole in table: 100 mmHole distance: 190 mmLength: 2110 mmWidth: 1000 mmHeight: 2470 mmWeight: 2450 kg
pressing capacity: 150 to
Cylinder fix or moveable: fix
Stroke: 300 mm
Daylight: 610 mm
Distance between columns: 1020 mm
Rapid speed: 9 mm/s
Working speed: 5 mm/s
Retraction speed: 10 mm/s
Table: 600x1020 mm
Hole in table: 100 mm
Hole distance: 190 mm
Length: 2110 mm
Width: 1000 mm
Height: 2470 mm
Weight: 2450 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Cylinder fix or moveable: fix
Stroke: 300 mm
Daylight: 610 mm
Distance between columns: 1020 mm
Rapid speed: 9 mm/s
Working speed: 5 mm/s
Retraction speed: 10 mm/s
Table: 600x1020 mm
Hole in table: 100 mm
Hole distance: 190 mm
Length: 2110 mm
Width: 1000 mm
Height: 2470 mm
Weight: 2450 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
5
Travail des métaux et machines-outilsMachines à travailler la tôleMachines de laminage circulaire
Bending length: 1550 mmMax. bending capacity - mild steel: 4.5Max. plate thickness without prebending - mild steel: 4.5 mmMax. plate thickness with prebending - mild steel: 3.5 mmMax. plate thickness without prebending at D=5x upper roll diam. - mild steel: 4.5 mmMax. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 3.5 mmMax. plate thickness with prebending at D=5x upper roll diam. - mild steel: 3.5 mmMax. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 2.5 mmUpper roll diameter: 130 mmLower roll diameter: 130 mmLateral roll diameter: 130 mmBending speed: 5 m/minMotor power: 2,2 + 1,1 kWLength: 3300 mmWidth: 1150 mmHeight: 1110 mmWeight: 2370 kg
Bending length: 1550 mm
Max. bending capacity - mild steel: 4.5
Max. plate thickness without prebending - mild steel: 4.5 mm
Max. plate thickness with prebending - mild steel: 3.5 mm
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 4.5 mm
Max. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 3.5 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 3.5 mm
Max. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 2.5 mm
Upper roll diameter: 130 mm
Lower roll diameter: 130 mm
Lateral roll diameter: 130 mm
Bending speed: 5 m/min
Motor power: 2,2 + 1,1 kW
Length: 3300 mm
Width: 1150 mm
Height: 1110 mm
Weight: 2370 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Max. bending capacity - mild steel: 4.5
Max. plate thickness without prebending - mild steel: 4.5 mm
Max. plate thickness with prebending - mild steel: 3.5 mm
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 4.5 mm
Max. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 3.5 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 3.5 mm
Max. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 2.5 mm
Upper roll diameter: 130 mm
Lower roll diameter: 130 mm
Lateral roll diameter: 130 mm
Bending speed: 5 m/min
Motor power: 2,2 + 1,1 kW
Length: 3300 mm
Width: 1150 mm
Height: 1110 mm
Weight: 2370 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
2
Travail des métaux et machines-outilsPressesPresses excentriques
pressing capacity: 15 toTonnage rating point: 1.4 mmTable length: 320 mmTable width: 490 mmHole in table: 130 mmStroke: 1 - 40 mmStrokes: 200 1/minRam guides: 4Ram adjustment: 40 mmRam hole: 30 mmThroat depth: 200 mmDaylight: 215 mmMotor: 1.5 kWLength: 1160 mmWidth: 1180 mmHeight: 1730 mmWeight: 922 kg
pressing capacity: 15 to
Tonnage rating point: 1.4 mm
Table length: 320 mm
Table width: 490 mm
Hole in table: 130 mm
Stroke: 1 - 40 mm
Strokes: 200 1/min
Ram guides: 4
Ram adjustment: 40 mm
Ram hole: 30 mm
Throat depth: 200 mm
Daylight: 215 mm
Motor: 1.5 kW
Length: 1160 mm
Width: 1180 mm
Height: 1730 mm
Weight: 922 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Tonnage rating point: 1.4 mm
Table length: 320 mm
Table width: 490 mm
Hole in table: 130 mm
Stroke: 1 - 40 mm
Strokes: 200 1/min
Ram guides: 4
Ram adjustment: 40 mm
Ram hole: 30 mm
Throat depth: 200 mm
Daylight: 215 mm
Motor: 1.5 kW
Length: 1160 mm
Width: 1180 mm
Height: 1730 mm
Weight: 922 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
2
Travail des métaux et machines-outilsMachines à travailler la tôlePerforation
Punching power: 110 tonMax. diameter at sheet thickness (mild steel): 4-30 mm
Punching power: 110 ton
Max. diameter at sheet thickness (mild steel): 4-30 mm
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Max. diameter at sheet thickness (mild steel): 4-30 mm
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
1
Travail des métaux et machines-outilsMachines à travailler la tôlePerforation
Punching power: 50 tonThroat depth: 130 mmMax. diameter at sheet thickness (mild steel): 13/27 mmMax. number of strokes at 20 mm stroke: 23 1/minMotor: 3 kWLength: 1100 mmWidth: 900 mmHeight: 1550 mmWeight: 355 kg
Punching power: 50 ton
Throat depth: 130 mm
Max. diameter at sheet thickness (mild steel): 13/27 mm
Max. number of strokes at 20 mm stroke: 23 1/min
Motor: 3 kW
Length: 1100 mm
Width: 900 mm
Height: 1550 mm
Weight: 355 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Throat depth: 130 mm
Max. diameter at sheet thickness (mild steel): 13/27 mm
Max. number of strokes at 20 mm stroke: 23 1/min
Motor: 3 kW
Length: 1100 mm
Width: 900 mm
Height: 1550 mm
Weight: 355 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
4
Travail des métaux et machines-outilsSciageScies à courroies
Saw frame: Pivot frameBand dimensions: 3120x27x0,9 mmBand speed continous: 20-100 m/minCutting capacity 0° round: 280 mmCutting capacity 0° square: 240 mmCutting capacity 0° rectangular: 310x240 mmCutting capacity 45°: rund 230 mm, quadrat 230 mm, rechteck 230 x 230 mmCutting capacity 60°: rund 140 mm, quadrat 140 mm, rechteck 140 x 140 mmCutting capacity - 45°: rund 200 mm, quadrat 170 mm, rechteck 220 x 100 mmMin. rest piece length: 240 mmWorking height: 835 mmCoolant pump motor: 0.12 kWHydraulic motor: 0.37 kWMotor: 1.5 kWTorque feeding carriage motor: 1.95 NmTorque motor for automatic bow rotation: 1.95 NmLength: 2800 mmWidth: 2000 mmHeight: 1820 mmWeight: 1200 kg
Saw frame: Pivot frame
Band dimensions: 3120x27x0,9 mm
Band speed continous: 20-100 m/min
Cutting capacity 0° round: 280 mm
Cutting capacity 0° square: 240 mm
Cutting capacity 0° rectangular: 310x240 mm
Cutting capacity 45°: rund 230 mm, quadrat 230 mm, rechteck 230 x 230 mm
Cutting capacity 60°: rund 140 mm, quadrat 140 mm, rechteck 140 x 140 mm
Cutting capacity - 45°: rund 200 mm, quadrat 170 mm, rechteck 220 x 100 mm
Min. rest piece length: 240 mm
Working height: 835 mm
Coolant pump motor: 0.12 kW
Hydraulic motor: 0.37 kW
Motor: 1.5 kW
Torque feeding carriage motor: 1.95 Nm
Torque motor for automatic bow rotation: 1.95 Nm
Length: 2800 mm
Width: 2000 mm
Height: 1820 mm
Weight: 1200 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Band dimensions: 3120x27x0,9 mm
Band speed continous: 20-100 m/min
Cutting capacity 0° round: 280 mm
Cutting capacity 0° square: 240 mm
Cutting capacity 0° rectangular: 310x240 mm
Cutting capacity 45°: rund 230 mm, quadrat 230 mm, rechteck 230 x 230 mm
Cutting capacity 60°: rund 140 mm, quadrat 140 mm, rechteck 140 x 140 mm
Cutting capacity - 45°: rund 200 mm, quadrat 170 mm, rechteck 220 x 100 mm
Min. rest piece length: 240 mm
Working height: 835 mm
Coolant pump motor: 0.12 kW
Hydraulic motor: 0.37 kW
Motor: 1.5 kW
Torque feeding carriage motor: 1.95 Nm
Torque motor for automatic bow rotation: 1.95 Nm
Length: 2800 mm
Width: 2000 mm
Height: 1820 mm
Weight: 1200 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
2
Travail des métaux et machines-outilsMachines à travailler la tôleMachines à cintrer les tuyauteries
Flexion modulus: 6 cm³Round tube: Ø 60 x 2 mmStandard steel tube: 50 x 3,31 mmGas tube: Ø 1”1/4 x 80 mmStainless steel: Ø 50 x 2 mmHard copper and aluminium: Ø 64 x 2 mmSquare tube: Ø 40 x 40 x 3 mmRect. tube easy way: 25 x 50 x 6 mmRect. tube hard way: 50 x 25 x 2,7 mmRect. tube: Ø 50 x 25 x 3 mm bzw. Ø 25 x 50 x 6 mmMax. outer diameter: 64 mmMax. bending radius: 200 mmMin. bending radius: 20 mmMax. bending angle: 210 °Speed: 1,25 / 2,5Motor: 3 kWHydraulic oil capacity: 50 lLength: 4000 mmWidth: 950 mmHeight: 1250 mmWeight: 430 kg
Flexion modulus: 6 cm³
Round tube: Ø 60 x 2 mm
Standard steel tube: 50 x 3,31 mm
Gas tube: Ø 1”1/4 x 80 mm
Stainless steel: Ø 50 x 2 mm
Hard copper and aluminium: Ø 64 x 2 mm
Square tube: Ø 40 x 40 x 3 mm
Rect. tube easy way: 25 x 50 x 6 mm
Rect. tube hard way: 50 x 25 x 2,7 mm
Rect. tube: Ø 50 x 25 x 3 mm bzw. Ø 25 x 50 x 6 mm
Max. outer diameter: 64 mm
Max. bending radius: 200 mm
Min. bending radius: 20 mm
Max. bending angle: 210 °
Speed: 1,25 / 2,5
Motor: 3 kW
Hydraulic oil capacity: 50 l
Length: 4000 mm
Width: 950 mm
Height: 1250 mm
Weight: 430 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Round tube: Ø 60 x 2 mm
Standard steel tube: 50 x 3,31 mm
Gas tube: Ø 1”1/4 x 80 mm
Stainless steel: Ø 50 x 2 mm
Hard copper and aluminium: Ø 64 x 2 mm
Square tube: Ø 40 x 40 x 3 mm
Rect. tube easy way: 25 x 50 x 6 mm
Rect. tube hard way: 50 x 25 x 2,7 mm
Rect. tube: Ø 50 x 25 x 3 mm bzw. Ø 25 x 50 x 6 mm
Max. outer diameter: 64 mm
Max. bending radius: 200 mm
Min. bending radius: 20 mm
Max. bending angle: 210 °
Speed: 1,25 / 2,5
Motor: 3 kW
Hydraulic oil capacity: 50 l
Length: 4000 mm
Width: 950 mm
Height: 1250 mm
Weight: 430 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
6
Travail des métaux et machines-outilsMachines à travailler la tôleMachines à cintrer les tuyauteries
Flexion modulus: 19 cm³Standard steel tube: 38 x 1,5 mmFurniture tube: 38 x 1,5 mmFE35 (for hydraulic tubes): 35 x 3 mmStainless steel AISI304-318: 30 x 2 mmStainless steel AISI308 (food industry): 35 x 1,5 mmBrass soft: 42 x 1,5 mmHard copper and aluminium: 42 x 1,5 mmSoft copper: 50 x 2 mmConduit tube (TAZ): 50 x 2 mmMepla, Gebereit and similar: 50 x 4 mmRoundbar solid (S275JO): 20 mmSquarebar solid (S275JO): 10 x 25 mmFlatsteel solid (S275JO): 25 x 20 (stehend), 25 x 16 (stehend) mmMax. bending radius: 180 mmMin. bending radius: 36 mmMin. tube Ø: 10 mmMax. bending speed: 2 r/minMotor: 0.9 kWLength: 245 mmWidth: 300 mmHeight: 320 mmWeight: 23 kg
Flexion modulus: 19 cm³
Standard steel tube: 38 x 1,5 mm
Furniture tube: 38 x 1,5 mm
FE35 (for hydraulic tubes): 35 x 3 mm
Stainless steel AISI304-318: 30 x 2 mm
Stainless steel AISI308 (food industry): 35 x 1,5 mm
Brass soft: 42 x 1,5 mm
Hard copper and aluminium: 42 x 1,5 mm
Soft copper: 50 x 2 mm
Conduit tube (TAZ): 50 x 2 mm
Mepla, Gebereit and similar: 50 x 4 mm
Roundbar solid (S275JO): 20 mm
Squarebar solid (S275JO): 10 x 25 mm
Flatsteel solid (S275JO): 25 x 20 (stehend), 25 x 16 (stehend) mm
Max. bending radius: 180 mm
Min. bending radius: 36 mm
Min. tube Ø: 10 mm
Max. bending speed: 2 r/min
Motor: 0.9 kW
Length: 245 mm
Width: 300 mm
Height: 320 mm
Weight: 23 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Standard steel tube: 38 x 1,5 mm
Furniture tube: 38 x 1,5 mm
FE35 (for hydraulic tubes): 35 x 3 mm
Stainless steel AISI304-318: 30 x 2 mm
Stainless steel AISI308 (food industry): 35 x 1,5 mm
Brass soft: 42 x 1,5 mm
Hard copper and aluminium: 42 x 1,5 mm
Soft copper: 50 x 2 mm
Conduit tube (TAZ): 50 x 2 mm
Mepla, Gebereit and similar: 50 x 4 mm
Roundbar solid (S275JO): 20 mm
Squarebar solid (S275JO): 10 x 25 mm
Flatsteel solid (S275JO): 25 x 20 (stehend), 25 x 16 (stehend) mm
Max. bending radius: 180 mm
Min. bending radius: 36 mm
Min. tube Ø: 10 mm
Max. bending speed: 2 r/min
Motor: 0.9 kW
Length: 245 mm
Width: 300 mm
Height: 320 mm
Weight: 23 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
3
Travail des métaux et machines-outilsMachines à travailler la tôlePlieuses pivotantes
Bending length: 3100 mmSheet thickness (420 N/mm²): 3.5 mmAntrieb: HydraulicMax. bending angle: 135 °Length: 4300 mmWidth: 1770 mmHeight: 1890 mmWeight: 4520 kg
Bending length: 3100 mm
Sheet thickness (420 N/mm²): 3.5 mm
Antrieb: Hydraulic
Max. bending angle: 135 °
Length: 4300 mm
Width: 1770 mm
Height: 1890 mm
Weight: 4520 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Sheet thickness (420 N/mm²): 3.5 mm
Antrieb: Hydraulic
Max. bending angle: 135 °
Length: 4300 mm
Width: 1770 mm
Height: 1890 mm
Weight: 4520 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
3
Travail des métaux et machines-outilsMachines à travailler la tôlePlieuses pivotantes
Bending length: 3100 mmSheet thickness (420 N/mm²): 2.5 mmAntrieb: HydraulicMax. bending angle: 135 °Length: 4300 mmWidth: 1770 mmHeight: 1890 mmWeight: 4000 kg
Bending length: 3100 mm
Sheet thickness (420 N/mm²): 2.5 mm
Antrieb: Hydraulic
Max. bending angle: 135 °
Length: 4300 mm
Width: 1770 mm
Height: 1890 mm
Weight: 4000 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Sheet thickness (420 N/mm²): 2.5 mm
Antrieb: Hydraulic
Max. bending angle: 135 °
Length: 4300 mm
Width: 1770 mm
Height: 1890 mm
Weight: 4000 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
3
Travail des métaux et machines-outilsMachines à travailler la tôlePlieuses pivotantes
Bending length: 2540 mmSheet thickness (420 N/mm²): 6.5 mmAntrieb: HydraulicMax. bending angle: 135 °Length: 3900 mmWidth: 1750 mmHeight: 2050 mmWeight: 6200 kg
Bending length: 2540 mm
Sheet thickness (420 N/mm²): 6.5 mm
Antrieb: Hydraulic
Max. bending angle: 135 °
Length: 3900 mm
Width: 1750 mm
Height: 2050 mm
Weight: 6200 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Sheet thickness (420 N/mm²): 6.5 mm
Antrieb: Hydraulic
Max. bending angle: 135 °
Length: 3900 mm
Width: 1750 mm
Height: 2050 mm
Weight: 6200 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
3
Travail des métaux et machines-outilsMachines à travailler la tôlePlieuses pivotantes
Bending length: 2540 mmSheet thickness (420 N/mm²): 4.5 mmAntrieb: HydraulicMax. bending angle: 135 °Length: 3900 mmWidth: 1700 mmHeight: 1900 mmWeight: 5100 kg
Bending length: 2540 mm
Sheet thickness (420 N/mm²): 4.5 mm
Antrieb: Hydraulic
Max. bending angle: 135 °
Length: 3900 mm
Width: 1700 mm
Height: 1900 mm
Weight: 5100 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Sheet thickness (420 N/mm²): 4.5 mm
Antrieb: Hydraulic
Max. bending angle: 135 °
Length: 3900 mm
Width: 1700 mm
Height: 1900 mm
Weight: 5100 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
3
Travail des métaux et machines-outilsMachines à travailler la tôlePlieuses pivotantes
Bending length: 2540 mmSheet thickness (420 N/mm²): 3.5 mmAntrieb: HydraulicMax. bending angle: 135 °Motor: 3.7 kWLength: 3850 mmWidth: 1700 mmHeight: 1860 mmWeight: 3900 kg
Bending length: 2540 mm
Sheet thickness (420 N/mm²): 3.5 mm
Antrieb: Hydraulic
Max. bending angle: 135 °
Motor: 3.7 kW
Length: 3850 mm
Width: 1700 mm
Height: 1860 mm
Weight: 3900 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.
Sheet thickness (420 N/mm²): 3.5 mm
Antrieb: Hydraulic
Max. bending angle: 135 °
Motor: 3.7 kW
Length: 3850 mm
Width: 1700 mm
Height: 1860 mm
Weight: 3900 kg
L`annonce a été traduite automatiquement et certaines erreurs de traduction peuvent s`être produites.