10
Машины для обработки пластикаТермопластавтоматы
Ref. no.: 18627Manufacturer: BATTENFELDYear of construction: 2007Clamping unitClamping force: 100 tonOpening stroke: 500 mmDistance between tie bars: 470 x 420 mmMould height min.: 250 mmInjection unitScrew diameter: 22 + 14 mmInjection volume: 47 +13 cm³Shot weight: 45 + 12 gInjection pressure: 2860 + 3000 barMeasurements and weightDimensions: 4,1 x 1,5 x 2,4 mMachine weight: 5000 kgFurther information:2K Co-Injection Moulding MachineThis machine from the prestigious Austrian manufacturer Battenfeld is a 2007 horizontal injection moulding machine with 100 tonnes clamping force and a special Co-Injection (Sandwich Injection) configuration.How Does Co-Injection Work?The two injection units do not operate independently — they meet inside a combined nozzle. First, Unit A injects: the first material adheres to the mould wall and forms the outer skin. Then Unit B follows: the second material flows into the core of the first, pushing it forward. The result is a part with an outer skin of Material 1 and a core of Material 2. If both materials are injected simultaneously or overlapping, a decorative marble or blended colour effect is achieved. The entire process takes place in a single cycle with a standard mould — no expensive rotary platen tooling is required.In the current production of this machine, Unit A feeds green and Unit B feeds yellow material of the same plastic type, both injected simultaneously through a single combined nozzle into the mould. As the green and yellow materials flow side by side and into each other, a natural marbled colour effect is created on the part surface. Permanent and visually appealing coloured surfaces are produced in a single cycle — no labels or post-painting required.
Ref. no.: 18627
Manufacturer: BATTENFELD
Year of construction: 2007
Clamping unit
Clamping force: 100 ton
Opening stroke: 500 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 250 mm
Injection unit
Screw diameter: 22 + 14 mm
Injection volume: 47 +13 cm³
Shot weight: 45 + 12 g
Injection pressure: 2860 + 3000 bar
Measurements and weight
Dimensions: 4,1 x 1,5 x 2,4 m
Machine weight: 5000 kg
Further information:
2K Co-Injection Moulding Machine
This machine from the prestigious Austrian manufacturer Battenfeld is a 2007 horizontal injection moulding machine with 100 tonnes clamping force and a special Co-Injection (Sandwich Injection) configuration.
How Does Co-Injection Work?
The two injection units do not operate independently — they meet inside a combined nozzle. First, Unit A injects: the first material adheres to the mould wall and forms the outer skin. Then Unit B follows: the second material flows into the core of the first, pushing it forward. The result is a part with an outer skin of Material 1 and a core of Material 2. If both materials are injected simultaneously or overlapping, a decorative marble or blended colour effect is achieved. The entire process takes place in a single cycle with a standard mould — no expensive rotary platen tooling is required.
In the current production of this machine, Unit A feeds green and Unit B feeds yellow material of the same plastic type, both injected simultaneously through a single combined nozzle into the mould. As the green and yellow materials flow side by side and into each other, a natural marbled colour effect is created on the part surface. Permanent and visually appealing coloured surfaces are produced in a single cycle — no labels or post-painting required.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: BATTENFELD
Year of construction: 2007
Clamping unit
Clamping force: 100 ton
Opening stroke: 500 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 250 mm
Injection unit
Screw diameter: 22 + 14 mm
Injection volume: 47 +13 cm³
Shot weight: 45 + 12 g
Injection pressure: 2860 + 3000 bar
Measurements and weight
Dimensions: 4,1 x 1,5 x 2,4 m
Machine weight: 5000 kg
Further information:
2K Co-Injection Moulding Machine
This machine from the prestigious Austrian manufacturer Battenfeld is a 2007 horizontal injection moulding machine with 100 tonnes clamping force and a special Co-Injection (Sandwich Injection) configuration.
How Does Co-Injection Work?
The two injection units do not operate independently — they meet inside a combined nozzle. First, Unit A injects: the first material adheres to the mould wall and forms the outer skin. Then Unit B follows: the second material flows into the core of the first, pushing it forward. The result is a part with an outer skin of Material 1 and a core of Material 2. If both materials are injected simultaneously or overlapping, a decorative marble or blended colour effect is achieved. The entire process takes place in a single cycle with a standard mould — no expensive rotary platen tooling is required.
In the current production of this machine, Unit A feeds green and Unit B feeds yellow material of the same plastic type, both injected simultaneously through a single combined nozzle into the mould. As the green and yellow materials flow side by side and into each other, a natural marbled colour effect is created on the part surface. Permanent and visually appealing coloured surfaces are produced in a single cycle — no labels or post-painting required.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
11
Машины для обработки пластикаТермопластавтоматыМашины для литья пластмасс под давлением
Ref. no.: 18617Manufacturer: DEMAGYear of construction: 2007Clamping unitClamping force: 80 tonOpening stroke: 340 mmDistance between tie bars: 370 x 370 mmMould height min.: 150 mmInjection unitScrew diameter: 25 mmInjection volume: 51 cm³Shot weight: 45 gInjection pressure: 2000 barMeasurements and weightDimensions: 4,3 x 1,3 x 2,3 mMachine weight: 4750 kgFurther information:A Technology That Stands Out in Energy Efficiency: Less Energy, Higher PrecisionThe Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.Motor System — Siemens MOTICS 3Main Drive Motor · Water-Cooled Servo MotorThe main drive unit that controls all clamping and injection movements with high precision.Plasticising Motor · Water-Cooled Servo MotorBased on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.5-Axis Full Servo ControlThe machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.NC4 Control SystemThe keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Ref. no.: 18617
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
13
Машины для обработки пластикаТермопластавтоматыМашины для литья пластмасс под давлением
Ref. no.: 18616Manufacturer: DEMAGYear of construction: 2007Clamping unitClamping force: 80 tonOpening stroke: 340 mmDistance between tie bars: 370 x 370 mmMould height min.: 150 mmInjection unitScrew diameter: 25 mmInjection volume: 51 cm³Shot weight: 45 gInjection pressure: 2000 barMeasurements and weightDimensions: 4,3 x 1,3 x 2,3 mMachine weight: 4750 kgFurther information:A Technology That Stands Out in Energy Efficiency: Less Energy, Higher PrecisionThe Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.Motor System — Siemens MOTICS 3Main Drive Motor · Water-Cooled Servo MotorThe main drive unit that controls all clamping and injection movements with high precision.Plasticising Motor · Water-Cooled Servo MotorBased on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.5-Axis Full Servo ControlThe machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.NC4 Control SystemThe keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Ref. no.: 18616
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
13
Машины для обработки пластикаТермопластавтоматыМашины для литья пластмасс под давлением
Ref. no.: 18615Manufacturer: DEMAGYear of construction: 2007Clamping unitClamping force: 80 tonOpening stroke: 340 mmDistance between tie bars: 370 x 370 mmMould height min.: 150 mmInjection unitScrew diameter: 25 mmInjection volume: 51 cm³Shot weight: 45 gInjection pressure: 2000 barMeasurements and weightDimensions: 4,3 x 1,3 x 2,3 mMachine weight: 4750 kgFurther information:A Technology That Stands Out in Energy Efficiency: Less Energy, Higher PrecisionThe Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.Motor System — Siemens MOTICS 3Main Drive Motor · Water-Cooled Servo MotorThe main drive unit that controls all clamping and injection movements with high precision.Plasticising Motor · Water-Cooled Servo MotorBased on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.5-Axis Full Servo ControlThe machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.NC4 Control SystemThe keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Ref. no.: 18615
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
8
Машины для обработки пластикаТермопластавтоматыМашины для литья пластмасс под давлением
Ref. no.: 18614Manufacturer: DEMAGYear of construction: 2006Clamping unitClamping force: 80 tonOpening stroke: 340 mmDistance between tie bars: 370 x 370 mmMould height min.: 150 mmInjection unitScrew diameter: 18 mmInjection volume: 26 cm³Shot weight: 23 gInjection pressure: 2800 barMeasurements and weightDimensions: 4,3 x1,3 x 2,3 mMachine weight: 4750 kgFurther information:A Technology That Stands Out in Energy Efficiency: Less Energy, Higher PrecisionThe Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.Motor System — Siemens MOTICS 3Main Drive Motor · Water-Cooled Servo MotorThe main drive unit that controls all clamping and injection movements with high precision.Plasticising Motor · Water-Cooled Servo MotorBased on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.5-Axis Full Servo ControlThe machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.NC4 Control SystemThe keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Ref. no.: 18614
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 18 mm
Injection volume: 26 cm³
Shot weight: 23 g
Injection pressure: 2800 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 18 mm
Injection volume: 26 cm³
Shot weight: 23 g
Injection pressure: 2800 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
13
Машины для обработки пластикаТермопластавтоматыМашины для литья пластмасс под давлением
Ref. no.: 18613Manufacturer: DEMAGYear of construction: 2006Clamping unitClamping force: 80 tonOpening stroke: 340 mmDistance between tie bars: 370 x 370 mmMould height min.: 150 mmInjection unitScrew diameter: 30 mmInjection volume: 74 cm³Shot weight: 60 gInjection pressure: 1390 barMeasurements and weightDimensions: 4,3 x1,3 x 2,3 mMachine weight: 4750 kgFurther information:A Technology That Stands Out in Energy Efficiency: Less Energy, Higher PrecisionThe Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.Motor System — Siemens MOTICS 3Main Drive Motor · Water-Cooled Servo MotorThe main drive unit that controls all clamping and injection movements with high precision.Plasticising Motor · Water-Cooled Servo MotorBased on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.5-Axis Full Servo ControlThe machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.NC4 Control SystemThe keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Ref. no.: 18613
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 74 cm³
Shot weight: 60 g
Injection pressure: 1390 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 74 cm³
Shot weight: 60 g
Injection pressure: 1390 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
13
Машины для обработки пластикаТермопластавтоматыМашины для литья пластмасс под давлением
Ref. no.: 18612Manufacturer: DEMAGYear of construction: 2006Clamping unitClamping force: 80 tonOpening stroke: 340 mmDistance between tie bars: 370 x 370 mmMould height min.: 150 mmInjection unitScrew diameter: 22 mmInjection volume: 39 cm³Shot weight: 35 gInjection pressure: 2500 barMeasurements and weightDimensions: 4,3 x1,3 x 2,3 mMachine weight: 4750 kgFurther information:A Technology That Stands Out in Energy Efficiency: Less Energy, Higher PrecisionThe Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.Motor System — Siemens MOTICS 3Main Drive Motor · Water-Cooled Servo MotorThe main drive unit that controls all clamping and injection movements with high precision.Plasticising Motor · Water-Cooled Servo MotorBased on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.5-Axis Full Servo ControlThe machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.NC4 Control SystemThe keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Ref. no.: 18612
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 22 mm
Injection volume: 39 cm³
Shot weight: 35 g
Injection pressure: 2500 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 22 mm
Injection volume: 39 cm³
Shot weight: 35 g
Injection pressure: 2500 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
13
Машины для обработки пластикаТермопластавтоматыМашины для литья пластмасс под давлением
Ref. no.: 18138Manufacturer: DEMAGYear of construction: 2006Clamping unitClamping force: 80 tonOpening stroke: 850 mmDistance between tie bars: 370 X 370 mmMould height min.: 200 mmMould height max.: 510 mmPlaten size (h x v): 600 x 600 mmInjection unitScrew diameter: 22 mmInjection volume: 37 cm³Shot weight: 32 gInjection pressure: 2580 barMeasurements and weightDimensions: 4,50 X 1,28 X 1,95 mMachine weight: 4750 kg
Ref. no.: 18138
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 850 mm
Distance between tie bars: 370 X 370 mm
Mould height min.: 200 mm
Mould height max.: 510 mm
Platen size (h x v): 600 x 600 mm
Injection unit
Screw diameter: 22 mm
Injection volume: 37 cm³
Shot weight: 32 g
Injection pressure: 2580 bar
Measurements and weight
Dimensions: 4,50 X 1,28 X 1,95 m
Machine weight: 4750 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 850 mm
Distance between tie bars: 370 X 370 mm
Mould height min.: 200 mm
Mould height max.: 510 mm
Platen size (h x v): 600 x 600 mm
Injection unit
Screw diameter: 22 mm
Injection volume: 37 cm³
Shot weight: 32 g
Injection pressure: 2580 bar
Measurements and weight
Dimensions: 4,50 X 1,28 X 1,95 m
Machine weight: 4750 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
10
Машины для обработки пластикаТермопластавтоматыМашины для литья пластмасс под давлением
Ref. no.: 18625Manufacturer: WITTMANN BATTENFELDYear of construction: 2011Clamping unitClamping force: 110 tonOpening stroke: 380 mmDistance between tie bars: 470 x 420 mmMould height min.: 200 mmMould height max.: 450 mmPlaten size (h x v): 680 x 663 mmInjection unitScrew diameter: 30 mmInjection volume: 88 cm³Shot weight: 80 gInjection pressure: 1471 barMeasurements and weightDimensions: 4,8 x 1,4 x 2,2 mMachine weight: 4600 kgFurther information:Wittmann Battenfeld EcoPower series represents high-efficiency all-electric injection moulding technology designed for precision production and stable processing performance.All major machine movements are driven by servo electric motors. Injection, dosing, clamping and ejector movements are performed completely electrically, ensuring extremely precise motion control, excellent repeatability and stable production quality.Compared to conventional hydraulic injection moulding machines, the EcoPower series can achieve approximately 60% up to 80% energy savings depending on the application. In addition, the machines offer lower heat generation, quiet operation and a cleaner production environment.The integrated UNILOG B6 / B6P control system is well known for its user-friendly operation, reliable process management and stable long-term performance. Combined with high dynamic servo technology and low-vibration operation, the EcoPower platform is especially suitable for technical plastic parts, electronic components, automotive applications and medical production.Today, the Wittmann Battenfeld EcoPower series is still considered one of the most reliable and energy-efficient all-electric injection moulding machine platforms on the market.
Ref. no.: 18625
Manufacturer: WITTMANN BATTENFELD
Year of construction: 2011
Clamping unit
Clamping force: 110 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 450 mm
Platen size (h x v): 680 x 663 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 88 cm³
Shot weight: 80 g
Injection pressure: 1471 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 4600 kg
Further information:
Wittmann Battenfeld EcoPower series represents high-efficiency all-electric injection moulding technology designed for precision production and stable processing performance.
All major machine movements are driven by servo electric motors. Injection, dosing, clamping and ejector movements are performed completely electrically, ensuring extremely precise motion control, excellent repeatability and stable production quality.
Compared to conventional hydraulic injection moulding machines, the EcoPower series can achieve approximately 60% up to 80% energy savings depending on the application. In addition, the machines offer lower heat generation, quiet operation and a cleaner production environment.
The integrated UNILOG B6 / B6P control system is well known for its user-friendly operation, reliable process management and stable long-term performance. Combined with high dynamic servo technology and low-vibration operation, the EcoPower platform is especially suitable for technical plastic parts, electronic components, automotive applications and medical production.
Today, the Wittmann Battenfeld EcoPower series is still considered one of the most reliable and energy-efficient all-electric injection moulding machine platforms on the market.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: WITTMANN BATTENFELD
Year of construction: 2011
Clamping unit
Clamping force: 110 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 450 mm
Platen size (h x v): 680 x 663 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 88 cm³
Shot weight: 80 g
Injection pressure: 1471 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 4600 kg
Further information:
Wittmann Battenfeld EcoPower series represents high-efficiency all-electric injection moulding technology designed for precision production and stable processing performance.
All major machine movements are driven by servo electric motors. Injection, dosing, clamping and ejector movements are performed completely electrically, ensuring extremely precise motion control, excellent repeatability and stable production quality.
Compared to conventional hydraulic injection moulding machines, the EcoPower series can achieve approximately 60% up to 80% energy savings depending on the application. In addition, the machines offer lower heat generation, quiet operation and a cleaner production environment.
The integrated UNILOG B6 / B6P control system is well known for its user-friendly operation, reliable process management and stable long-term performance. Combined with high dynamic servo technology and low-vibration operation, the EcoPower platform is especially suitable for technical plastic parts, electronic components, automotive applications and medical production.
Today, the Wittmann Battenfeld EcoPower series is still considered one of the most reliable and energy-efficient all-electric injection moulding machine platforms on the market.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
11
Машины для обработки пластикаТермопластавтоматыМашины для литья пластмасс под давлением
Ref. no.: 18624Manufacturer: WITTMANN BATTENFELDYear of construction: 2010Clamping unitClamping force: 180 tonOpening stroke: 480 mmDistance between tie bars: 570 x 520 mmMould height min.: 225 mmMould height max.: 550 mmPlaten size (h x v): 810 x 805 mmInjection unitScrew diameter: 35 mmInjection volume: 168 cm³Shot weight: 163 gInjection pressure: 2083 barMeasurements and weightDimensions: 5,2 x 1,6 x 2,2 mMachine weight: 6800 kgFurther information:Die Wittmann Battenfeld EcoPower Serie steht für hocheffiziente vollelektrische Spritzgießtechnologie, entwickelt für präzise Produktionsprozesse und stabile Fertigungsbedingungen.Alle Hauptbewegungen der Maschine werden durch Servo-Elektromotoren angetrieben. Einspritzen, Dosieren, Schließen und Auswerfen erfolgen vollständig elektrisch und ermöglichen dadurch eine äußerst präzise Bewegungssteuerung, hohe Wiederholgenauigkeit und stabile Produktionsqualität.Im Vergleich zu konventionellen hydraulischen Spritzgießmaschinen kann die EcoPower Serie – abhängig von der Anwendung – Energieeinsparungen von ca. 60% bis 80% erreichen. Zusätzlich bieten die Maschinen eine reduzierte Wärmeentwicklung, einen ruhigen Lauf sowie eine saubere Produktionsumgebung.Die integrierte UNILOG B6 / B6P Steuerung ist bekannt für ihre benutzerfreundliche Bedienung, zuverlässige Prozesskontrolle und stabile Langzeitleistung. In Kombination mit der hochdynamischen Servotechnologie und dem vibrationsarmen Betrieb eignet sich die EcoPower Plattform besonders für technische Kunststoffteile, elektronische Komponenten, Automobilanwendungen und medizinische Produktionen.Die Wittmann Battenfeld EcoPower Serie zählt auch heute noch zu den zuverlässigsten und energieeffizientesten vollelektrischen Spritzgießmaschinenplattformen auf dem Markt.
Ref. no.: 18624
Manufacturer: WITTMANN BATTENFELD
Year of construction: 2010
Clamping unit
Clamping force: 180 ton
Opening stroke: 480 mm
Distance between tie bars: 570 x 520 mm
Mould height min.: 225 mm
Mould height max.: 550 mm
Platen size (h x v): 810 x 805 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 168 cm³
Shot weight: 163 g
Injection pressure: 2083 bar
Measurements and weight
Dimensions: 5,2 x 1,6 x 2,2 m
Machine weight: 6800 kg
Further information:
Die Wittmann Battenfeld EcoPower Serie steht für hocheffiziente vollelektrische Spritzgießtechnologie, entwickelt für präzise Produktionsprozesse und stabile Fertigungsbedingungen.
Alle Hauptbewegungen der Maschine werden durch Servo-Elektromotoren angetrieben. Einspritzen, Dosieren, Schließen und Auswerfen erfolgen vollständig elektrisch und ermöglichen dadurch eine äußerst präzise Bewegungssteuerung, hohe Wiederholgenauigkeit und stabile Produktionsqualität.
Im Vergleich zu konventionellen hydraulischen Spritzgießmaschinen kann die EcoPower Serie – abhängig von der Anwendung – Energieeinsparungen von ca. 60% bis 80% erreichen. Zusätzlich bieten die Maschinen eine reduzierte Wärmeentwicklung, einen ruhigen Lauf sowie eine saubere Produktionsumgebung.
Die integrierte UNILOG B6 / B6P Steuerung ist bekannt für ihre benutzerfreundliche Bedienung, zuverlässige Prozesskontrolle und stabile Langzeitleistung. In Kombination mit der hochdynamischen Servotechnologie und dem vibrationsarmen Betrieb eignet sich die EcoPower Plattform besonders für technische Kunststoffteile, elektronische Komponenten, Automobilanwendungen und medizinische Produktionen.
Die Wittmann Battenfeld EcoPower Serie zählt auch heute noch zu den zuverlässigsten und energieeffizientesten vollelektrischen Spritzgießmaschinenplattformen auf dem Markt.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: WITTMANN BATTENFELD
Year of construction: 2010
Clamping unit
Clamping force: 180 ton
Opening stroke: 480 mm
Distance between tie bars: 570 x 520 mm
Mould height min.: 225 mm
Mould height max.: 550 mm
Platen size (h x v): 810 x 805 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 168 cm³
Shot weight: 163 g
Injection pressure: 2083 bar
Measurements and weight
Dimensions: 5,2 x 1,6 x 2,2 m
Machine weight: 6800 kg
Further information:
Die Wittmann Battenfeld EcoPower Serie steht für hocheffiziente vollelektrische Spritzgießtechnologie, entwickelt für präzise Produktionsprozesse und stabile Fertigungsbedingungen.
Alle Hauptbewegungen der Maschine werden durch Servo-Elektromotoren angetrieben. Einspritzen, Dosieren, Schließen und Auswerfen erfolgen vollständig elektrisch und ermöglichen dadurch eine äußerst präzise Bewegungssteuerung, hohe Wiederholgenauigkeit und stabile Produktionsqualität.
Im Vergleich zu konventionellen hydraulischen Spritzgießmaschinen kann die EcoPower Serie – abhängig von der Anwendung – Energieeinsparungen von ca. 60% bis 80% erreichen. Zusätzlich bieten die Maschinen eine reduzierte Wärmeentwicklung, einen ruhigen Lauf sowie eine saubere Produktionsumgebung.
Die integrierte UNILOG B6 / B6P Steuerung ist bekannt für ihre benutzerfreundliche Bedienung, zuverlässige Prozesskontrolle und stabile Langzeitleistung. In Kombination mit der hochdynamischen Servotechnologie und dem vibrationsarmen Betrieb eignet sich die EcoPower Plattform besonders für technische Kunststoffteile, elektronische Komponenten, Automobilanwendungen und medizinische Produktionen.
Die Wittmann Battenfeld EcoPower Serie zählt auch heute noch zu den zuverlässigsten und energieeffizientesten vollelektrischen Spritzgießmaschinenplattformen auf dem Markt.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
8
Машины для обработки пластикаТермопластавтоматыМашины для литья пластмасс под давлением
Ref. no.: 18623Manufacturer: WITTMANN BATTENFELDYear of construction: 2010Clamping unitClamping force: 180 tonOpening stroke: 480 mmDistance between tie bars: 570 x 520 mmMould height min.: 225 mmMould height max.: 550 mmPlaten size (h x v): 810 x 805 mmInjection unitScrew diameter: 30 mmInjection volume: 124 cm³Shot weight: 120 gInjection pressure: 2823 barMeasurements and weightDimensions: 4,8 x 1,6 x 2,2 mMachine weight: 6800 kgFurther information:Die Wittmann Battenfeld EcoPower Serie steht für hocheffiziente vollelektrische Spritzgießtechnologie, entwickelt für präzise Produktionsprozesse und stabile Fertigungsbedingungen.Alle Hauptbewegungen der Maschine werden durch Servo-Elektromotoren angetrieben. Einspritzen, Dosieren, Schließen und Auswerfen erfolgen vollständig elektrisch und ermöglichen dadurch eine äußerst präzise Bewegungssteuerung, hohe Wiederholgenauigkeit und stabile Produktionsqualität.Im Vergleich zu konventionellen hydraulischen Spritzgießmaschinen kann die EcoPower Serie – abhängig von der Anwendung – Energieeinsparungen von ca. 60% bis 80% erreichen. Zusätzlich bieten die Maschinen eine reduzierte Wärmeentwicklung, einen ruhigen Lauf sowie eine saubere Produktionsumgebung.Die integrierte UNILOG B6 / B6P Steuerung ist bekannt für ihre benutzerfreundliche Bedienung, zuverlässige Prozesskontrolle und stabile Langzeitleistung. In Kombination mit der hochdynamischen Servotechnologie und dem vibrationsarmen Betrieb eignet sich die EcoPower Plattform besonders für technische Kunststoffteile, elektronische Komponenten, Automobilanwendungen und medizinische Produktionen.Die Wittmann Battenfeld EcoPower Serie zählt auch heute noch zu den zuverlässigsten und energieeffizientesten vollelektrischen Spritzgießmaschinenplattformen auf dem Markt.
Ref. no.: 18623
Manufacturer: WITTMANN BATTENFELD
Year of construction: 2010
Clamping unit
Clamping force: 180 ton
Opening stroke: 480 mm
Distance between tie bars: 570 x 520 mm
Mould height min.: 225 mm
Mould height max.: 550 mm
Platen size (h x v): 810 x 805 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 124 cm³
Shot weight: 120 g
Injection pressure: 2823 bar
Measurements and weight
Dimensions: 4,8 x 1,6 x 2,2 m
Machine weight: 6800 kg
Further information:
Die Wittmann Battenfeld EcoPower Serie steht für hocheffiziente vollelektrische Spritzgießtechnologie, entwickelt für präzise Produktionsprozesse und stabile Fertigungsbedingungen.
Alle Hauptbewegungen der Maschine werden durch Servo-Elektromotoren angetrieben. Einspritzen, Dosieren, Schließen und Auswerfen erfolgen vollständig elektrisch und ermöglichen dadurch eine äußerst präzise Bewegungssteuerung, hohe Wiederholgenauigkeit und stabile Produktionsqualität.
Im Vergleich zu konventionellen hydraulischen Spritzgießmaschinen kann die EcoPower Serie – abhängig von der Anwendung – Energieeinsparungen von ca. 60% bis 80% erreichen. Zusätzlich bieten die Maschinen eine reduzierte Wärmeentwicklung, einen ruhigen Lauf sowie eine saubere Produktionsumgebung.
Die integrierte UNILOG B6 / B6P Steuerung ist bekannt für ihre benutzerfreundliche Bedienung, zuverlässige Prozesskontrolle und stabile Langzeitleistung. In Kombination mit der hochdynamischen Servotechnologie und dem vibrationsarmen Betrieb eignet sich die EcoPower Plattform besonders für technische Kunststoffteile, elektronische Komponenten, Automobilanwendungen und medizinische Produktionen.
Die Wittmann Battenfeld EcoPower Serie zählt auch heute noch zu den zuverlässigsten und energieeffizientesten vollelektrischen Spritzgießmaschinenplattformen auf dem Markt.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: WITTMANN BATTENFELD
Year of construction: 2010
Clamping unit
Clamping force: 180 ton
Opening stroke: 480 mm
Distance between tie bars: 570 x 520 mm
Mould height min.: 225 mm
Mould height max.: 550 mm
Platen size (h x v): 810 x 805 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 124 cm³
Shot weight: 120 g
Injection pressure: 2823 bar
Measurements and weight
Dimensions: 4,8 x 1,6 x 2,2 m
Machine weight: 6800 kg
Further information:
Die Wittmann Battenfeld EcoPower Serie steht für hocheffiziente vollelektrische Spritzgießtechnologie, entwickelt für präzise Produktionsprozesse und stabile Fertigungsbedingungen.
Alle Hauptbewegungen der Maschine werden durch Servo-Elektromotoren angetrieben. Einspritzen, Dosieren, Schließen und Auswerfen erfolgen vollständig elektrisch und ermöglichen dadurch eine äußerst präzise Bewegungssteuerung, hohe Wiederholgenauigkeit und stabile Produktionsqualität.
Im Vergleich zu konventionellen hydraulischen Spritzgießmaschinen kann die EcoPower Serie – abhängig von der Anwendung – Energieeinsparungen von ca. 60% bis 80% erreichen. Zusätzlich bieten die Maschinen eine reduzierte Wärmeentwicklung, einen ruhigen Lauf sowie eine saubere Produktionsumgebung.
Die integrierte UNILOG B6 / B6P Steuerung ist bekannt für ihre benutzerfreundliche Bedienung, zuverlässige Prozesskontrolle und stabile Langzeitleistung. In Kombination mit der hochdynamischen Servotechnologie und dem vibrationsarmen Betrieb eignet sich die EcoPower Plattform besonders für technische Kunststoffteile, elektronische Komponenten, Automobilanwendungen und medizinische Produktionen.
Die Wittmann Battenfeld EcoPower Serie zählt auch heute noch zu den zuverlässigsten und energieeffizientesten vollelektrischen Spritzgießmaschinenplattformen auf dem Markt.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
_thumb.png "Показывать рекламу")
8
Машины для обработки пластикаРоботы
Ref. no.: 18635Manufacturer: SEPROYear of construction: 2022Further information:SEPRO S5-25 med – 3-Axis Servo Linear Robot* Manufacturer: SEPRO Robotique S.A.S. (France)* Model: S5-25 med* Year of manufacture: 2022* Serial number: R015336-02* Condition: Very good and clean condition* Application: Injection moulding automation / part removal robotTechnical SpecificationsDescription ValueRobot type 3-axis servo linear robotX-axis (Traverse) 2000 mmY-axis 700 mmVertical stroke 1200 mmRotation No rotationPayload class approx. 10 kgControl system SEPRO Visual 2Voltage 3x400V – 3x480VFrequency 50/60 HzMax. power 1.5 kVAWeight approx. 100 kgSeries S5 medDescriptionThe SEPRO S5-25 med is a high-performance 3-axis servo linear robot designed for automated part removal and handling applications on injection moulding machines.The robot is in very good technical and visual condition and comes from a clean production environment. The “med” version is particularly suitable for medical and clean-room applications.The robot has only been used for testing and training purposes.The system offers:* fast and precise movements* reliable servo technology* compact and stable construction* modern SEPRO Visual control system* ideal integration into injection moulding automation systemsSuitable for:* plastic injection moulding machines* medical production* clean-room applications* automated pick & place systems* high-speed handling applications
Ref. no.: 18635
Manufacturer: SEPRO
Year of construction: 2022
Further information:
SEPRO S5-25 med – 3-Axis Servo Linear Robot
* Manufacturer: SEPRO Robotique S.A.S. (France)
* Model: S5-25 med
* Year of manufacture: 2022
* Serial number: R015336-02
* Condition: Very good and clean condition
* Application: Injection moulding automation / part removal robot
Technical Specifications
Description Value
Robot type 3-axis servo linear robot
X-axis (Traverse) 2000 mm
Y-axis 700 mm
Vertical stroke 1200 mm
Rotation No rotation
Payload class approx. 10 kg
Control system SEPRO Visual 2
Voltage 3x400V – 3x480V
Frequency 50/60 Hz
Max. power 1.5 kVA
Weight approx. 100 kg
Series S5 med
Description
The SEPRO S5-25 med is a high-performance 3-axis servo linear robot designed for automated part removal and handling applications on injection moulding machines.
The robot is in very good technical and visual condition and comes from a clean production environment. The “med” version is particularly suitable for medical and clean-room applications.
The robot has only been used for testing and training purposes.
The system offers:
* fast and precise movements
* reliable servo technology
* compact and stable construction
* modern SEPRO Visual control system
* ideal integration into injection moulding automation systems
Suitable for:
* plastic injection moulding machines
* medical production
* clean-room applications
* automated pick & place systems
* high-speed handling applications
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: SEPRO
Year of construction: 2022
Further information:
SEPRO S5-25 med – 3-Axis Servo Linear Robot
* Manufacturer: SEPRO Robotique S.A.S. (France)
* Model: S5-25 med
* Year of manufacture: 2022
* Serial number: R015336-02
* Condition: Very good and clean condition
* Application: Injection moulding automation / part removal robot
Technical Specifications
Description Value
Robot type 3-axis servo linear robot
X-axis (Traverse) 2000 mm
Y-axis 700 mm
Vertical stroke 1200 mm
Rotation No rotation
Payload class approx. 10 kg
Control system SEPRO Visual 2
Voltage 3x400V – 3x480V
Frequency 50/60 Hz
Max. power 1.5 kVA
Weight approx. 100 kg
Series S5 med
Description
The SEPRO S5-25 med is a high-performance 3-axis servo linear robot designed for automated part removal and handling applications on injection moulding machines.
The robot is in very good technical and visual condition and comes from a clean production environment. The “med” version is particularly suitable for medical and clean-room applications.
The robot has only been used for testing and training purposes.
The system offers:
* fast and precise movements
* reliable servo technology
* compact and stable construction
* modern SEPRO Visual control system
* ideal integration into injection moulding automation systems
Suitable for:
* plastic injection moulding machines
* medical production
* clean-room applications
* automated pick & place systems
* high-speed handling applications
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
13
Фасовочное оборудованиеУпаковочные машиныФасовочное оборудование
Ref. no.: 18592Manufacturer: SEALPACYear of construction: 2013Further information:TECHNICAL DATAFeature SpecificationManufacturer SEALPAC GmbHModel SEALPAC A5Machine Type Tray Sealer / SchalenverschließanlageSerial Number A5-01-2661Year of Manufacture 2013Electrical Connection 3 x 400 / 230 VFrequency 50–60 HzInstalled Power max. 8 kWMachine Weight approx. 1,600 kgControl System Touchscreen control panelConstruction Stainless steelWorking Environment Cleanroom / Clean roomApplication Areas Medical / Food / Technical packagingSEALPAC A5 Tray SealerUsed – Excellent Condition – From Cleanroom ProductionPreviously used for cleanroom packaging of medical and laboratory consumables, including pipette tip racks.This high-quality SEALPAC A5 tray sealing machine is designed for professional packaging applications where hygiene, reliability and process stability are essential.The machine was previously operated in a cleanroom environment, making it particularly suitable for medical, laboratory and sensitive packaging applications. Thanks to its stainless steel construction, compact design and user-friendly control system, the machine offers reliable and efficient production performance.As visible in the photos, the machine is in very clean and well-maintained condition.General ConditionThe machine is currently dismantled and stored. Visual condition is very clean and the machine was previously used in a professional production environment.
Ref. no.: 18592
Manufacturer: SEALPAC
Year of construction: 2013
Further information:
TECHNICAL DATA
Feature Specification
Manufacturer SEALPAC GmbH
Model SEALPAC A5
Machine Type Tray Sealer / Schalenverschließanlage
Serial Number A5-01-2661
Year of Manufacture 2013
Electrical Connection 3 x 400 / 230 V
Frequency 50–60 Hz
Installed Power max. 8 kW
Machine Weight approx. 1,600 kg
Control System Touchscreen control panel
Construction Stainless steel
Working Environment Cleanroom / Clean room
Application Areas Medical / Food / Technical packaging
SEALPAC A5 Tray Sealer
Used – Excellent Condition – From Cleanroom Production
Previously used for cleanroom packaging of medical and laboratory consumables, including pipette tip racks.
This high-quality SEALPAC A5 tray sealing machine is designed for professional packaging applications where hygiene, reliability and process stability are essential.
The machine was previously operated in a cleanroom environment, making it particularly suitable for medical, laboratory and sensitive packaging applications. Thanks to its stainless steel construction, compact design and user-friendly control system, the machine offers reliable and efficient production performance.
As visible in the photos, the machine is in very clean and well-maintained condition.
General Condition
The machine is currently dismantled and stored. Visual condition is very clean and the machine was previously used in a professional production environment.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: SEALPAC
Year of construction: 2013
Further information:
TECHNICAL DATA
Feature Specification
Manufacturer SEALPAC GmbH
Model SEALPAC A5
Machine Type Tray Sealer / Schalenverschließanlage
Serial Number A5-01-2661
Year of Manufacture 2013
Electrical Connection 3 x 400 / 230 V
Frequency 50–60 Hz
Installed Power max. 8 kW
Machine Weight approx. 1,600 kg
Control System Touchscreen control panel
Construction Stainless steel
Working Environment Cleanroom / Clean room
Application Areas Medical / Food / Technical packaging
SEALPAC A5 Tray Sealer
Used – Excellent Condition – From Cleanroom Production
Previously used for cleanroom packaging of medical and laboratory consumables, including pipette tip racks.
This high-quality SEALPAC A5 tray sealing machine is designed for professional packaging applications where hygiene, reliability and process stability are essential.
The machine was previously operated in a cleanroom environment, making it particularly suitable for medical, laboratory and sensitive packaging applications. Thanks to its stainless steel construction, compact design and user-friendly control system, the machine offers reliable and efficient production performance.
As visible in the photos, the machine is in very clean and well-maintained condition.
General Condition
The machine is currently dismantled and stored. Visual condition is very clean and the machine was previously used in a professional production environment.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
13
Машины для обработки пластикаПериферийные устройства
Ref. no.: 18439Manufacturer: MOTANYear of construction: 1995Further information:MOTAN Central Drying & Vacuum Conveying SystemComplete MOTAN central drying and automatic material conveying system for plastic injection molding applications.The system includes:* 15 pcs stainless steel drying hoppers* Hopper capacity: 60 liters eachThe system was used in technical plastics production and is suitable for processing hygroscopic materials such as:PA, PC, PET, PBT, ABS, TPU and other engineering plastics.System Components1. MOTAN ADC 200/10 Dry Air Generator* Year of manufacture: 1995* Dry air capacity: approx. 200 m³/h* Heating power: approx. 19.5 kW* Central dry air generation system* Desiccant drying technologyFunction:Provides low-humidity hot air for the drying hoppers.2. MOTAN LA net 200 Central Control System* Year of manufacture: 2006* Central process and automation control unit* Touchscreen operator panel* Drying and conveying process management* Alarm and monitoring functionsFunction:Central control of all drying, conveying and material distribution processes.3. Drying Hoppers* 15 pcs stainless steel drying hoppers* Hopper volume: 60 liters each* Central dry air connection* Automatic material loading* Suitable for technical plastics drying4. Central Vacuum Conveying System* Elmo Rietschle central vacuum pump* Automatic granule conveying system* Central material distribution* Multi-machine supply capability5. Stainless Steel Piping & Filter System* Central conveying pipework* Filter units* Material loaders* Automatic distribution stationWorking PrinciplePlastic granules are automatically conveyed through the central vacuum system into the drying hoppers.The MOTAN ADC 200/10 dry air generator produces low-humidity hot air which continuously circulates through the material inside the hoppers.During this process, moisture is removed from the plastic granules to prepare the material for injection molding production.After drying, the material is automatically transported through the central conveying lines and distributed to the connected injection molding machines.All drying and conveying processes are centrally controlled via the MOTAN LA net 200 control systemConditionThe system was in production operation until dismantling.Further technical information, photos and videos available on request.
Ref. no.: 18439
Manufacturer: MOTAN
Year of construction: 1995
Further information:
MOTAN Central Drying & Vacuum Conveying System
Complete MOTAN central drying and automatic material conveying system for plastic injection molding applications.
The system includes:
* 15 pcs stainless steel drying hoppers
* Hopper capacity: 60 liters each
The system was used in technical plastics production and is suitable for processing hygroscopic materials such as:
PA, PC, PET, PBT, ABS, TPU and other engineering plastics.
System Components
1. MOTAN ADC 200/10 Dry Air Generator
* Year of manufacture: 1995
* Dry air capacity: approx. 200 m³/h
* Heating power: approx. 19.5 kW
* Central dry air generation system
* Desiccant drying technology
Function:
Provides low-humidity hot air for the drying hoppers.
2. MOTAN LA net 200 Central Control System
* Year of manufacture: 2006
* Central process and automation control unit
* Touchscreen operator panel
* Drying and conveying process management
* Alarm and monitoring functions
Function:
Central control of all drying, conveying and material distribution processes.
3. Drying Hoppers
* 15 pcs stainless steel drying hoppers
* Hopper volume: 60 liters each
* Central dry air connection
* Automatic material loading
* Suitable for technical plastics drying
4. Central Vacuum Conveying System
* Elmo Rietschle central vacuum pump
* Automatic granule conveying system
* Central material distribution
* Multi-machine supply capability
5. Stainless Steel Piping & Filter System
* Central conveying pipework
* Filter units
* Material loaders
* Automatic distribution station
Working Principle
Plastic granules are automatically conveyed through the central vacuum system into the drying hoppers.
The MOTAN ADC 200/10 dry air generator produces low-humidity hot air which continuously circulates through the material inside the hoppers.
During this process, moisture is removed from the plastic granules to prepare the material for injection molding production.
After drying, the material is automatically transported through the central conveying lines and distributed to the connected injection molding machines.
All drying and conveying processes are centrally controlled via the MOTAN LA net 200 control system
Condition
The system was in production operation until dismantling.
Further technical information, photos and videos available on request.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: MOTAN
Year of construction: 1995
Further information:
MOTAN Central Drying & Vacuum Conveying System
Complete MOTAN central drying and automatic material conveying system for plastic injection molding applications.
The system includes:
* 15 pcs stainless steel drying hoppers
* Hopper capacity: 60 liters each
The system was used in technical plastics production and is suitable for processing hygroscopic materials such as:
PA, PC, PET, PBT, ABS, TPU and other engineering plastics.
System Components
1. MOTAN ADC 200/10 Dry Air Generator
* Year of manufacture: 1995
* Dry air capacity: approx. 200 m³/h
* Heating power: approx. 19.5 kW
* Central dry air generation system
* Desiccant drying technology
Function:
Provides low-humidity hot air for the drying hoppers.
2. MOTAN LA net 200 Central Control System
* Year of manufacture: 2006
* Central process and automation control unit
* Touchscreen operator panel
* Drying and conveying process management
* Alarm and monitoring functions
Function:
Central control of all drying, conveying and material distribution processes.
3. Drying Hoppers
* 15 pcs stainless steel drying hoppers
* Hopper volume: 60 liters each
* Central dry air connection
* Automatic material loading
* Suitable for technical plastics drying
4. Central Vacuum Conveying System
* Elmo Rietschle central vacuum pump
* Automatic granule conveying system
* Central material distribution
* Multi-machine supply capability
5. Stainless Steel Piping & Filter System
* Central conveying pipework
* Filter units
* Material loaders
* Automatic distribution station
Working Principle
Plastic granules are automatically conveyed through the central vacuum system into the drying hoppers.
The MOTAN ADC 200/10 dry air generator produces low-humidity hot air which continuously circulates through the material inside the hoppers.
During this process, moisture is removed from the plastic granules to prepare the material for injection molding production.
After drying, the material is automatically transported through the central conveying lines and distributed to the connected injection molding machines.
All drying and conveying processes are centrally controlled via the MOTAN LA net 200 control system
Condition
The system was in production operation until dismantling.
Further technical information, photos and videos available on request.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
13
Машины для обработки пластикаТермопластавтоматыМашины для литья пластмасс под давлением
Ref. no.: 18622Manufacturer: DEMAGYear of construction: 2008Clamping unitClamping force: 100 tonOpening stroke: 380 mmDistance between tie bars: 470 x 420 mmMould height min.: 200 mmMould height max.: 430 mmPlaten size (h x v): 690 x 620 mmInjection unitScrew diameter: 35 mmInjection volume: 115 cm³Shot weight: 103 gInjection pressure: 1600 barMeasurements and weightDimensions: 4,8 x 1,4 x 2,2 mMachine weight: 5500 kgAdditional information & extrasCore pull: 1 pcsFurther information:The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.Key advantages of the IntElect series:* All-electric direct-drive servo technology* Extremely low energy consumption* High precision and process repeatability* Quiet and low-vibration operation* High dynamic servo performance* Low maintenance requirements* Clean production environment* Ideal solution for technical and precision plastic parts* Suitable for high-speed serial productionThe Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Ref. no.: 18622
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 115 cm³
Shot weight: 103 g
Injection pressure: 1600 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Additional information & extras
Core pull: 1 pcs
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 115 cm³
Shot weight: 103 g
Injection pressure: 1600 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Additional information & extras
Core pull: 1 pcs
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
12
Машины для обработки пластикаТермопластавтоматыМашины для литья пластмасс под давлением
Ref. no.: 18621Manufacturer: DEMAGYear of construction: 2008Clamping unitClamping force: 100 tonOpening stroke: 380 mmDistance between tie bars: 470 x 420 mmMould height min.: 200 mmMould height max.: 430 mmPlaten size (h x v): 690 x 620 mmInjection unitScrew diameter: 35 mmInjection volume: 115 cm³Shot weight: 103 gInjection pressure: 1600 barMeasurements and weightDimensions: 4,8 x 1,4 x 2,2 mMachine weight: 5500 kgFurther information:The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.Key advantages of the IntElect series:* All-electric direct-drive servo technology* Extremely low energy consumption* High precision and process repeatability* Quiet and low-vibration operation* High dynamic servo performance* Low maintenance requirements* Clean production environment* Ideal solution for technical and precision plastic parts* Suitable for high-speed serial productionThe Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Ref. no.: 18621
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 115 cm³
Shot weight: 103 g
Injection pressure: 1600 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 115 cm³
Shot weight: 103 g
Injection pressure: 1600 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
10
Машины для обработки пластикаТермопластавтоматыМашины для литья пластмасс под давлением
Ref. no.: 18620Manufacturer: DEMAGYear of construction: 2008Clamping unitClamping force: 100 tonOpening stroke: 380 mmDistance between tie bars: 470 x 420 mmMould height min.: 200 mmMould height max.: 430 mmPlaten size (h x v): 690 x 620 mmInjection unitScrew diameter: 30 mmInjection volume: 85 cm³Shot weight: 76 gInjection pressure: 2180 barMeasurements and weightDimensions: 4,8 x 1,4 x 2,2 mMachine weight: 5500 kgFurther information:The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.Key advantages of the IntElect series:* All-electric direct-drive servo technology* Extremely low energy consumption* High precision and process repeatability* Quiet and low-vibration operation* High dynamic servo performance* Low maintenance requirements* Clean production environment* Ideal solution for technical and precision plastic parts* Suitable for high-speed serial productionThe Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Ref. no.: 18620
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 85 cm³
Shot weight: 76 g
Injection pressure: 2180 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 85 cm³
Shot weight: 76 g
Injection pressure: 2180 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
9
Машины для обработки пластикаТермопластавтоматыМашины для литья пластмасс под давлением
Ref. no.: 18619Manufacturer: DEMAGYear of construction: 2008Clamping unitClamping force: 100 tonOpening stroke: 380 mmDistance between tie bars: 470 x 420 mmMould height min.: 200 mmMould height max.: 430 mmPlaten size (h x v): 690 x 620 mmInjection unitScrew diameter: 30 mmInjection volume: 85 cm³Shot weight: 76 gInjection pressure: 2180 barMeasurements and weightDimensions: 4,8 x 1,4 x 2,2 mMachine weight: 5500 kgFurther information:Die Sumitomo (SHI) Demag IntElect Serie gehört zu den hochpräzisen vollelektrischen Spritzgießmaschinen, die speziell für technische Kunststoffteile, Automobilanwendungen, elektronische Komponenten sowie anspruchsvolle Serienproduktionen entwickelt wurden.Alle Hauptbewegungen der Maschine werden über Direct-Drive Servo-Elektromotoren angetrieben. Einspritzen, Dosieren, Werkzeugbewegungen sowie Auswerferfunktionen erfolgen vollständig elektrisch und ermöglichen dadurch höchste Präzision, ausgezeichnete Wiederholgenauigkeit und maximale Prozessstabilität.Die IntElect Serie ist besonders bekannt für ihren niedrigen Energieverbrauch und ihre hohe Produktionspräzision. Im Vergleich zu konventionellen hydraulischen Spritzgießmaschinen können – abhängig von der Anwendung – Energieeinsparungen von ca. 60 % bis zu 80 % erzielt werden. Gleichzeitig reduziert die geringe Wärmeentwicklung den Kühlbedarf und senkt die gesamten Betriebskosten.Die Maschine verfügt über ein direktes Servo-Einspritz- und Dosiersystem, das sehr schnelle Reaktionszeiten und eine hochpräzise Einspritzsteuerung ermöglicht. Die Spritzeinheit ist mit 4 Heizzonen ausgestattet und sorgt dadurch für eine homogene Plastifizierung sowie stabile Prozessbedingungen, insbesondere bei technischen Kunststoffen.Die wichtigsten Vorteile der IntElect Serie:* Vollelektrische Direct-Drive Servo-Technologie* Sehr geringer Energieverbrauch* Hohe Präzision und Prozesswiederholgenauigkeit* Geräuscharmer und vibrationsarmer Betrieb* Hohe dynamische Servo-Performance* Geringer Wartungsaufwand* Saubere Produktionsumgebung* Ideale Lösung für technische und Präzisionsteile* Geeignet für schnelle SerienproduktionenDie Sumitomo Demag IntElect Serie zählt aufgrund ihrer langen Lebensdauer, stabilen Produktionsleistung und hohen Energieeffizienz auch heute noch zu den gefragtesten vollelektrischen Spritzgießmaschinen am Markt.
Ref. no.: 18619
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 85 cm³
Shot weight: 76 g
Injection pressure: 2180 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Further information:
Die Sumitomo (SHI) Demag IntElect Serie gehört zu den hochpräzisen vollelektrischen Spritzgießmaschinen, die speziell für technische Kunststoffteile, Automobilanwendungen, elektronische Komponenten sowie anspruchsvolle Serienproduktionen entwickelt wurden.
Alle Hauptbewegungen der Maschine werden über Direct-Drive Servo-Elektromotoren angetrieben. Einspritzen, Dosieren, Werkzeugbewegungen sowie Auswerferfunktionen erfolgen vollständig elektrisch und ermöglichen dadurch höchste Präzision, ausgezeichnete Wiederholgenauigkeit und maximale Prozessstabilität.
Die IntElect Serie ist besonders bekannt für ihren niedrigen Energieverbrauch und ihre hohe Produktionspräzision. Im Vergleich zu konventionellen hydraulischen Spritzgießmaschinen können – abhängig von der Anwendung – Energieeinsparungen von ca. 60 % bis zu 80 % erzielt werden. Gleichzeitig reduziert die geringe Wärmeentwicklung den Kühlbedarf und senkt die gesamten Betriebskosten.
Die Maschine verfügt über ein direktes Servo-Einspritz- und Dosiersystem, das sehr schnelle Reaktionszeiten und eine hochpräzise Einspritzsteuerung ermöglicht. Die Spritzeinheit ist mit 4 Heizzonen ausgestattet und sorgt dadurch für eine homogene Plastifizierung sowie stabile Prozessbedingungen, insbesondere bei technischen Kunststoffen.
Die wichtigsten Vorteile der IntElect Serie:
* Vollelektrische Direct-Drive Servo-Technologie
* Sehr geringer Energieverbrauch
* Hohe Präzision und Prozesswiederholgenauigkeit
* Geräuscharmer und vibrationsarmer Betrieb
* Hohe dynamische Servo-Performance
* Geringer Wartungsaufwand
* Saubere Produktionsumgebung
* Ideale Lösung für technische und Präzisionsteile
* Geeignet für schnelle Serienproduktionen
Die Sumitomo Demag IntElect Serie zählt aufgrund ihrer langen Lebensdauer, stabilen Produktionsleistung und hohen Energieeffizienz auch heute noch zu den gefragtesten vollelektrischen Spritzgießmaschinen am Markt.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 85 cm³
Shot weight: 76 g
Injection pressure: 2180 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Further information:
Die Sumitomo (SHI) Demag IntElect Serie gehört zu den hochpräzisen vollelektrischen Spritzgießmaschinen, die speziell für technische Kunststoffteile, Automobilanwendungen, elektronische Komponenten sowie anspruchsvolle Serienproduktionen entwickelt wurden.
Alle Hauptbewegungen der Maschine werden über Direct-Drive Servo-Elektromotoren angetrieben. Einspritzen, Dosieren, Werkzeugbewegungen sowie Auswerferfunktionen erfolgen vollständig elektrisch und ermöglichen dadurch höchste Präzision, ausgezeichnete Wiederholgenauigkeit und maximale Prozessstabilität.
Die IntElect Serie ist besonders bekannt für ihren niedrigen Energieverbrauch und ihre hohe Produktionspräzision. Im Vergleich zu konventionellen hydraulischen Spritzgießmaschinen können – abhängig von der Anwendung – Energieeinsparungen von ca. 60 % bis zu 80 % erzielt werden. Gleichzeitig reduziert die geringe Wärmeentwicklung den Kühlbedarf und senkt die gesamten Betriebskosten.
Die Maschine verfügt über ein direktes Servo-Einspritz- und Dosiersystem, das sehr schnelle Reaktionszeiten und eine hochpräzise Einspritzsteuerung ermöglicht. Die Spritzeinheit ist mit 4 Heizzonen ausgestattet und sorgt dadurch für eine homogene Plastifizierung sowie stabile Prozessbedingungen, insbesondere bei technischen Kunststoffen.
Die wichtigsten Vorteile der IntElect Serie:
* Vollelektrische Direct-Drive Servo-Technologie
* Sehr geringer Energieverbrauch
* Hohe Präzision und Prozesswiederholgenauigkeit
* Geräuscharmer und vibrationsarmer Betrieb
* Hohe dynamische Servo-Performance
* Geringer Wartungsaufwand
* Saubere Produktionsumgebung
* Ideale Lösung für technische und Präzisionsteile
* Geeignet für schnelle Serienproduktionen
Die Sumitomo Demag IntElect Serie zählt aufgrund ihrer langen Lebensdauer, stabilen Produktionsleistung und hohen Energieeffizienz auch heute noch zu den gefragtesten vollelektrischen Spritzgießmaschinen am Markt.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
9
Машины для обработки пластикаТермопластавтоматыМашины для литья пластмасс под давлением
Ref. no.: 18610Manufacturer: DEMAGYear of construction: 2012Clamping unitClamping force: 160 tonOpening stroke: 495 mmDistance between tie bars: 520 x 520 mmMould height min.: 275 mmMould height max.: 585 mmPlaten size (h x v): 760 x 785 mmInjection unitScrew diameter: 35 mmInjection volume: 156 cm³Shot weight: 139 gInjection pressure: 2180 barMeasurements and weightDimensions: 5,4 x 1,5 x 2,1 mMachine weight: 7600 kgFurther information:The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.Key advantages of the IntElect series:* All-electric direct-drive servo technology* Extremely low energy consumption* High precision and process repeatability* Quiet and low-vibration operation* High dynamic servo performance* Low maintenance requirements* Clean production environment* Ideal solution for technical and precision plastic parts* Suitable for high-speed serial productionThe Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Ref. no.: 18610
Manufacturer: DEMAG
Year of construction: 2012
Clamping unit
Clamping force: 160 ton
Opening stroke: 495 mm
Distance between tie bars: 520 x 520 mm
Mould height min.: 275 mm
Mould height max.: 585 mm
Platen size (h x v): 760 x 785 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 156 cm³
Shot weight: 139 g
Injection pressure: 2180 bar
Measurements and weight
Dimensions: 5,4 x 1,5 x 2,1 m
Machine weight: 7600 kg
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: DEMAG
Year of construction: 2012
Clamping unit
Clamping force: 160 ton
Opening stroke: 495 mm
Distance between tie bars: 520 x 520 mm
Mould height min.: 275 mm
Mould height max.: 585 mm
Platen size (h x v): 760 x 785 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 156 cm³
Shot weight: 139 g
Injection pressure: 2180 bar
Measurements and weight
Dimensions: 5,4 x 1,5 x 2,1 m
Machine weight: 7600 kg
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
2
Металлообработка и станкиСтанки для обработки листового металлаВальцевые станки
Bending length: 2550 mmMax. bending capacity - mild steel: 15Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 15 mmMax. plate thickness without prebending at D=3x upper roll diam. - mild steel: 13 mmMax. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 12 mmMax. plate thickness with prebending at D=5x upper roll diam. - mild steel: 12 mmMax. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 10 mmUpper roll diameter: 270 mmLower roll diameter: 270 mmLateral roll diameter: 230 mmMax. opening: 50 mmWorking height: 1155 mmMotor power: 15 kWLength: 4760 mmWidth: 1660 mmHeight: 1155 mmWeight: 8950 kg
Bending length: 2550 mm
Max. bending capacity - mild steel: 15
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 15 mm
Max. plate thickness without prebending at D=3x upper roll diam. - mild steel: 13 mm
Max. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 12 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 12 mm
Max. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 10 mm
Upper roll diameter: 270 mm
Lower roll diameter: 270 mm
Lateral roll diameter: 230 mm
Max. opening: 50 mm
Working height: 1155 mm
Motor power: 15 kW
Length: 4760 mm
Width: 1660 mm
Height: 1155 mm
Weight: 8950 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Max. bending capacity - mild steel: 15
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 15 mm
Max. plate thickness without prebending at D=3x upper roll diam. - mild steel: 13 mm
Max. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 12 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 12 mm
Max. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 10 mm
Upper roll diameter: 270 mm
Lower roll diameter: 270 mm
Lateral roll diameter: 230 mm
Max. opening: 50 mm
Working height: 1155 mm
Motor power: 15 kW
Length: 4760 mm
Width: 1660 mm
Height: 1155 mm
Weight: 8950 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
1
Металлообработка и станкиСтанки для обработки листового металлаВальцевые станки
Bending length: 1270 mmMax. bending capacity - mild steel: 2.5Upper roll diameter: 90 mmBending speed: 6 m/minMotor power: 1.1 kWLength: 1850 mmWidth: 700 mmHeight: 1200 mmWeight: 520 kg
Bending length: 1270 mm
Max. bending capacity - mild steel: 2.5
Upper roll diameter: 90 mm
Bending speed: 6 m/min
Motor power: 1.1 kW
Length: 1850 mm
Width: 700 mm
Height: 1200 mm
Weight: 520 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Max. bending capacity - mild steel: 2.5
Upper roll diameter: 90 mm
Bending speed: 6 m/min
Motor power: 1.1 kW
Length: 1850 mm
Width: 700 mm
Height: 1200 mm
Weight: 520 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
3
Металлообработка и станкиСтанки для обработки листового металлаЛистогибочные прессы
pressing capacity: 100 toBending length: 1500 mmStroke: 300 mmMotor power: 7.5 kWDie: 1Distance between table and toolholder: 680 mmDistance between columns: 1520 mmWorking speed: 5 mm/sRapid speed: 10 mm/sMax. bending capacity (mild steel): 6 mmHole in table: 100 mmHole distance: 190 mmLength: 2630 mmWidth: 1000 mmHeight: 2275 mmWeight: 2500 kg
pressing capacity: 100 to
Bending length: 1500 mm
Stroke: 300 mm
Motor power: 7.5 kW
Die: 1
Distance between table and toolholder: 680 mm
Distance between columns: 1520 mm
Working speed: 5 mm/s
Rapid speed: 10 mm/s
Max. bending capacity (mild steel): 6 mm
Hole in table: 100 mm
Hole distance: 190 mm
Length: 2630 mm
Width: 1000 mm
Height: 2275 mm
Weight: 2500 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Bending length: 1500 mm
Stroke: 300 mm
Motor power: 7.5 kW
Die: 1
Distance between table and toolholder: 680 mm
Distance between columns: 1520 mm
Working speed: 5 mm/s
Rapid speed: 10 mm/s
Max. bending capacity (mild steel): 6 mm
Hole in table: 100 mm
Hole distance: 190 mm
Length: 2630 mm
Width: 1000 mm
Height: 2275 mm
Weight: 2500 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
4
Металлообработка и станкиСтанки для обработки листового металлаЛистогибочные прессы
pressing capacity: 220 toBending length: 4050 mmAxes: Y1 / Y2 / X and R axisStroke: 265 mmInside distance between side frames: 3600 mmGap in side frame: 410 mmDaylight: 530 mmPower concept: hydraulicrapid speed Y-axis: 200 mm/sWorking speed Y-axis: 12Retractionspeed Y-axis: 180Back gauge travel X-axis: 650 mmBack gauge speed X-axis: 500Back gauge travel R-axis: 250 mmTable height: 900 mmTable width: 104 mmLength: 5250 mmWidth: 1770 mmHeight: 2900 mmWeight: 15000 kg
pressing capacity: 220 to
Bending length: 4050 mm
Axes: Y1 / Y2 / X and R axis
Stroke: 265 mm
Inside distance between side frames: 3600 mm
Gap in side frame: 410 mm
Daylight: 530 mm
Power concept: hydraulic
rapid speed Y-axis: 200 mm/s
Working speed Y-axis: 12
Retractionspeed Y-axis: 180
Back gauge travel X-axis: 650 mm
Back gauge speed X-axis: 500
Back gauge travel R-axis: 250 mm
Table height: 900 mm
Table width: 104 mm
Length: 5250 mm
Width: 1770 mm
Height: 2900 mm
Weight: 15000 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Bending length: 4050 mm
Axes: Y1 / Y2 / X and R axis
Stroke: 265 mm
Inside distance between side frames: 3600 mm
Gap in side frame: 410 mm
Daylight: 530 mm
Power concept: hydraulic
rapid speed Y-axis: 200 mm/s
Working speed Y-axis: 12
Retractionspeed Y-axis: 180
Back gauge travel X-axis: 650 mm
Back gauge speed X-axis: 500
Back gauge travel R-axis: 250 mm
Table height: 900 mm
Table width: 104 mm
Length: 5250 mm
Width: 1770 mm
Height: 2900 mm
Weight: 15000 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
_thumb.png "Показывать рекламу")
_thumb.png "Показывать рекламу")
13
Конвейерная техникаПомпы
Ref. no.: 18637Manufacturer: BUSCHYear of construction: 2010Further information: Make | Model | Year | Capacity | Frequency |Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |Busch Mink MM 1252 AV | 2009 | 250 m³/h | 50 Hz |Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |Busch Mink MM 1252 AV | 2010 | 250/300 m³/h | 50/60 Hz |Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |Busch Mink MM 1252 AV | 2009 | 250/300 m³/h | 50/60 Hz |Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |Busch Mink MM 1252 AV | 2009 | 250/300 m³/h | 50/60 Hz |Busch Mink MM 1252 AV | 2009 | 250/300 m³/h | 50/60 Hz |Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |Busch Mink MM 1252 AV | 2009 | 250/300 m³/h | 50/60 Hz |Busch Mink MM 1252 AV | 2009 | 250/300 m³/h | 50/60 Hz |Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |BUSCH MINK MM 1252 AV VACUUM PUMPSA total of 15 units Busch Mink MM 1252 AV industrial vacuum pumps are available for sale.The pumps were removed from a running production line and are generally in clean and good cosmetic condition. These high-quality Busch MINK series pumps are widely used in plastics injection molding, central vacuum systems, packaging and automation applications.TECHNICAL SPECIFICATIONS• Manufacturer: Busch• Model: MINK MM 1252 AV• Technology: Dry Claw / Oil-Free Vacuum Technology• Capacity: 250 – 300 m³/h• Final Vacuum: 100 hPa (0.1 bar)• Frequency: 50/60 Hz• Year of Manufacture: 2009 / 2010• Origin: GermanyMAIN ADVANTAGES• Oil-free operating system• Low maintenance costs• Energy-efficient operation• Quiet and reliable performance• Suitable for continuous industrial operation• High Busch quality with worldwide service supportAPPLICATION AREAS• Plastic injection molding machines• Central vacuum systems• Packaging machines• Thermoforming systems• Automation and conveying systems• Industrial production facilities
Ref. no.: 18637
Manufacturer: BUSCH
Year of construction: 2010
Further information:
Make | Model | Year | Capacity | Frequency |
Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |
Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |
Busch Mink MM 1252 AV | 2009 | 250 m³/h | 50 Hz |
Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |
Busch Mink MM 1252 AV | 2010 | 250/300 m³/h | 50/60 Hz |
Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |
Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |
Busch Mink MM 1252 AV | 2009 | 250/300 m³/h | 50/60 Hz |
Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |
Busch Mink MM 1252 AV | 2009 | 250/300 m³/h | 50/60 Hz |
Busch Mink MM 1252 AV | 2009 | 250/300 m³/h | 50/60 Hz |
Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |
Busch Mink MM 1252 AV | 2009 | 250/300 m³/h | 50/60 Hz |
Busch Mink MM 1252 AV | 2009 | 250/300 m³/h | 50/60 Hz |
Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |
BUSCH MINK MM 1252 AV VACUUM PUMPS
A total of 15 units Busch Mink MM 1252 AV industrial vacuum pumps are available for sale.
The pumps were removed from a running production line and are generally in clean and good cosmetic condition. These high-quality Busch MINK series pumps are widely used in plastics injection molding, central vacuum systems, packaging and automation applications.
TECHNICAL SPECIFICATIONS
• Manufacturer: Busch
• Model: MINK MM 1252 AV
• Technology: Dry Claw / Oil-Free Vacuum Technology
• Capacity: 250 – 300 m³/h
• Final Vacuum: 100 hPa (0.1 bar)
• Frequency: 50/60 Hz
• Year of Manufacture: 2009 / 2010
• Origin: Germany
MAIN ADVANTAGES
• Oil-free operating system
• Low maintenance costs
• Energy-efficient operation
• Quiet and reliable performance
• Suitable for continuous industrial operation
• High Busch quality with worldwide service support
APPLICATION AREAS
• Plastic injection molding machines
• Central vacuum systems
• Packaging machines
• Thermoforming systems
• Automation and conveying systems
• Industrial production facilities
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: BUSCH
Year of construction: 2010
Further information:
Make | Model | Year | Capacity | Frequency |
Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |
Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |
Busch Mink MM 1252 AV | 2009 | 250 m³/h | 50 Hz |
Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |
Busch Mink MM 1252 AV | 2010 | 250/300 m³/h | 50/60 Hz |
Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |
Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |
Busch Mink MM 1252 AV | 2009 | 250/300 m³/h | 50/60 Hz |
Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |
Busch Mink MM 1252 AV | 2009 | 250/300 m³/h | 50/60 Hz |
Busch Mink MM 1252 AV | 2009 | 250/300 m³/h | 50/60 Hz |
Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |
Busch Mink MM 1252 AV | 2009 | 250/300 m³/h | 50/60 Hz |
Busch Mink MM 1252 AV | 2009 | 250/300 m³/h | 50/60 Hz |
Busch Mink MM 1252 AV | 2010 | 250 m³/h | 50 Hz |
BUSCH MINK MM 1252 AV VACUUM PUMPS
A total of 15 units Busch Mink MM 1252 AV industrial vacuum pumps are available for sale.
The pumps were removed from a running production line and are generally in clean and good cosmetic condition. These high-quality Busch MINK series pumps are widely used in plastics injection molding, central vacuum systems, packaging and automation applications.
TECHNICAL SPECIFICATIONS
• Manufacturer: Busch
• Model: MINK MM 1252 AV
• Technology: Dry Claw / Oil-Free Vacuum Technology
• Capacity: 250 – 300 m³/h
• Final Vacuum: 100 hPa (0.1 bar)
• Frequency: 50/60 Hz
• Year of Manufacture: 2009 / 2010
• Origin: Germany
MAIN ADVANTAGES
• Oil-free operating system
• Low maintenance costs
• Energy-efficient operation
• Quiet and reliable performance
• Suitable for continuous industrial operation
• High Busch quality with worldwide service support
APPLICATION AREAS
• Plastic injection molding machines
• Central vacuum systems
• Packaging machines
• Thermoforming systems
• Automation and conveying systems
• Industrial production facilities
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
12
Конвейерная техникаПомпы
Ref. no.: 18636Manufacturer: EICHHOLZYear of construction: 2014Further information:WHAT IS AN OCTABIN TIPPER?An octabin tipper is an industrial automation system used for the controlled and safe discharge of plastic raw materials, granules, or regrind materials from large-volume octabin containers.Heavy octabins are loaded by forklift and then lifted and tilted in a controlled manner using a hydraulic or chain-driven mechanism. The material is discharged into the lower hopper and can then be transferred to the production line via vacuum conveying or dosing systems.These systems are widely used in plastic injection molding and extrusion plants to reduce labor, increase production efficiency, and ensure safe material handling.FOR SALE: OCTABIN TIPPER + MATERIAL FEEDING SYSTEMFor sale: 1 heavy-duty industrial octabin tipper / material discharge system.The system was removed from a running plastic production line and is in clean and good cosmetic condition.The machine is designed for the controlled discharge of plastic raw materials from large-volume octabins and for transferring the material into centralized conveying systems.The system is equipped with high-quality industrial components from Aerzen, Rittal, Omron, and DMN Westinghouse.BRANDED COMPONENTS INCLUDED IN THE SYSTEMAerzen Vacuum / Blower Unit (Germany)Aerzen is one of the world’s leading German manufacturers of industrial blower and vacuum technologies.Technical Details• Brand: Aerzen• Model: GM15L• Year: 2014• Capacity: 12.50 m³/min• Motor Power: 11 kW• Max. Pressure: 1.25 bar• Operating Pressure: 1.0 bar• Weight: approx. 626 kgAdvantages• High-efficiency German technology• Suitable for continuous industrial operation• Reliable and low-maintenance• Ideal for centralized vacuum systemsRittal Industrial Control SystemThe system is equipped with a Rittal industrial control cabinet.Rittal is a globally recognized premium brand in industrial automation and control systems.Features• Industrial control cabinet• Operator control system• Integrated safety circuits• CE-compliant constructionOmron Safety SensorsThe machine is equipped with Omron safety sensors.Features• Industrial safety barriers• Operator protection system• Safe working area monitoring• Compatible with automation systemsDMN Westinghouse Rotary Valve SystemA DMN Westinghouse rotary valve is installed at the lower hopper outlet.DMN Westinghouse is a globally recognized premium manufacturer for bulk material handling systems.Technical Details• Brand: DMN Westinghouse• Model: ALD 200-6• Low-dust controlled material transfer• Suitable for granule and bulk material applicationsAdvantages• Controlled material flow• Reliable continuous operation• Suitable for centralized conveying systemsOCTABIN TIPPER FEATURES• Heavy-duty steel construction• Chain-driven lifting system• Safety cage• Automatic tipping mechanism• Suitable for large-volume octabins• Designed for continuous industrial operation• Integration into centralized conveying systems• Suitable for plastic granule and regrind applicationsAPPLICATION AREAS• Plastic injection molding plants• Extrusion lines• Centralized material conveying systems• Plastic recycling facilities• Automation and conveying systems• Granule / regrind transfer applications
Ref. no.: 18636
Manufacturer: EICHHOLZ
Year of construction: 2014
Further information:
WHAT IS AN OCTABIN TIPPER?
An octabin tipper is an industrial automation system used for the controlled and safe discharge of plastic raw materials, granules, or regrind materials from large-volume octabin containers.
Heavy octabins are loaded by forklift and then lifted and tilted in a controlled manner using a hydraulic or chain-driven mechanism. The material is discharged into the lower hopper and can then be transferred to the production line via vacuum conveying or dosing systems.
These systems are widely used in plastic injection molding and extrusion plants to reduce labor, increase production efficiency, and ensure safe material handling.
FOR SALE: OCTABIN TIPPER + MATERIAL FEEDING SYSTEM
For sale: 1 heavy-duty industrial octabin tipper / material discharge system.
The system was removed from a running plastic production line and is in clean and good cosmetic condition.
The machine is designed for the controlled discharge of plastic raw materials from large-volume octabins and for transferring the material into centralized conveying systems.
The system is equipped with high-quality industrial components from Aerzen, Rittal, Omron, and DMN Westinghouse.
BRANDED COMPONENTS INCLUDED IN THE SYSTEM
Aerzen Vacuum / Blower Unit (Germany)
Aerzen is one of the world’s leading German manufacturers of industrial blower and vacuum technologies.
Technical Details
• Brand: Aerzen
• Model: GM15L
• Year: 2014
• Capacity: 12.50 m³/min
• Motor Power: 11 kW
• Max. Pressure: 1.25 bar
• Operating Pressure: 1.0 bar
• Weight: approx. 626 kg
Advantages
• High-efficiency German technology
• Suitable for continuous industrial operation
• Reliable and low-maintenance
• Ideal for centralized vacuum systems
Rittal Industrial Control System
The system is equipped with a Rittal industrial control cabinet.
Rittal is a globally recognized premium brand in industrial automation and control systems.
Features
• Industrial control cabinet
• Operator control system
• Integrated safety circuits
• CE-compliant construction
Omron Safety Sensors
The machine is equipped with Omron safety sensors.
Features
• Industrial safety barriers
• Operator protection system
• Safe working area monitoring
• Compatible with automation systems
DMN Westinghouse Rotary Valve System
A DMN Westinghouse rotary valve is installed at the lower hopper outlet.
DMN Westinghouse is a globally recognized premium manufacturer for bulk material handling systems.
Technical Details
• Brand: DMN Westinghouse
• Model: ALD 200-6
• Low-dust controlled material transfer
• Suitable for granule and bulk material applications
Advantages
• Controlled material flow
• Reliable continuous operation
• Suitable for centralized conveying systems
OCTABIN TIPPER FEATURES
• Heavy-duty steel construction
• Chain-driven lifting system
• Safety cage
• Automatic tipping mechanism
• Suitable for large-volume octabins
• Designed for continuous industrial operation
• Integration into centralized conveying systems
• Suitable for plastic granule and regrind applications
APPLICATION AREAS
• Plastic injection molding plants
• Extrusion lines
• Centralized material conveying systems
• Plastic recycling facilities
• Automation and conveying systems
• Granule / regrind transfer applications
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Manufacturer: EICHHOLZ
Year of construction: 2014
Further information:
WHAT IS AN OCTABIN TIPPER?
An octabin tipper is an industrial automation system used for the controlled and safe discharge of plastic raw materials, granules, or regrind materials from large-volume octabin containers.
Heavy octabins are loaded by forklift and then lifted and tilted in a controlled manner using a hydraulic or chain-driven mechanism. The material is discharged into the lower hopper and can then be transferred to the production line via vacuum conveying or dosing systems.
These systems are widely used in plastic injection molding and extrusion plants to reduce labor, increase production efficiency, and ensure safe material handling.
FOR SALE: OCTABIN TIPPER + MATERIAL FEEDING SYSTEM
For sale: 1 heavy-duty industrial octabin tipper / material discharge system.
The system was removed from a running plastic production line and is in clean and good cosmetic condition.
The machine is designed for the controlled discharge of plastic raw materials from large-volume octabins and for transferring the material into centralized conveying systems.
The system is equipped with high-quality industrial components from Aerzen, Rittal, Omron, and DMN Westinghouse.
BRANDED COMPONENTS INCLUDED IN THE SYSTEM
Aerzen Vacuum / Blower Unit (Germany)
Aerzen is one of the world’s leading German manufacturers of industrial blower and vacuum technologies.
Technical Details
• Brand: Aerzen
• Model: GM15L
• Year: 2014
• Capacity: 12.50 m³/min
• Motor Power: 11 kW
• Max. Pressure: 1.25 bar
• Operating Pressure: 1.0 bar
• Weight: approx. 626 kg
Advantages
• High-efficiency German technology
• Suitable for continuous industrial operation
• Reliable and low-maintenance
• Ideal for centralized vacuum systems
Rittal Industrial Control System
The system is equipped with a Rittal industrial control cabinet.
Rittal is a globally recognized premium brand in industrial automation and control systems.
Features
• Industrial control cabinet
• Operator control system
• Integrated safety circuits
• CE-compliant construction
Omron Safety Sensors
The machine is equipped with Omron safety sensors.
Features
• Industrial safety barriers
• Operator protection system
• Safe working area monitoring
• Compatible with automation systems
DMN Westinghouse Rotary Valve System
A DMN Westinghouse rotary valve is installed at the lower hopper outlet.
DMN Westinghouse is a globally recognized premium manufacturer for bulk material handling systems.
Technical Details
• Brand: DMN Westinghouse
• Model: ALD 200-6
• Low-dust controlled material transfer
• Suitable for granule and bulk material applications
Advantages
• Controlled material flow
• Reliable continuous operation
• Suitable for centralized conveying systems
OCTABIN TIPPER FEATURES
• Heavy-duty steel construction
• Chain-driven lifting system
• Safety cage
• Automatic tipping mechanism
• Suitable for large-volume octabins
• Designed for continuous industrial operation
• Integration into centralized conveying systems
• Suitable for plastic granule and regrind applications
APPLICATION AREAS
• Plastic injection molding plants
• Extrusion lines
• Centralized material conveying systems
• Plastic recycling facilities
• Automation and conveying systems
• Granule / regrind transfer applications
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
6
Металлообработка и станкиТокарные станкиТокарные станки для тяжелых условий эксплуатации
Drehdurchmesser über Bett: 1930 mmDrehdurchmesser über Support: 1520 mmDrehlänge: 5000 mmDrehzahl: 0,5-250 U/minSpindelbohrung: 105 mmWerkstückgewicht: 35 tLünette: 1000-1600 mmSteuerung: SiemensGesamtleistungsbedarf: 106 kWMaschinengewicht ca.: tRaumbedarf ca.: m
Drehdurchmesser über Bett: 1930 mm
Drehdurchmesser über Support: 1520 mm
Drehlänge: 5000 mm
Drehzahl: 0,5-250 U/min
Spindelbohrung: 105 mm
Werkstückgewicht: 35 t
Lünette: 1000-1600 mm
Steuerung: Siemens
Gesamtleistungsbedarf: 106 kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Drehdurchmesser über Support: 1520 mm
Drehlänge: 5000 mm
Drehzahl: 0,5-250 U/min
Spindelbohrung: 105 mm
Werkstückgewicht: 35 t
Lünette: 1000-1600 mm
Steuerung: Siemens
Gesamtleistungsbedarf: 106 kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
10
Металлообработка и станкиТокарные станкиЦентровочно-токарные и шпиндельные станки
Drehdurchmesser über Bett: 540 mmDrehdurchmesser über Support: 340 mmDrehdurchmesser in der Kröpfung: 800 mmLänge der Kröpfung: 350 mmDrehlänge: 3000 mmDrehzahl: 40-1800 U/minBettbreite: 340 mmDreibackenfutter: 255 mmSpindeldurchlass: 52 mmGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Drehdurchmesser über Bett: 540 mm
Drehdurchmesser über Support: 340 mm
Drehdurchmesser in der Kröpfung: 800 mm
Länge der Kröpfung: 350 mm
Drehlänge: 3000 mm
Drehzahl: 40-1800 U/min
Bettbreite: 340 mm
Dreibackenfutter: 255 mm
Spindeldurchlass: 52 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Drehdurchmesser über Support: 340 mm
Drehdurchmesser in der Kröpfung: 800 mm
Länge der Kröpfung: 350 mm
Drehlänge: 3000 mm
Drehzahl: 40-1800 U/min
Bettbreite: 340 mm
Dreibackenfutter: 255 mm
Spindeldurchlass: 52 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
10
Металлообработка и станкиТокарные станкиТокарные станки
Drehdurchmesser: 820 mmDrehlänge: 6000 mmDrehdurchmesser über Support: 520 mmSteuerung: SiemensTyp: 805Reitstock-Pinolenaufnahme MK: 6Getriebestufen: 2Drehzahl: 8-1600 U/minBettbreite: 560 mmSpindelbohrung: 128 mmPlanscheibe: 600 mmDreibackenfutter Forckrath: 400 mmLünette: 250-500 mmPinolendurchmesser: 125 mmPinolenhub: 280 mmGesamtleistungsbedarf: KVAMaschinengewicht ca.: 12 tRaumbedarf ca.: 9,5x2,5x2,5 m
Drehdurchmesser: 820 mm
Drehlänge: 6000 mm
Drehdurchmesser über Support: 520 mm
Steuerung: Siemens
Typ: 805
Reitstock-Pinolenaufnahme MK: 6
Getriebestufen: 2
Drehzahl: 8-1600 U/min
Bettbreite: 560 mm
Spindelbohrung: 128 mm
Planscheibe: 600 mm
Dreibackenfutter Forckrath: 400 mm
Lünette: 250-500 mm
Pinolendurchmesser: 125 mm
Pinolenhub: 280 mm
Gesamtleistungsbedarf: KVA
Maschinengewicht ca.: 12 t
Raumbedarf ca.: 9,5x2,5x2,5 m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Drehlänge: 6000 mm
Drehdurchmesser über Support: 520 mm
Steuerung: Siemens
Typ: 805
Reitstock-Pinolenaufnahme MK: 6
Getriebestufen: 2
Drehzahl: 8-1600 U/min
Bettbreite: 560 mm
Spindelbohrung: 128 mm
Planscheibe: 600 mm
Dreibackenfutter Forckrath: 400 mm
Lünette: 250-500 mm
Pinolendurchmesser: 125 mm
Pinolenhub: 280 mm
Gesamtleistungsbedarf: KVA
Maschinengewicht ca.: 12 t
Raumbedarf ca.: 9,5x2,5x2,5 m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
10
Металлообработка и станкиТокарные станкиТокарные станки
Drehdurchmesser: 1010 mmDrehlänge: 6000 mmSteuerung: SiemensTyp: Sinumerik 840DDrehdurchmesser über Support: 650 mmDreibackenfutter: Schunk Rota PlusDreibackenfutter Durchmesser: 500 mmBettbreite: 750 mmLünette: 450 mmDrehgeschwindigkeit: 1100 U/minLänge der Kröpfung: 500 mmSpindeldurchlass: 104 mmWerkstückgewicht: 7000 kgHauptmotor: 52 kWDrehzahl: 5-900 U/minGesamtleistungsbedarf: . kWMaschinengewicht ca.: . tRaumbedarf ca.: . m
Drehdurchmesser: 1010 mm
Drehlänge: 6000 mm
Steuerung: Siemens
Typ: Sinumerik 840D
Drehdurchmesser über Support: 650 mm
Dreibackenfutter: Schunk Rota Plus
Dreibackenfutter Durchmesser: 500 mm
Bettbreite: 750 mm
Lünette: 450 mm
Drehgeschwindigkeit: 1100 U/min
Länge der Kröpfung: 500 mm
Spindeldurchlass: 104 mm
Werkstückgewicht: 7000 kg
Hauptmotor: 52 kW
Drehzahl: 5-900 U/min
Gesamtleistungsbedarf: . kW
Maschinengewicht ca.: . t
Raumbedarf ca.: . m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Drehlänge: 6000 mm
Steuerung: Siemens
Typ: Sinumerik 840D
Drehdurchmesser über Support: 650 mm
Dreibackenfutter: Schunk Rota Plus
Dreibackenfutter Durchmesser: 500 mm
Bettbreite: 750 mm
Lünette: 450 mm
Drehgeschwindigkeit: 1100 U/min
Länge der Kröpfung: 500 mm
Spindeldurchlass: 104 mm
Werkstückgewicht: 7000 kg
Hauptmotor: 52 kW
Drehzahl: 5-900 U/min
Gesamtleistungsbedarf: . kW
Maschinengewicht ca.: . t
Raumbedarf ca.: . m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
10
Металлообработка и станкиТокарные станкиТокарные станки
Drehdurchmesser: 1010 mmDrehlänge: 6000 mmSteuerung: SiemensTyp: Sinumerik 840DDrehdurchmesser über Support: 650 mmDreibackenfutter: Schunk Rota PlusDreibackenfutter Durchmesser: 500 mmBettbreite: 750 mmLünette: 450 mmDrehgeschwindigkeit: 1100 U/minLänge der Kröpfung: 500 mmSpindeldurchlass: 104 mmWerkstückgewicht: 7000 kgHauptmotor: 52 kWDrehzahl: 5-900 U/minGesamtleistungsbedarf: . kWMaschinengewicht ca.: . tRaumbedarf ca.: . m
Drehdurchmesser: 1010 mm
Drehlänge: 6000 mm
Steuerung: Siemens
Typ: Sinumerik 840D
Drehdurchmesser über Support: 650 mm
Dreibackenfutter: Schunk Rota Plus
Dreibackenfutter Durchmesser: 500 mm
Bettbreite: 750 mm
Lünette: 450 mm
Drehgeschwindigkeit: 1100 U/min
Länge der Kröpfung: 500 mm
Spindeldurchlass: 104 mm
Werkstückgewicht: 7000 kg
Hauptmotor: 52 kW
Drehzahl: 5-900 U/min
Gesamtleistungsbedarf: . kW
Maschinengewicht ca.: . t
Raumbedarf ca.: . m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Drehlänge: 6000 mm
Steuerung: Siemens
Typ: Sinumerik 840D
Drehdurchmesser über Support: 650 mm
Dreibackenfutter: Schunk Rota Plus
Dreibackenfutter Durchmesser: 500 mm
Bettbreite: 750 mm
Lünette: 450 mm
Drehgeschwindigkeit: 1100 U/min
Länge der Kröpfung: 500 mm
Spindeldurchlass: 104 mm
Werkstückgewicht: 7000 kg
Hauptmotor: 52 kW
Drehzahl: 5-900 U/min
Gesamtleistungsbedarf: . kW
Maschinengewicht ca.: . t
Raumbedarf ca.: . m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
5
Металлообработка и станкиТокарные станкиТокарные станки
Drehdurchmesser: . mmDrehlänge: . mmSteuerung: .Typ: . CCUODrehdurchmesser über Support: . mmPlanweg: . mmSpindeldurchlass: . mmDrehzahl: . U/minGetriebestufen: .Pinolenhub: . mmEilgang: . m/minHauptantriebsmotor: . kWDreibackenfutter Durchmesser: . mmGesamtleistungsbedarf: . kWMaschinengewicht ca.: . tRaumbedarf ca.: . m
Drehdurchmesser: . mm
Drehlänge: . mm
Steuerung: .
Typ: . CCUO
Drehdurchmesser über Support: . mm
Planweg: . mm
Spindeldurchlass: . mm
Drehzahl: . U/min
Getriebestufen: .
Pinolenhub: . mm
Eilgang: . m/min
Hauptantriebsmotor: . kW
Dreibackenfutter Durchmesser: . mm
Gesamtleistungsbedarf: . kW
Maschinengewicht ca.: . t
Raumbedarf ca.: . m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Drehlänge: . mm
Steuerung: .
Typ: . CCUO
Drehdurchmesser über Support: . mm
Planweg: . mm
Spindeldurchlass: . mm
Drehzahl: . U/min
Getriebestufen: .
Pinolenhub: . mm
Eilgang: . m/min
Hauptantriebsmotor: . kW
Dreibackenfutter Durchmesser: . mm
Gesamtleistungsbedarf: . kW
Maschinengewicht ca.: . t
Raumbedarf ca.: . m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
6
Металлообработка и станкиТокарные станкиТокарно-фрезерные центры с ЧПУ
Drehdurchmesser: 890,820 mmDrehlänge: 4000 mmSteuerung: Siemens SIN 880TSpindelaufnahme: DIN 55026/15Spindeldurchlass: 122 mmPlanweg: 500 mmPinolenhub: 140 mmReitstockverschiebung: 3708 mmSpindeldrehzahlen: 5-1800 U/minFräseraufnahme: 1500-6000 U/minVorschub: 0,5-5000 mm/minEilgang: 15 m/minVorschubkraft: 22000/10000 NWerkzeugwechsler: 95 St.Lünette: CNCReitstock: CNCGesamtleistungsbedarf: 50/69 kWMaschinengewicht ca.: 23,5 tRaumbedarf ca.: 10x4x3,3 m
Drehdurchmesser: 890,820 mm
Drehlänge: 4000 mm
Steuerung: Siemens SIN 880T
Spindelaufnahme: DIN 55026/15
Spindeldurchlass: 122 mm
Planweg: 500 mm
Pinolenhub: 140 mm
Reitstockverschiebung: 3708 mm
Spindeldrehzahlen: 5-1800 U/min
Fräseraufnahme: 1500-6000 U/min
Vorschub: 0,5-5000 mm/min
Eilgang: 15 m/min
Vorschubkraft: 22000/10000 N
Werkzeugwechsler: 95 St.
Lünette: CNC
Reitstock: CNC
Gesamtleistungsbedarf: 50/69 kW
Maschinengewicht ca.: 23,5 t
Raumbedarf ca.: 10x4x3,3 m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Drehlänge: 4000 mm
Steuerung: Siemens SIN 880T
Spindelaufnahme: DIN 55026/15
Spindeldurchlass: 122 mm
Planweg: 500 mm
Pinolenhub: 140 mm
Reitstockverschiebung: 3708 mm
Spindeldrehzahlen: 5-1800 U/min
Fräseraufnahme: 1500-6000 U/min
Vorschub: 0,5-5000 mm/min
Eilgang: 15 m/min
Vorschubkraft: 22000/10000 N
Werkzeugwechsler: 95 St.
Lünette: CNC
Reitstock: CNC
Gesamtleistungsbedarf: 50/69 kW
Maschinengewicht ca.: 23,5 t
Raumbedarf ca.: 10x4x3,3 m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
4
Металлообработка и станкиАксессуары и запчастиПоворотные столы
Tischabmessung: 1500x1200 mmTischhöhe: 520 mmT-Nuten - Breite: 28/48 mmT-Nuten - Abstand: 155 mmSteuerung: NCGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Tischabmessung: 1500x1200 mm
Tischhöhe: 520 mm
T-Nuten - Breite: 28/48 mm
T-Nuten - Abstand: 155 mm
Steuerung: NC
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Tischhöhe: 520 mm
T-Nuten - Breite: 28/48 mm
T-Nuten - Abstand: 155 mm
Steuerung: NC
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
7
Металлообработка и станкиАксессуары и запчастиПоля тарелок
Länge: 5200 mmBreite: 2000 mmDicke: 400 mmAnzahl der T-Nuten: 6T-Nuten - Breite: 32 mmGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Länge: 5200 mm
Breite: 2000 mm
Dicke: 400 mm
Anzahl der T-Nuten: 6
T-Nuten - Breite: 32 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Breite: 2000 mm
Dicke: 400 mm
Anzahl der T-Nuten: 6
T-Nuten - Breite: 32 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
1
Металлообработка и станкиАксессуары и запчастиПоля тарелок
Länge: 4800 mmBreite: 3740 mmAnzahl: 1Dicke: 300 mmGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Länge: 4800 mm
Breite: 3740 mm
Anzahl: 1
Dicke: 300 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Breite: 3740 mm
Anzahl: 1
Dicke: 300 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
3
Металлообработка и станкиАксессуары и запчастиТокарные планшайбы
Planscheibendurchmesser: 610 mmGesamtleistungsbedarf: . kWMaschinengewicht ca.: . kgRaumbedarf ca.: . m
Planscheibendurchmesser: 610 mm
Gesamtleistungsbedarf: . kW
Maschinengewicht ca.: . kg
Raumbedarf ca.: . m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Gesamtleistungsbedarf: . kW
Maschinengewicht ca.: . kg
Raumbedarf ca.: . m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
4
ЭлектроэнергетикаДвигатели
Antriebsleistung: . kWVolt: . VAmpere: . AGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Antriebsleistung: . kW
Volt: . V
Ampere: . A
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Volt: . V
Ampere: . A
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
6
Металлообработка и станкиАксессуары и запчастиПрочее
Umlaufdurchmesser: 520 mmSpitzenhöhe: 500 mmBreite: 20 mmPinole:: 3 St.Pinolendurchmesser: 70 mmLagerdurchmesser: 65 mmGrundplatte: 415x270 mmGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Umlaufdurchmesser: 520 mm
Spitzenhöhe: 500 mm
Breite: 20 mm
Pinole:: 3 St.
Pinolendurchmesser: 70 mm
Lagerdurchmesser: 65 mm
Grundplatte: 415x270 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Spitzenhöhe: 500 mm
Breite: 20 mm
Pinole:: 3 St.
Pinolendurchmesser: 70 mm
Lagerdurchmesser: 65 mm
Grundplatte: 415x270 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
10
Металлообработка и станкиАксессуары и запчасти
Förderdruck: . barLiterleistung: . lAntriebsleistung: . kWGesamtleistungsbedarf: . kWMaschinengewicht ca.: . tRaumbedarf ca.: . m
Förderdruck: . bar
Literleistung: . l
Antriebsleistung: . kW
Gesamtleistungsbedarf: . kW
Maschinengewicht ca.: . t
Raumbedarf ca.: . m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Literleistung: . l
Antriebsleistung: . kW
Gesamtleistungsbedarf: . kW
Maschinengewicht ca.: . t
Raumbedarf ca.: . m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
2
Металлообработка и станкиАксессуары и запчасти
Lagernummer: 1077-Z01252Maschinenart: ErsatzteileFabrikat: VAHLETyp: Powercom A-MasterBaujahr: unbekanntSteuerung: konventionellLagerort: DorstenUrsprungsland: -Lieferzeit: sofortFrachtbasis: ab StandortPreis: Auf Anfrage
Lagernummer: 1077-Z01252
Maschinenart: Ersatzteile
Fabrikat: VAHLE
Typ: Powercom A-Master
Baujahr: unbekannt
Steuerung: konventionell
Lagerort: Dorsten
Ursprungsland: -
Lieferzeit: sofort
Frachtbasis: ab Standort
Preis: Auf Anfrage
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Maschinenart: Ersatzteile
Fabrikat: VAHLE
Typ: Powercom A-Master
Baujahr: unbekannt
Steuerung: konventionell
Lagerort: Dorsten
Ursprungsland: -
Lieferzeit: sofort
Frachtbasis: ab Standort
Preis: Auf Anfrage
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
3
Металлообработка и станкиАксессуары и запчастиУглы зажима
Breite: 520 mmHöhe: 700 mmTiefe: 350 mmStärke der Aufspannplatte: mmGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Breite: 520 mm
Höhe: 700 mm
Tiefe: 350 mm
Stärke der Aufspannplatte: mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Höhe: 700 mm
Tiefe: 350 mm
Stärke der Aufspannplatte: mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
4
Металлообработка и станкиАксессуары и запчастиЗажимные столы
Tischlänge: 630 mmTischbreite: 630 mmTischbelastung: . tGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Tischlänge: 630 mm
Tischbreite: 630 mm
Tischbelastung: . t
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Tischbreite: 630 mm
Tischbelastung: . t
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
4
Металлообработка и станкиАксессуары и запчастиПодштамповые плиты
Plattenlänge: 9000 mmPlattenbreite: 3000 mmPlattenhöhe: 400 mmT-Nuten - Breite: 32/56 mmT - Nutenabstand: 335 mmAnzahl der T-Nuten: 9Gesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Plattenlänge: 9000 mm
Plattenbreite: 3000 mm
Plattenhöhe: 400 mm
T-Nuten - Breite: 32/56 mm
T - Nutenabstand: 335 mm
Anzahl der T-Nuten: 9
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Plattenbreite: 3000 mm
Plattenhöhe: 400 mm
T-Nuten - Breite: 32/56 mm
T - Nutenabstand: 335 mm
Anzahl der T-Nuten: 9
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
13
Машины для обработки пластикаТермопластавтоматыМашины для литья пластмасс под давлением
Ref. no.: 18657Hersteller: ENGELYear of construction: 2016Clamping unitClamping force: 160 tonOpening stroke: 900 mmMould height min.: 300 mmMould height max.: 600 mmPlaten size (h x v): 750 X 750 mmInjection unitScrew diameter: 35 mmInjection volume: 168 cm³Shot weight: 151 gInjection pressure: 2400 barMeasurements and weightDimensions: 5,7 X 1,8 X 2,2 mMachine weight: 10200 kgFurther information:Tie-bar-less + electric injection = maximum flexibility and precisionENGEL e-victory 440/160:👉 This is a hybrid machine (servo-hydraulic + electric)⸻🔍 How it works✔ Electric part:* Injection unit (screw movement)* Ensures very high precision and process stability✔ Hydraulic part:* Clamping unit (mould closing)* Maintains clamping force efficiently without continuous energy consumption👉 This system combines:* The precision of an all-electric machine* With the power and efficiency of a hydraulic systemThis is a modern servo-hydraulic injection moulding machine from the well-established ENGEL e-victory series, known for its energy efficiency, high precision, and tie-bar-less design.The machine has a clamping force of 160 tons and is ideally suited for technical plastic parts as well as demanding applications in industries such as automotive, medical, and general manufacturing.Key features:* Tie-bar-less design for maximum mould flexibility* Servo-hydraulic drive for high energy efficiency* Precise and stable processing performance* Compact footprint with a large mould installation area* Modern ENGEL control systemThe machine was manufactured in 2016 and appears to be in very good condition, both technically and visually, as can be seen in the pictures.Thanks to its tie-bar-less design, this machine offers clear advantages when working with large or complex moulds and ensures highly flexible production.
Ref. no.: 18657
Hersteller: ENGEL
Year of construction: 2016
Clamping unit
Clamping force: 160 ton
Opening stroke: 900 mm
Mould height min.: 300 mm
Mould height max.: 600 mm
Platen size (h x v): 750 X 750 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 168 cm³
Shot weight: 151 g
Injection pressure: 2400 bar
Measurements and weight
Dimensions: 5,7 X 1,8 X 2,2 m
Machine weight: 10200 kg
Further information:
Tie-bar-less + electric injection = maximum flexibility and precision
ENGEL e-victory 440/160:
👉 This is a hybrid machine (servo-hydraulic + electric)
⸻
🔍 How it works
✔ Electric part:
* Injection unit (screw movement)
* Ensures very high precision and process stability
✔ Hydraulic part:
* Clamping unit (mould closing)
* Maintains clamping force efficiently without continuous energy consumption
👉 This system combines:
* The precision of an all-electric machine
* With the power and efficiency of a hydraulic system
This is a modern servo-hydraulic injection moulding machine from the well-established ENGEL e-victory series, known for its energy efficiency, high precision, and tie-bar-less design.
The machine has a clamping force of 160 tons and is ideally suited for technical plastic parts as well as demanding applications in industries such as automotive, medical, and general manufacturing.
Key features:
* Tie-bar-less design for maximum mould flexibility
* Servo-hydraulic drive for high energy efficiency
* Precise and stable processing performance
* Compact footprint with a large mould installation area
* Modern ENGEL control system
The machine was manufactured in 2016 and appears to be in very good condition, both technically and visually, as can be seen in the pictures.
Thanks to its tie-bar-less design, this machine offers clear advantages when working with large or complex moulds and ensures highly flexible production.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Hersteller: ENGEL
Year of construction: 2016
Clamping unit
Clamping force: 160 ton
Opening stroke: 900 mm
Mould height min.: 300 mm
Mould height max.: 600 mm
Platen size (h x v): 750 X 750 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 168 cm³
Shot weight: 151 g
Injection pressure: 2400 bar
Measurements and weight
Dimensions: 5,7 X 1,8 X 2,2 m
Machine weight: 10200 kg
Further information:
Tie-bar-less + electric injection = maximum flexibility and precision
ENGEL e-victory 440/160:
👉 This is a hybrid machine (servo-hydraulic + electric)
⸻
🔍 How it works
✔ Electric part:
* Injection unit (screw movement)
* Ensures very high precision and process stability
✔ Hydraulic part:
* Clamping unit (mould closing)
* Maintains clamping force efficiently without continuous energy consumption
👉 This system combines:
* The precision of an all-electric machine
* With the power and efficiency of a hydraulic system
This is a modern servo-hydraulic injection moulding machine from the well-established ENGEL e-victory series, known for its energy efficiency, high precision, and tie-bar-less design.
The machine has a clamping force of 160 tons and is ideally suited for technical plastic parts as well as demanding applications in industries such as automotive, medical, and general manufacturing.
Key features:
* Tie-bar-less design for maximum mould flexibility
* Servo-hydraulic drive for high energy efficiency
* Precise and stable processing performance
* Compact footprint with a large mould installation area
* Modern ENGEL control system
The machine was manufactured in 2016 and appears to be in very good condition, both technically and visually, as can be seen in the pictures.
Thanks to its tie-bar-less design, this machine offers clear advantages when working with large or complex moulds and ensures highly flexible production.
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
3
Металлообработка и станкиСверлильные станки и расточные станки
Drilling capacy mild steel: 25 mmTaper: MK 3Distance spindle - column: 280 mmRevs: 125 - 4000 (2 Stufen) r.p.m.Motor: 0,9 / 1,45 kWTapping capacity: M20max. drilling depth: 125 mmColumn diameter: 110 mmDistance spindle - table: 240 - 790 mmTable: 420 x 340 mmQuill travel: 125 mmLength: 520 mmWidth: 820 mmHeight: 1900 mmWeight: 275 kg
Drilling capacy mild steel: 25 mm
Taper: MK 3
Distance spindle - column: 280 mm
Revs: 125 - 4000 (2 Stufen) r.p.m.
Motor: 0,9 / 1,45 kW
Tapping capacity: M20
max. drilling depth: 125 mm
Column diameter: 110 mm
Distance spindle - table: 240 - 790 mm
Table: 420 x 340 mm
Quill travel: 125 mm
Length: 520 mm
Width: 820 mm
Height: 1900 mm
Weight: 275 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Taper: MK 3
Distance spindle - column: 280 mm
Revs: 125 - 4000 (2 Stufen) r.p.m.
Motor: 0,9 / 1,45 kW
Tapping capacity: M20
max. drilling depth: 125 mm
Column diameter: 110 mm
Distance spindle - table: 240 - 790 mm
Table: 420 x 340 mm
Quill travel: 125 mm
Length: 520 mm
Width: 820 mm
Height: 1900 mm
Weight: 275 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
3
Металлообработка и станкиСверлильные станки и расточные станки
Drilling capacy mild steel: 25 mmTaper: MK 3Distance spindle - column: 280 mmRevs: 125 - 4000 (2 Stufen) r.p.m.Motor: 0,9 / 1,45 kWTapping capacity: M20max. drilling depth: 125 mmColumn diameter: 110 mmDistance spindle - table: 240 - 790 mmTable: 420 x 340 mmLength: 520 mmWidth: 820 mmHeight: 1900 mmWeight: 275 kg
Drilling capacy mild steel: 25 mm
Taper: MK 3
Distance spindle - column: 280 mm
Revs: 125 - 4000 (2 Stufen) r.p.m.
Motor: 0,9 / 1,45 kW
Tapping capacity: M20
max. drilling depth: 125 mm
Column diameter: 110 mm
Distance spindle - table: 240 - 790 mm
Table: 420 x 340 mm
Length: 520 mm
Width: 820 mm
Height: 1900 mm
Weight: 275 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Taper: MK 3
Distance spindle - column: 280 mm
Revs: 125 - 4000 (2 Stufen) r.p.m.
Motor: 0,9 / 1,45 kW
Tapping capacity: M20
max. drilling depth: 125 mm
Column diameter: 110 mm
Distance spindle - table: 240 - 790 mm
Table: 420 x 340 mm
Length: 520 mm
Width: 820 mm
Height: 1900 mm
Weight: 275 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
1
Металлообработка и станкиПилыЛенточные пилы
Saw frame: Pivot frameBand dimensions: 5200x34x1,1 mmBand speed continous: 20-100 m/minCutting capacity 0° round: 440 mmCutting capacity 0° square: 440 mmCutting capacity 0° flat: 610x440 mmCutting capacity 45°: rund 410 mm, quadrat 410 mm, rechteck 410 x 440 mmCutting capacity 60°: rund 320 mm, quadrat 250 mm, rechteck 250 x 440 mmCutting capacity - 45°: rund 410 mm, quadrat 410 mm, rechteck 410 x 440 mmCutting capacity - 60°: rund 320 mm, quadrat 285 mm, rechteck 285 x 440 mmWorking height: 860 mmHydraulic motor: 0.55 kWMotor: 3 kWCoolant pump motor: 0.12 kWLength: 2800 mmWidth: 1210 mmHeight: 1870 mmWeight: 1540 kg
Saw frame: Pivot frame
Band dimensions: 5200x34x1,1 mm
Band speed continous: 20-100 m/min
Cutting capacity 0° round: 440 mm
Cutting capacity 0° square: 440 mm
Cutting capacity 0° flat: 610x440 mm
Cutting capacity 45°: rund 410 mm, quadrat 410 mm, rechteck 410 x 440 mm
Cutting capacity 60°: rund 320 mm, quadrat 250 mm, rechteck 250 x 440 mm
Cutting capacity - 45°: rund 410 mm, quadrat 410 mm, rechteck 410 x 440 mm
Cutting capacity - 60°: rund 320 mm, quadrat 285 mm, rechteck 285 x 440 mm
Working height: 860 mm
Hydraulic motor: 0.55 kW
Motor: 3 kW
Coolant pump motor: 0.12 kW
Length: 2800 mm
Width: 1210 mm
Height: 1870 mm
Weight: 1540 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Band dimensions: 5200x34x1,1 mm
Band speed continous: 20-100 m/min
Cutting capacity 0° round: 440 mm
Cutting capacity 0° square: 440 mm
Cutting capacity 0° flat: 610x440 mm
Cutting capacity 45°: rund 410 mm, quadrat 410 mm, rechteck 410 x 440 mm
Cutting capacity 60°: rund 320 mm, quadrat 250 mm, rechteck 250 x 440 mm
Cutting capacity - 45°: rund 410 mm, quadrat 410 mm, rechteck 410 x 440 mm
Cutting capacity - 60°: rund 320 mm, quadrat 285 mm, rechteck 285 x 440 mm
Working height: 860 mm
Hydraulic motor: 0.55 kW
Motor: 3 kW
Coolant pump motor: 0.12 kW
Length: 2800 mm
Width: 1210 mm
Height: 1870 mm
Weight: 1540 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
5
Металлообработка и станкиСверлильные станки и расточные станки
Drilling capacy mild steel: 15 mmTaper: MK 2Distance spindle - column: 220 mmRevs: 40 - 4000 r.p.m.Tapping capacity: M12Quill travel: 70 mmDistance spindle - table: 85 - 370 mmTable: 300 x 250 mmColumn diameter: 70 mmLength: 400 mmWidth: 520 mmHeight: 850 mmWeight: 65 kg
Drilling capacy mild steel: 15 mm
Taper: MK 2
Distance spindle - column: 220 mm
Revs: 40 - 4000 r.p.m.
Tapping capacity: M12
Quill travel: 70 mm
Distance spindle - table: 85 - 370 mm
Table: 300 x 250 mm
Column diameter: 70 mm
Length: 400 mm
Width: 520 mm
Height: 850 mm
Weight: 65 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Taper: MK 2
Distance spindle - column: 220 mm
Revs: 40 - 4000 r.p.m.
Tapping capacity: M12
Quill travel: 70 mm
Distance spindle - table: 85 - 370 mm
Table: 300 x 250 mm
Column diameter: 70 mm
Length: 400 mm
Width: 520 mm
Height: 850 mm
Weight: 65 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
4
Металлообработка и станкиСверлильные станки и расточные станки
Drilling capacy mild steel: 6 mmTaper: B 12Distance spindle - column: 220 mmRevs: 100 - 10000 r.p.m.Tapping capacity: M5Quill travel: 60 mmDistance spindle - table: 140 - 315 mmTable: 300 x 250 mmColumn diameter: 70 mmLength: 452 mmWidth: 700 mmHeight: 1130 mmWeight: 44 kg
Drilling capacy mild steel: 6 mm
Taper: B 12
Distance spindle - column: 220 mm
Revs: 100 - 10000 r.p.m.
Tapping capacity: M5
Quill travel: 60 mm
Distance spindle - table: 140 - 315 mm
Table: 300 x 250 mm
Column diameter: 70 mm
Length: 452 mm
Width: 700 mm
Height: 1130 mm
Weight: 44 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Taper: B 12
Distance spindle - column: 220 mm
Revs: 100 - 10000 r.p.m.
Tapping capacity: M5
Quill travel: 60 mm
Distance spindle - table: 140 - 315 mm
Table: 300 x 250 mm
Column diameter: 70 mm
Length: 452 mm
Width: 700 mm
Height: 1130 mm
Weight: 44 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
5
Металлообработка и станкиСверлильные станки и расточные станки
Drilling capacy mild steel: 10 mmTaper: B 16Distance spindle - column: 220 mmRevs: 60 - 6000 r.p.m.Quill travel: 60 mmDistance spindle - table: 140 - 315 mmTable: 300 x 250 mmColumn diameter: 70 mmLength: 350 mmWidth: 520 mmHeight: 820 mmWeight: 44 kg
Drilling capacy mild steel: 10 mm
Taper: B 16
Distance spindle - column: 220 mm
Revs: 60 - 6000 r.p.m.
Quill travel: 60 mm
Distance spindle - table: 140 - 315 mm
Table: 300 x 250 mm
Column diameter: 70 mm
Length: 350 mm
Width: 520 mm
Height: 820 mm
Weight: 44 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.
Taper: B 16
Distance spindle - column: 220 mm
Revs: 60 - 6000 r.p.m.
Quill travel: 60 mm
Distance spindle - table: 140 - 315 mm
Table: 300 x 250 mm
Column diameter: 70 mm
Length: 350 mm
Width: 520 mm
Height: 820 mm
Weight: 44 kg
Объявление было переведено автоматически, и, возможно, содержит некоторые ошибки перевода.