KSB ETALINE Z Volite casing pump, 2019, single stage volute casing pump inline design as twin pump, water meters, variable speed, 3Kw motors, 3Ph

Kaeser SK26 Air compressor, serial: 2610494, Air compressor, 15Kw, 7.5Bar, rate motor speed 3000/min, 3Ph

Decalinox holding tank Stainless 400L holding tank, with lid, side bottom discharge

Decalinox holding tank Stainless 200L holding tank, with lid, side bottom discharge

VMI 2400L high shear mixing vessel, 2012, Stainless, 2400l jacketed mixing vessel, top mounted agitation and scrape surface, central high shear mixing shaft, with centrifugal pump, 3Ph

Morgana PC50 Evaporator Serial: 1402055 Three fan, ceiling mounted evaporator, 3Ph

Fristam FP66-40 Centrifugal pump, Stainless, 12Kw, centrifugal pump, 3Ph

Dedy Chocolate shavings machine, Electric chocolate shavings machine, for blocks of 2.5kg - 5kg, 1Ph

Bartscher A120 Convection oven, 2012, stainless oven, up to 300,C, timer controls, four trays, 1Ph

Gami T240 Tempering machine, 2015, automatic continuous operation tempering machine for chocolate processing, 8Kg bowl capacity, 50Kg / H output, mobile, with vibratory table, with foot pedal, adjustable time and temperature control, 1Ph

Gami T240 Tempering machine, 2011, automatic continuous operation tempering machine for chocolate processing, 8Kg bowl capacity, 50Kg / H output, mobile, with vibratory table, with foot pedal, adjustable time and temperature control, 1Ph

MAX MAX-6B Industrial Microwave, 2018, Stainless, power 6Kw, Microwave frequency 2450mhz, temp range 0-300'C, variable speed, timer controls, with manual, mobile, 3Ph

Kronen GEWA3800V flume washer, Stainless flume washer, washes up to 1800Kg product per hour, twin water circulation pumps, vibro feeder dewatering, Suitable for washing vegetables, fruits, potatoes, fish and more, 3Ph

NNP Egg slicer Stainless, rotary egg slicer, pneumatic, 1Ph

Marco Linemaster IV scales stainless platform scales, weighing from 20g - 20,000g, platform 500mm x 400mm, mobile, 1Ph (two in stock)

Marco Linemaster IV scales, stainless platform scales, weighing from 20g - 20,000g, platform 600mm x 500mm, mobile, 1Ph (four in stock)

This Gimret UHT system is a continuous installation for sterilizing by heating, to ensure that a prepared liquid mixture is free from bacterial endospores, the mixture is passed through a sterilizer prior to the drying process. To obtain a continuous flow in the sterilizer, the material is first accommodated in a buffer tank from which the sterilizer is fed by using a dosing pump (low pressure). To kill the bacterial endospores a temperature of at least 135°C is required for a period of 5-7 seconds. To reach this temperature, steam is injected into the mixture that is dosed from the dosing pump. A meandering pipe works then realizes the required residence time at a set temperature of minimum 135°C.

Rollenbahnlänge: 3600 mm
Rollenbreite: 700 mm
Tischhöhe: 700 mm
Rollenbahnbreite: 900 mm
Rollendurchmesser: 140 mm
Tragkraft: kg
Anschlag: 450 mm
Antrieb: kW
Abmessung L-B-H: 3,7x0,9x1,3 m
Gewicht: 0,7 t

Rollenbahnlänge: 2900 mm
Rollenbreite: 700 mm
Tischhöhe: 700 mm
Rollenbahnbreite: 900 mm
Rollendurchmesser: 140 mm
Tragkraft: kg
Anschlag: 450 mm
Antrieb: kW
Abmessung L-B-H: 3,0x0,9x1,3 m
Gewicht: 0,7 t

Schnittdurchmesser: 1020 mm
Sägebandlänge: 11.430 x 80 x 1,6 mm
Schnittbreite: 1,6 mm
Schnittbereich: 1020x1260 mm
Steuerung: CNC
Schnittgeschwindigkeit: 15-190 m/min
Antriebsleistung: 11 kW
Tischbelastung: 20 t
Gesamtleistungsbedarf: 20 kW
Maschinengewicht ca.: 21,1 t
Raumbedarf ca.: m

x-Weg: 650 mm
y-Weg: 540 mm
z-Weg: 620 mm
Steuerung: Heidenhain
Typ: iTNC 530
Tischfläche: 800x540 mm
Werkzeugwechsler: 20 Pos
Spindelaufnahme ISO: 40
Drehzahl: 50-10.000 U/min
Kühlung durch die Spindel: 20 bar
Werkstückgewicht: 600 kg
Gesamtleistungsbedarf: 14 kW
Maschinengewicht ca.: 4,2 t
Raumbedarf ca.: 2,4x2,1x2,9 m

Spindeldurchmesser: 110 mm
x-Weg: 2000 mm
y-Weg: 1200 mm
Spindeldrehzahlen: 6-1250 U/min
Tischfläche: 1400x900 mm
Spindelantriebmotor: 12 kW
Spindelaufnahme ISO: 50
Spindelweg: 800 mm
z-Weg: 1000 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: 20 t
Raumbedarf ca.: 5x3x2 m

Saw frame: Double column
Band dimensions: 6800x41x1,3 mm
Band speed continous: 20-100 m/min
Cutting capacity 0° round: 560 mm
Cutting capacity 0° square: 540 mm
Cutting capacity 0° flat: 820x540 mm
Cutting capacity 45°: rund 550 mm, quadrat 540 mm, rechteck 550 x 540 mm
Cutting capacity 60°: rund 360 mm, quadrat 360 mm, rechteck 360 x 540 mm
Cutting capacity - 45°: rund 550 mm, quadrat 540 mm, rechteck 550 x 540 mm
Working height: 880 mm
Coolant pump motor: 0.12 kW
Hydraulic motor: 0.37 kW
Motor: 4 kW
Length: 3800 mm
Width: 1750 mm
Height: 2350 mm
Weight: 3200 kg

Cutting length: 2050 mm
Max. thickness - mild steel: 4 mm
Strokes: 42 1/min
Back gauge: 750 mm
Motor power: 7.5 kW
Table height: 800 mm
Table width: 450 mm
Length: 2700 mm
Width: 2300 mm
Height: 1350 mm
Weight: 2800 kg

Punching power: 110 ton
Throat depth: 500 mm
Max. diameter at sheet thickness (mild steel): 40x20 mm
Max. number of strokes at 20 mm stroke: 28 1/min
Motor: 9 kW
Length: 2080 mm
Width: 1300 mm
Height: 2050 mm
Weight: 3150 kg

Polar 76 EM

Chrome table with air
Several spare knives
Knife change tools

Machine in good condition

Ref. no.: 18383
Hersteller: DEMAG
Year of construction: 2008

Clamping unit
Clamping force: 420 ton
Opening stroke: 770 mm
Distance between tie bars: 820 X 820 mm
Mould height min.: 380 mm
Mould height max.: 825 mm
Platen size (h x v): 1200 X 1100 mm

Injection unit
Screw diameter: 60 mm
Injection volume: 890 cm³
Shot weight: 810 g
Injection pressure: 2420 bar

Measurements and weight
Dimensions: 8,2 X 2,2 X 2,4 m
Machine weight: 22300 kg

Additional information & extras
Core pull: 4 pcs
Air valve: 7 pcs
Hot runner systems: 8 pcs.

Robot
Producer: Remak
Year: 2008

Nilpeter FA 2400

Hot air drying + 4 UV units
Die cutting unit
Turning bar


Print Cylinders:

120 z x 6
117 z x 4
113 z x 5
110 z x 5
106 z x 5
102 z x 5
100 z x 5
96 z x 5
93 z x 5
90 z x 5
88 z x 5
84 z x 5
80 z x 6
76 z x 6
74 z x 4
72 z x 4
70 z x 6
68 z x 6
64 z x 5
62 z x 5
60 z x 5
58 z x 5

Print cilinder Shafts: 21

Anilox rollers:
180 - 9 pieces
140 - 6 pieces
120 - 9 pieces
320/5 - 2 pieces
80 R - 1 piece
GTTR 2 pieces

Rubber rollers 13

Ink trays: 10

Nilpeter F2400

3 color machine

Distance spindle - table: 730 mm
Table: 1200 x 600 mm
Grinding lenght: 1200 mm
Magnetic table: 1200 x 600 mm
Table movement hydraulic: 1300 mm
Table speed: 5 - 30 m/min
Cross feed: 0-2250 m/min
Cross feed incremental: 0,001-32 mm
Max. cross feed: 685 mm
Automatic vertical feed: 560 mm
Vertical feed: 0-675 mm/min
Spindle revs: 500-2200 rpm
Spindle motor: 11 kW
Hydraulic motor: 5.5 kW
Cross feed motor: 3.1 kW
Feed motor grinding wheel: 3.1 kW
Max. workpiece weight on magnetic table: 1150 kg
Max. workpiece weight on t-slot table: 1600 kg
Grinding wheel dimensions: 405 x 75 x 127 mm
Length: 4790 mm
Width: 3207 mm
Height: 2305 mm
Weight: 8100 kg

Swing over bed: 630 mm
Distance between centers: 2000 mm
Centre height: 315 mm
Spindle bore: 103 mm
swing over cross slide: 430 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 11
Spindle taper: 120 M
Spindle speed steps: 21
Spindle revs: Array rpm
Number of feeds: 120
Longitudinal feed range: 0.04 - 12 mm/r
Cross feed range: 0.02 - 6 mm/r
Metric thread range: 0.5 - 120 mm
Inch thread range: 60 - 1/4 Tpi
Module thread range: 0.125 - 30
DP thread range: Array
Cross slide travel: 315 mm
Top slide travel: 90 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 230 mm
Motor power: 11 kW
Weight: 3310 kg

Shaft diameter: 35
Upper roll diameter: 137 mm
Lower roll diameter: 137 mm
Driven rolls: 3
Motor power: 1.1 kW
Speed: 7 m/min
Flat steel vertical position (section / min. diameter): 35x8 mm / 300 mm
Flat steel horizontal position (section / min. diameter): 50x12 mm / 400 mm
Square bar (section / min. diameter): 18x18 mm / 250 mm
Round bar (section / min. diameter): Ø 22 mm / 200 mm
Tube (section / min. diameter): Ø 40x1,5 mm / 500 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 30x15x2,5 mm / 500 mm
Form tube square (section / min. diameter): 25x25x2 mm / 450 mm
Angle leg outside (Querschnitt / min. Durchmesser): 35x35x5 mm / 400 mm
Angle leg inside (section / min. diameter): 30x30x4 mm / 550 mm
Length: 1050 mm
Width: 500 mm
Height: 1250 mm
Weight: 350 kg

Shaft diameter: 30
Upper roll diameter: 148 mm
Lower roll diameter: 118 mm
Driven rolls: 2
Motor power: 0.7 / 0,85 kW
Speed: 2/4 m/min
Flat steel vertical position (section / min. diameter): 50x10 mm / 1.800 mm, 20x6 mm / 300 mm
Flat steel horizontal position (section / min. diameter): 80x15 mm / 700 mm, 30 x 6 mm / 400 mm
Square bar (section / min. diameter): 30x30 mm / 900 mm, 10x10 mm / 200 mm
Round bar (section / min. diameter): Ø 30 mm / 900 mm, Ø 10 mm / 200 mm
Tube (section / min. diameter): Ø 60x1,5 mm / 1.000 mm, Ø 25x1,5 mm / 600 mm, 1 1/2"x2,9 mm / 600 mm, 1/4"x1,8 mm / 300 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 50x30x3 mm / 1.200 mm, 40x20x2 mm / 800 mm
Form tube square (section / min. diameter): 40x40x3 mm / 1.200 mm, 30x30x2 mm / 800 mm
Angle leg outside (Querschnitt / min. Durchmesser): 40x40x5 mm / 600 mm, 30x30x4 mm / 300 mm
Angle leg inside (section / min. diameter): 35x35x5 mm / 600 mm, 30x30x4 mm / 400 mm
Length: 600 mm
Width: 800 mm
Height: 1450 mm
Weight: 220 kg

X-axis: 3000 mm
Positioning speed: 24 m/min
Repeat accuracy: 2 mm
Weight: 250 kg

Wohlenberg 115 CutTec paper cutting guillotine


Available immediately from stock.
Description:
– Positioning of items using the hand wheel
– Optimized cutting cycle
– Smoothly adjustable pressing pressure
– Automated knife change from the front
– Quick replacement of knives
– Machine body cast in one piece = higher stability

Technical data:
Cutting length: 1150 mm
Maximum stack height: 165 mm
Input depth: 1150 mm

Theisen en Bonitz Sprint B312 VP ( 2008)

Year: 2008
- 12 stations
– format: min. 7x10cm, max. 35x50cm
– paper weight: 18-800g/qm

Complete with QSM 304 stitching - folding- 3 side trimming unit
Equiped with hohner stithing heads
Loops stitching heads available

In mint condition !

Swing over bed: 760 mm
Distance between centers: 3000 mm
Centre height: 380 mm
Spindle bore: 132 mm
swing over cross slide: 520 mm
Width of bed: 560 mm
Spindle nose / DIN55027: 11
Spindle taper: 140 M
Revs continuous variable in gear steps: 3
Revs continuous variable: 7 - 42, 28 - 170, 165 - 1.015 rpm
Number of feeds: 150
Longitudinal feed range: 0.039 - 18 mm/r
Cross feed range: 0.02 - 9 mm/r
Metric thread range: 0.5 - 180 mm
Inch thread range: 60 - 1/6 Tpi
Module thread range: 0.125 - 45
DP thread range: Array
Cross slide travel: 410 mm
Top slide travel: 150 mm
Tailstock quill diameter: 105 mm
Tailstock quill taper: 6 MK
Tailstock travel: 225 mm
Motor power: 15 kW
Weight: 4470 kg

Swing over bed: 600 mm
Distance between centers: 2000 mm
Centre height: 300 mm
Spindle bore: 80 mm
swing over cross slide: 400 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 8
Spindle taper: 90 M
Revs continuous variable in gear steps: 3
Revs continuous variable: 8-62, 62-500, 250-2.000 rpm
Number of feeds: 160
Number of threads: 64
Metric thread range: 0.5 - 120 mm
Inch thread range: 120 - 1/4 Tpi
Module thread range: 0.125 - 30
Cross slide travel: 315 mm
Top slide travel: 130 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 230 mm
Motor power: 11 kW
Length: 3600 mm
Width: 1500 mm
Height: 1650 mm
Weight: 3110 kg

Karl tranklein kan 11 top gluer

Mkw 30ut/12

12 stations collating
Stitching folding trimming machine
Hohner stitching heads
Possible with loop stitching heads

Distance spindle - table: 445 mm
Table: 460 x 200 mm
Grinding lenght: 460 mm
Magnetic table: 450 x 200 mm
Table speed: 0,1 - 25 m/min
Cross feed: 0 - 3000 m/min
Max. cross feed: 220 mm
Automatic vertical feed: 340 mm
Vertical feed: 0 - 3000 mm/min
Vertical feed incremental: 0.001 mm
Spindle revs: 1000 - 7000 rpm
Spindle motor: 3 kW
Hydraulic motor: 0.7 kW
Cross feed motor: 1.1 kW
Feed motor grinding wheel: 1.1 kW
Table height: 1015 mm
Max. workpiece weight on magnetic table: 175 kg
Max. workpiece weight on t-slot table: 210 kg
Grinding wheel dimensions: Dm. 205 x 12,7 x 31,75 mm
Length: 2510 mm
Width: 2515 mm
Height: 2010 mm
Weight: 1550 kg

Bending length: 2050 mm
Max. bending capacity - mild steel: 10
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 10 mm
Max. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 8 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 8 mm
Max. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 6 mm
Upper roll diameter: 200 - 220 mm
Lower roll diameter: 200 - 220 mm
Lateral roll diameter: 160 mm
Bending speed: 1,5 / 6 m/min
Motor power: 5.5 kW
Length: 4400 mm
Width: 1150 mm
Height: 1250 mm
Weight: 3950 kg

Bending length: 2050 mm
Max. bending capacity - mild steel: 8
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 8 mm
Max. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 6 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 6 mm
Max. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 4 mm
Upper roll diameter: 180 mm
Lower roll diameter: 180 mm
Lateral roll diameter: 150 mm
Bending speed: 1,5 / 6 m/min
Motor power: 5.5 kW
Length: 4400 mm
Width: 1150 mm
Height: 1250 mm
Weight: 3790 kg

Saw frame: Double column
Band dimensions: 8200x41x1,3 mm
Band speed continous: 20-100 m/min
Cutting capacity 0° round: 810 mm
Cutting capacity 0° square: 750 mm
Cutting capacity 0° flat: 910x750 mm
Cutting capacity 45°: rund 600 mm, quadrat 600 mm, rechteck 750 x 600 mm
Cutting capacity 60°: rund 360 mm, quadrat 360 mm, rechteck 750 x 360 mm
Working height: 725 mm
Coolant pump motor: 0.12 kW
Motor: 4 kW
Length: 4020 mm
Width: 1600 mm
Height: 2450 mm
Weight: 3970 kg

Ref. no.: 18368
Hersteller: ARBURG
Year of construction: 1997

Clamping unit
Clamping force: 50 ton
Opening stroke: 350 mm
Distance between tie bars: 320 X 320 mm
Mould height min.: 300 mm
Mould height max.: 550 mm
Platen size (h x v): 446 X 446 mm

Injection unit
Screw diameter: 30 mm
Injection volume: 85 cm³
Shot weight: 75 g
Injection pressure: 2200 bar

Measurements and weight
Dimensions: 3,25 x 1.15 x 2,0 m
Machine weight: 2250 kg

Bending length: 4010 mm
Bending capacity steel 400 N/mm²: 1.5 mm
Bending capacity Alu 190 N/mm²: 2 mm
No. of stand and tension arm units: 4

Distance spindle - table: 850 mm
Table: 1000 x 600 mm
Grinding lenght: 1000 mm
Magnetic table: 1000 x 600 mm
Table movement hydraulic: 1000 mm
Table speed: 5 - 25 m/min
Cross feed: 1250 m/min
Max. cross feed: 690 mm
Automatic vertical feed: max. 400 mm/min mm
Vertical feed: 400 mm/min
Vertical feed incremental: 0.001 mm
Spindle revs: 1450 rpm
Spindle motor: 11 kW
Hydraulic motor: 3.7 kW
Cross feed motor: 0.37 kW
Total power: 20 kW
Maximal table load: 1500 kg
Max. workpiece weight on magnetic table: 1120 kg
Max. workpiece weight on t-slot table: 1500 kg
Grinding wheel dimensions: 355 x 75 x 127 mm
Length: 3700 mm
Width: 4000 mm
Height: 3250 mm
Weight: 7400 kg

Working width: 650
Sheet thickness range - mild steel: 0,5 - 170 mm
Grinding belt dimensions: 670 x 2200 mm
Suction capacity: 4000 m³/h
Connection for dust collector diam.: 120 mm
Air connection: 6 bar
Noise level: 83 dB
Motor: 22 kW
Length: 2600 mm
Width: 1350 mm
Height: 2100 mm
Weight: 1125 kg

Distance spindle - table: 600 mm
Table: 400 x 1000 mm
Grinding area: 1.015 x 405 x 610 mm
Grinding lenght: 1015 mm
Magnetic table: 1000 x 400 mm
Max. work piece weight: 670 kg
Table movement hydraulic: 1100 mm
Table speed: 5 - 25 m/min
Cross feed: 0 - 2,250 m/min
Cross feed incremental: 3 - 32 mm
Max. cross feed: 450 mm
Automatic vertical feed: 440 mm
Vertical feed: 0 - 675 mm/min
Vertical feed incremental: 0.001 - 0.04 mm
Spindle revs: 500 - 2.000 rpm
Spindle motor: 5 kW
Hydraulic motor: 1.5 kW
Cross feed motor: 1.1 kW
Feed motor grinding wheel: 1.1 kW
Max. workpiece weight on magnetic table: 423 kg
Max. workpiece weight on t-slot table: 670 kg
Grinding wheel dimensions: 355 x 50 x 127 mm
Length: 3630 mm
Width: 2682 mm
Height: 2200 mm
Transport dimensions: 4550 x 2280 x 2530 mm mm
Weight: 4800 kg

pressing capacity: 150 to
Cylinder fix or moveable: fix
Stroke: 300 mm
Daylight: 610 mm
Distance between columns: 1020 mm
Rapid speed: 9 mm/s
Working speed: 5 mm/s
Retraction speed: 10 mm/s
Table: 600x1020 mm
Hole in table: 100 mm
Hole distance: 190 mm
Length: 2110 mm
Width: 1000 mm
Height: 2470 mm
Weight: 2450 kg