Hache 1720E Turbidimeter, Hach 1720E Continuous-reading Nephelometric Low Range Process Turbidimeter, Continuously flowing sample flows through the patented bubble removal system, which vents entrained air from the sample stream and eliminates the most significant interference in low level turbidity measurement. The 1720E Turbidimeter is not affected by variations in flow and pressure, The 1720E Turbidimeter uses the sc200 Controller to receive data from up to two sensors. A built-in data logger collects turbidity measurement at user selectable intervals (1-15 minutes), along with calibration and verification points, alarm history, and instrument setup changes for 6 months.

Drilling capacy mild steel: 32 mm
Taper: MK 4
Distance spindle - column: 300 - 1.000 mm
Revs: 32 - 2.500 (16) r.p.m.
Distance table - spindle underside: 530 - 1.000 mm
Spindle motor: 2.2 kW
Column diameter: 240 mm
Quill travel: 250 mm
Feeds: 0,10 - 1,25 (8) mm/r
Length: 1760 mm
Width: 800 mm
Height: 2080 mm
Weight: 1600 kg

pressing capacity: 30 to
Tonnage rating point: 2 mm
Table length: 400 mm
Table width: 600 mm
Hole in table: 150 mm
Stroke: 1 - 60 mm
Strokes: 140 1/min
Ram guides: 4
Ram adjustment: 60 mm
Ram hole: 40 mm
Throat depth: 200 mm
Daylight: 300 mm
Motor: 3 kW
Length: 1300 mm
Width: 1150 mm
Height: 2050 mm
Weight: 1670 kg

Bending length: 1050 mm
Max. bending capacity - mild steel: 2.5
Max. plate thickness without prebending - mild steel: 2.5 mm
Max. plate thickness with prebending - mild steel: 2 mm
Upper roll diameter: 90 mm
Bending speed: 4 m/min
Motor power: 2.2 kW
Length: 2250 mm
Width: 1000 mm
Height: 1500 mm
Weight: 900 kg

Bending length: 1550 mm
Max. bending capacity - mild steel: 12
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 12 mm
Max. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 10 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 10 mm
Max. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 8 mm
Upper roll diameter: 220 mm
Lower roll diameter: 200 mm
Lateral roll diameter: 160 mm
Bending speed: 1,5 / 6 m/min
Motor power: 5.5 kW
Length: 3900 mm
Width: 1150 mm
Height: 1250 mm
Weight: 3600 kg

pressing capacity: 85 to
Stroke: 500 mm
Ram: 700x400 mm
Table: 800x600 mm
Daylight: 600 mm
Throat depth: 300 mm
Rapid speed: 105 mm/s
Reduced speed: 41 mm/s
Working speed: 7 mm/s
Retraction speed: 58 mm/s
Motor: 7.5 kW
Length: 1200 mm
Width: 1600 mm
Height: 2500 mm

pressing capacity: 60 to
Stroke: 500 mm
Ram: 700x350 mm
Table: 700x500 mm
Daylight: 600 mm
Throat depth: 250 mm
Rapid speed: 120 mm/s
Reduced speed: 38 mm/s
Working speed: 8 mm/s
Retraction speed: 58 mm/s
Motor: 5.5 kW
Length: 1100 mm
Width: 1500 mm
Height: 2350 mm

pressing capacity: 100 to
Stroke: 500 mm
Ram: 700 x 350 mm
Table: 800 x 600 mm
Daylight: 500 mm
Throat depth: 300 mm
Rapid speed: 25 mm/s
Working speed: 4 mm/s
Motor: 4 kW
Length: 1900 mm
Width: 1200 mm
Height: 2600 mm
Weight: 2100 kg

Load capacity: 2000kg
Gripping range: 1050-1200 mm
Suspension / size WxL: . 0
Own weight: 180 kg
Load capacity: 2 t
Span: . mm
Total power requirement: . kW
Machine weight approx.: . t
Space requirement approx.: . m

Load capacity: . kg
Gripping range: . mm
Suspension / size WxL: . 0
Own weight: . kg
Load capacity: . t
Span: . mm
Total power requirement: . kW
Machine weight approx.: . t
Space requirement approx.: . m

Diameter: . mm
Recording: .
Weight: . kg

Load capacity in kg: 2500 kg
Stroke: 2900mm
Fork length: . mm
Total power requirement: kW
Machine weight approx.: 3310 t
Space requirement approx.: m

Turning diameter: 820 mm
Turning length: 300mm
Turning diameter over support: 465 mm
Spindle torque: 3000 Nm
Speed: 5.6-1120 rpm
Feed: 1-5000mm/min
Rapid traverse: 5000 mm/min
Tailstock quill mount MK: 6
Three-jaw chuck Forckrath: mm
Bezel: mm
Main drive motor: 50 kW
Main spindle diameter: 170 mm
Spindle passage: 128 mm
Tailstock quill diameter: 125 mm
Tailstock quill stroke: 250 mm
z-axis: 3000 mm
x-axis: 550 mm
Total power requirement: 52 kW
Machine weight approx.: 7.1 t
Space requirement approx.: m

Label Producing BLUMER ATLAS 115,
complete line with die cutting unit D-18 and Bandrolling Machine PB 18.1 incl. strip feeder of Blumer and delivery table behind Blumer, size min: 25×45 mm, max. 150×180 mm,

Length: . mm
Height: . mm
Total power requirement: . kW
Machine weight approx.: . t
Space requirement approx.: . m

Number of floors: . 0
Width of floors: . mm
Depth of floors: . mm

Number of floors: . 0
Width of floors: . mm
Depth of floors: . mm

Cutting diameter: 150 mm
Saw blade length: . mm
Hub: . mm
Saw band length: . mm
Table height: . mm
Total power requirement: 0.5 kW
Machine weight approx.: . t
Space requirement approx.: . m

Diameter: . mm
Cutting (number): . 0
Weight: . kg

Diameter: mm
Cutting (count): 0
Weight: kg
Groove width: . mm
x-path: . mm
y-path: . mm
Total power requirement: . kW
Machine weight approx.: .. t
Space requirement approx.: . m