5
Food machinesMeat processing
Woods 56JM/20/4/6/10-36 flow extract fan, Year 2021, 560mm fan diameter, 1420 rev/min, see plate for spec, 5 in stock, 3Ph
Woods 56JM/20/4/6/10-36 flow extract fan, Year 2021, 560mm fan diameter, 1420 rev/min, see plate for spec, 5 in stock, 3Ph
7
Food machinesOther
DTB washing conveyor, Stainless, belt dimensions 1200mm x 300mm, with jet spray mounted on top of the conveyor with recirculation tank and pump for washing products, previously used for olives, 3Ph
DTB washing conveyor, Stainless, belt dimensions 1200mm x 300mm, with jet spray mounted on top of the conveyor with recirculation tank and pump for washing products, previously used for olives, 3Ph
3
Food machinesBeverage productionPumps
Grundfos CHI2-30 A-W-G Pump, 2010, 2900RPM, 2.5M3/H, rated head 19M, 19mm impeller, max operating pressure 10bar, 3Ph (two in stock)
Grundfos CHI2-30 A-W-G Pump, 2010, 2900RPM, 2.5M3/H, rated head 19M, 19mm impeller, max operating pressure 10bar, 3Ph (two in stock)
3
Food machinesMeat processing
Hache 1720E Turbidimeter, Hach 1720E Continuous-reading Nephelometric Low Range Process Turbidimeter, Continuously flowing sample flows through the patented bubble removal system, which vents entrained air from the sample stream and eliminates the most significant interference in low level turbidity measurement. The 1720E Turbidimeter is not affected by variations in flow and pressure, The 1720E Turbidimeter uses the sc200 Controller to receive data from up to two sensors. A built-in data logger collects turbidity measurement at user selectable intervals (1-15 minutes), along with calibration and verification points, alarm history, and instrument setup changes for 6 months.
Hache 1720E Turbidimeter, Hach 1720E Continuous-reading Nephelometric Low Range Process Turbidimeter, Continuously flowing sample flows through the patented bubble removal system, which vents entrained air from the sample stream and eliminates the most significant interference in low level turbidity measurement. The 1720E Turbidimeter is not affected by variations in flow and pressure, The 1720E Turbidimeter uses the sc200 Controller to receive data from up to two sensors. A built-in data logger collects turbidity measurement at user selectable intervals (1-15 minutes), along with calibration and verification points, alarm history, and instrument setup changes for 6 months.
6
Food machinesMeat processing
Europ-Plast VCPA315 centrifugal extraction fan, Serial: V9064, 2010, chemical resistant centrifugal extraction fan, 5.5Kw, all fans are manufacturered as direct drive assemblies and all casings are fully welded and come standard with chemical resistant vapor seals
Europ-Plast VCPA315 centrifugal extraction fan, Serial: V9064, 2010, chemical resistant centrifugal extraction fan, 5.5Kw, all fans are manufacturered as direct drive assemblies and all casings are fully welded and come standard with chemical resistant vapor seals
10
Food machinesMeat processing
Longwood D screen Fine screen, 2010, Dscreen simple design, operation and maintenance make it the ideal choice for reliable stand alone water filtration, fully enclosed unit, self cleaning screen, 0.8mm screens, Length 1200mm, width 1023mm, 0.37Kw motor, two available
Longwood D screen Fine screen, 2010, Dscreen simple design, operation and maintenance make it the ideal choice for reliable stand alone water filtration, fully enclosed unit, self cleaning screen, 0.8mm screens, Length 1200mm, width 1023mm, 0.37Kw motor, two available
8
Food machinesMeat processing
Longwood Rotapak150 Screw compactor, 2010, screw compactor, screenings handling equipment, screw diameter 150mm, capacity 0.5M3/hr, 1.5Kw motor, 3Ph
Longwood Rotapak150 Screw compactor, 2010, screw compactor, screenings handling equipment, screw diameter 150mm, capacity 0.5M3/hr, 1.5Kw motor, 3Ph
8
Food machinesBeverage productionPumps
Lowara 10HM02P11T5RVBE Multistage pump, Serial: 20170110, 2010, Horizontal multistage pump, mounted on stainless frame with Xylem flow meter, 1.23Kw, see plate for full spec
Lowara 10HM02P11T5RVBE Multistage pump, Serial: 20170110, 2010, Horizontal multistage pump, mounted on stainless frame with Xylem flow meter, 1.23Kw, see plate for full spec
6
Food machinesBeverage productionPumps
Sigma S2CAHM07120PVT Metering pump, Serial: 2010132518, 2010, 0.25Kw, Metering pumps, 3 in stock
Sigma S2CAHM07120PVT Metering pump, Serial: 2010132518, 2010, 0.25Kw, Metering pumps, 3 in stock
5
Food machinesContainers, shelves and tanks
Hoval Air receiver tank, 2010, capacity 500L, working temp -10'C to 45'C, max working pressure 10Bar,
Hoval Air receiver tank, 2010, capacity 500L, working temp -10'C to 45'C, max working pressure 10Bar,
8
Food machinesMeat processing
AVK Flanged gate valve, 2010, flanged gate valves with handwheels, 10+ in stock, various sizes
AVK Flanged gate valve, 2010, flanged gate valves with handwheels, 10+ in stock, various sizes
1
Metal working and machine toolsSheet metal working machinesSection steel shears
Punching power: 110 ton
Throat depth: 610 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 420/20 bzw. 28/28 mm
Stroke: 80 mm
Strokes: 28 1/min
Flat steel: 600x15 / 400x20 mm
Angle steel: 152x152x13 mm
Round / square steel: 50 mm
Notcher: 13x52x90 mm
Motor: 9 kW
Length: 2690 mm
Width: 1400 mm
Height: 2200 mm
Weight: 3300 kg
Punching power: 110 ton
Throat depth: 610 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 420/20 bzw. 28/28 mm
Stroke: 80 mm
Strokes: 28 1/min
Flat steel: 600x15 / 400x20 mm
Angle steel: 152x152x13 mm
Round / square steel: 50 mm
Notcher: 13x52x90 mm
Motor: 9 kW
Length: 2690 mm
Width: 1400 mm
Height: 2200 mm
Weight: 3300 kg
Throat depth: 610 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 420/20 bzw. 28/28 mm
Stroke: 80 mm
Strokes: 28 1/min
Flat steel: 600x15 / 400x20 mm
Angle steel: 152x152x13 mm
Round / square steel: 50 mm
Notcher: 13x52x90 mm
Motor: 9 kW
Length: 2690 mm
Width: 1400 mm
Height: 2200 mm
Weight: 3300 kg
9
Metal working and machine toolsSheet metal working machinesSwivel bending machines
Bending length: 4010 mm
Bending capacity steel 400 N/mm²: 1.25 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.25 mm
No. of stand and tension arm units: 4
No. of driven linkage assemblies: 4
Sheet insertion depth: 1000 mm
Opening of upper beam: 190 mm
Working height: 835 mm
Motor: 2.2 kW
Length with electrical shear: 5200 mm
Width: 1300 mm
Height: 1900 mm
Weight: 1550 kg
Bending length: 4010 mm
Bending capacity steel 400 N/mm²: 1.25 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.25 mm
No. of stand and tension arm units: 4
No. of driven linkage assemblies: 4
Sheet insertion depth: 1000 mm
Opening of upper beam: 190 mm
Working height: 835 mm
Motor: 2.2 kW
Length with electrical shear: 5200 mm
Width: 1300 mm
Height: 1900 mm
Weight: 1550 kg
Bending capacity steel 400 N/mm²: 1.25 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.25 mm
No. of stand and tension arm units: 4
No. of driven linkage assemblies: 4
Sheet insertion depth: 1000 mm
Opening of upper beam: 190 mm
Working height: 835 mm
Motor: 2.2 kW
Length with electrical shear: 5200 mm
Width: 1300 mm
Height: 1900 mm
Weight: 1550 kg
5
Metal working and machine toolsSawingBelt saws
Saw frame: Pivot frame
Band dimensions: 4160x34x1,1 mm
Band speed continous: 15 - 120 m/min
Cutting capacity 0° round: 320 mm
Cutting capacity 0° square: 320 mm
Cutting capacity 0° flat: 450x320 mm
Cutting capacity 30°: round 320 mm, square 320 mm, rectangular 380x320 mm
Cutting capacity 45°: round 320 mm, square 320 mm, rectangular 330x320 mm
Cutting capacity - 30°: round 320 mm, square 320 mm, rectangular 380x320 mm
Cutting capacity - 45°: round 320 mm, square 300 mm, rectangular 340x320 mm
Cutting capacity - 60°: round 230 mm, square 220 mm, rectangular 230x220 mm
Working height: 860 mm
Hydraulic motor: 0.37 kW
Motor: 2.2 kW
Coolant pump motor: 0.12 kW
Length: 2230 mm
Width: 1150 mm
Height: 2140 mm
Weight: 1030 kg
Saw frame: Pivot frame
Band dimensions: 4160x34x1,1 mm
Band speed continous: 15 - 120 m/min
Cutting capacity 0° round: 320 mm
Cutting capacity 0° square: 320 mm
Cutting capacity 0° flat: 450x320 mm
Cutting capacity 30°: round 320 mm, square 320 mm, rectangular 380x320 mm
Cutting capacity 45°: round 320 mm, square 320 mm, rectangular 330x320 mm
Cutting capacity - 30°: round 320 mm, square 320 mm, rectangular 380x320 mm
Cutting capacity - 45°: round 320 mm, square 300 mm, rectangular 340x320 mm
Cutting capacity - 60°: round 230 mm, square 220 mm, rectangular 230x220 mm
Working height: 860 mm
Hydraulic motor: 0.37 kW
Motor: 2.2 kW
Coolant pump motor: 0.12 kW
Length: 2230 mm
Width: 1150 mm
Height: 2140 mm
Weight: 1030 kg
Band dimensions: 4160x34x1,1 mm
Band speed continous: 15 - 120 m/min
Cutting capacity 0° round: 320 mm
Cutting capacity 0° square: 320 mm
Cutting capacity 0° flat: 450x320 mm
Cutting capacity 30°: round 320 mm, square 320 mm, rectangular 380x320 mm
Cutting capacity 45°: round 320 mm, square 320 mm, rectangular 330x320 mm
Cutting capacity - 30°: round 320 mm, square 320 mm, rectangular 380x320 mm
Cutting capacity - 45°: round 320 mm, square 300 mm, rectangular 340x320 mm
Cutting capacity - 60°: round 230 mm, square 220 mm, rectangular 230x220 mm
Working height: 860 mm
Hydraulic motor: 0.37 kW
Motor: 2.2 kW
Coolant pump motor: 0.12 kW
Length: 2230 mm
Width: 1150 mm
Height: 2140 mm
Weight: 1030 kg
2
Metal working and machine toolsSawingBelt saws
Saw frame: Double column
Band dimensions: 5750 x 41 x 1,3 mm
Band speed continous: 15 - 120 m/min
Cutting capacity 0° round: 420 mm
Cutting capacity 0° square: 420 mm
Cutting capacity 0° flat: 420 x 420 mm
Working height: 805 mm
Hydraulic motor: 1.1 kW
Motor: 5.5 kW
Servomotor: 1 kW
Coolant pump motor: 0.12 kW
Length: 2860 mm
Width: 1980 mm
Height: 2100 mm
Weight: 3700 kg
Saw frame: Double column
Band dimensions: 5750 x 41 x 1,3 mm
Band speed continous: 15 - 120 m/min
Cutting capacity 0° round: 420 mm
Cutting capacity 0° square: 420 mm
Cutting capacity 0° flat: 420 x 420 mm
Working height: 805 mm
Hydraulic motor: 1.1 kW
Motor: 5.5 kW
Servomotor: 1 kW
Coolant pump motor: 0.12 kW
Length: 2860 mm
Width: 1980 mm
Height: 2100 mm
Weight: 3700 kg
Band dimensions: 5750 x 41 x 1,3 mm
Band speed continous: 15 - 120 m/min
Cutting capacity 0° round: 420 mm
Cutting capacity 0° square: 420 mm
Cutting capacity 0° flat: 420 x 420 mm
Working height: 805 mm
Hydraulic motor: 1.1 kW
Motor: 5.5 kW
Servomotor: 1 kW
Coolant pump motor: 0.12 kW
Length: 2860 mm
Width: 1980 mm
Height: 2100 mm
Weight: 3700 kg
3
Printing machineryLabel printing and die-cutting machine
Cauhe VA (1450 x 1850 mm) Die Cutter / Cauhe VA Heavy-Duty Large Format Die Cutter
Very neat machine, rarely used.
Max format: (1450 x 1850 mm)
Model: VA
Year: 2008
Available immediately!
Cauhe VA (1450 x 1850 mm) Die Cutter / Cauhe VA Heavy-Duty Large Format Die Cutter
Very neat machine, rarely used.
Max format: (1450 x 1850 mm)
Model: VA
Year: 2008
Available immediately!
Very neat machine, rarely used.
Max format: (1450 x 1850 mm)
Model: VA
Year: 2008
Available immediately!
7
Metal working and machine toolsSheet metal working machinesSwivel bending machines
Bending length: 2040 mm
Sheet thickness (420 N/mm²): 3 mm
Max. thickness - stainless steel: 2 mm
Max. thickness - aluminium: 4.5 mm
Antrieb: Motorized
Motor bending beam: 1.5 kW
Upper beam motor: 1.1 kW
Back gauge: 750 mm
Opening of upper beam: 140 mm
Bending speed: 50 °/sek
Length: 3060 mm
Width: 1650 mm
Height: 1500 mm
Weight: 2730 kg
Bending length: 2040 mm
Sheet thickness (420 N/mm²): 3 mm
Max. thickness - stainless steel: 2 mm
Max. thickness - aluminium: 4.5 mm
Antrieb: Motorized
Motor bending beam: 1.5 kW
Upper beam motor: 1.1 kW
Back gauge: 750 mm
Opening of upper beam: 140 mm
Bending speed: 50 °/sek
Length: 3060 mm
Width: 1650 mm
Height: 1500 mm
Weight: 2730 kg
Sheet thickness (420 N/mm²): 3 mm
Max. thickness - stainless steel: 2 mm
Max. thickness - aluminium: 4.5 mm
Antrieb: Motorized
Motor bending beam: 1.5 kW
Upper beam motor: 1.1 kW
Back gauge: 750 mm
Opening of upper beam: 140 mm
Bending speed: 50 °/sek
Length: 3060 mm
Width: 1650 mm
Height: 1500 mm
Weight: 2730 kg
9
Compressed-air technologyPumps
For Sale: 2x Gardner Denver DLR 300 Pumps with Control Cabinet and Mounting Plates
Brand/Model: Elmo Rietschle / Gardner Denver DLR 300
Year of Manufacture: 2010
Capacity: 300 m³/hour
Pressure: 1.4 bar
Power: 11 kW per pump
Year: 2010
Includes:
Control cabinet with Siemens S7 PLC and pre-installed program
2x Danfoss VLT frequency regulators (11 kW each)
2 mounting plates for pump installation
Condition: Removed in working condition from an industrial facility
A well-maintained set, ideal for various industrial applications.
📩 Contact us for pricing and more details!
For Sale: 2x Gardner Denver DLR 300 Pumps with Control Cabinet and Mounting Plates
Brand/Model: Elmo Rietschle / Gardner Denver DLR 300
Year of Manufacture: 2010
Capacity: 300 m³/hour
Pressure: 1.4 bar
Power: 11 kW per pump
Year: 2010
Includes:
Control cabinet with Siemens S7 PLC and pre-installed program
2x Danfoss VLT frequency regulators (11 kW each)
2 mounting plates for pump installation
Condition: Removed in working condition from an industrial facility
A well-maintained set, ideal for various industrial applications.
📩 Contact us for pricing and more details!
Brand/Model: Elmo Rietschle / Gardner Denver DLR 300
Year of Manufacture: 2010
Capacity: 300 m³/hour
Pressure: 1.4 bar
Power: 11 kW per pump
Year: 2010
Includes:
Control cabinet with Siemens S7 PLC and pre-installed program
2x Danfoss VLT frequency regulators (11 kW each)
2 mounting plates for pump installation
Condition: Removed in working condition from an industrial facility
A well-maintained set, ideal for various industrial applications.
📩 Contact us for pricing and more details!
8
Printing machineryPost press machinesLaminating machines
D&K Europa System B2 Laminator automatic laminating machine
Technical data:
Max sheet size: 540mm x 740mm
Min sheet size: 210mm x 220mm
Min grammage: 115 gsm
Max grammage: 400 gsm
Operating temperature: 80-145°C
Weight: 750 kg
Power supply 380V
Steel, chrome-plated cylinder
Pneumatic pressure, separation and automatic feeding from a high stack.
Sheet feeding accuracy: ±2.0mm.
Touch panel for easy operation.
Sheet straightening module.
D&K Europa System B2 Laminator automatic laminating machine
Technical data:
Max sheet size: 540mm x 740mm
Min sheet size: 210mm x 220mm
Min grammage: 115 gsm
Max grammage: 400 gsm
Operating temperature: 80-145°C
Weight: 750 kg
Power supply 380V
Steel, chrome-plated cylinder
Pneumatic pressure, separation and automatic feeding from a high stack.
Sheet feeding accuracy: ±2.0mm.
Touch panel for easy operation.
Sheet straightening module.
Technical data:
Max sheet size: 540mm x 740mm
Min sheet size: 210mm x 220mm
Min grammage: 115 gsm
Max grammage: 400 gsm
Operating temperature: 80-145°C
Weight: 750 kg
Power supply 380V
Steel, chrome-plated cylinder
Pneumatic pressure, separation and automatic feeding from a high stack.
Sheet feeding accuracy: ±2.0mm.
Touch panel for easy operation.
Sheet straightening module.
3
Metal working and machine toolsSheet metal working machinesFeed straighteners
Min. coil inner diameter: 400 mm
Max. Coil inner diameter: 700
Max. coil width: 1500 mm
Length: 2050 mm
Width: 820 mm
Height: 1000 mm
Min. coil inner diameter: 400 mm
Max. Coil inner diameter: 700
Max. coil width: 1500 mm
Length: 2050 mm
Width: 820 mm
Height: 1000 mm
Max. Coil inner diameter: 700
Max. coil width: 1500 mm
Length: 2050 mm
Width: 820 mm
Height: 1000 mm
3
Metal working and machine toolsDrilling machines and boring mills
Drilling capacy mild steel: 30 mm
Taper: MK 3
Distance spindle - column: 250 mm
Revs: 245 - 4000 r.p.m.
Tapping capacity: M25
max. drilling depth: 120 mm
Column diameter: 100 mm
Distance spindle - table: 85 - 635 mm
Distance spindle-base: 1.195 mm
Table: 300 x 270 mm
Base dimensions: 600 x 380 mm
Length: 400 mm
Width: 655 mm
Height: 1185 mm
Weight: 280 kg
Drilling capacy mild steel: 30 mm
Taper: MK 3
Distance spindle - column: 250 mm
Revs: 245 - 4000 r.p.m.
Tapping capacity: M25
max. drilling depth: 120 mm
Column diameter: 100 mm
Distance spindle - table: 85 - 635 mm
Distance spindle-base: 1.195 mm
Table: 300 x 270 mm
Base dimensions: 600 x 380 mm
Length: 400 mm
Width: 655 mm
Height: 1185 mm
Weight: 280 kg
Taper: MK 3
Distance spindle - column: 250 mm
Revs: 245 - 4000 r.p.m.
Tapping capacity: M25
max. drilling depth: 120 mm
Column diameter: 100 mm
Distance spindle - table: 85 - 635 mm
Distance spindle-base: 1.195 mm
Table: 300 x 270 mm
Base dimensions: 600 x 380 mm
Length: 400 mm
Width: 655 mm
Height: 1185 mm
Weight: 280 kg
12
Metal working and machine toolsLathesOther
MEPAC PCA 01 / Abdreh - Poliermaschine
-CE Kennung
-Baujahr 2022
-Spitzenhöhe 250mm
-Dreibackenfutter 120mm
-Wechselbacken
Caopv0E3V0
-Rollbarer Unterschrank
-Stufenlose Drehzahlregulierung
-Drehzahlrichtung Rechts / Links
-Not / Aus
Abmaße:
LxBxH 0,8x0,9x1,5 Meter / Gewicht 100 Kg
MEPAC PCA 01 / Abdreh - Poliermaschine
-CE Kennung
-Baujahr 2022
-Spitzenhöhe 250mm
-Dreibackenfutter 120mm
-Wechselbacken
Caopv0E3V0
-Rollbarer Unterschrank
-Stufenlose Drehzahlregulierung
-Drehzahlrichtung Rechts / Links
-Not / Aus
Abmaße:
LxBxH 0,8x0,9x1,5 Meter / Gewicht 100 Kg
-CE Kennung
-Baujahr 2022
-Spitzenhöhe 250mm
-Dreibackenfutter 120mm
-Wechselbacken
Caopv0E3V0
-Rollbarer Unterschrank
-Stufenlose Drehzahlregulierung
-Drehzahlrichtung Rechts / Links
-Not / Aus
Abmaße:
LxBxH 0,8x0,9x1,5 Meter / Gewicht 100 Kg
3
Metal working and machine toolsOther
Mobile Scherenhubbühne Rothe Benkmann<br />Bauhöhe 2,6m<br />Podesthöhe eingefahren ca. 1,6 Meter<br />Gesamthöhe ausgefahren 3,4 m<br />Tragkraft:2000kg<br />Eigengewicht 900Kg<br />Transportrollen können angebracht werden
Mobile Scherenhubbühne Rothe Benkmann<br />Bauhöhe 2,6m<br />Podesthöhe eingefahren ca. 1,6 Meter<br />Gesamthöhe ausgefahren 3,4 m<br />Tragkraft:2000kg<br />Eigengewicht 900Kg<br />Transportrollen können angebracht werden
9
Metal working and machine toolsSawingBelt saws
Knuth VB 510 / Vertikalbandsäge
-CE Kennung
-Baujahr 2008
-Bandschweißeinrichtung
-Stufenlose Drehzahlregulierung
-Tischabmessung 600x500mm
-Arbeitsleuchte
-Maschinenfüße
-Diverses Zubehör
Abmaße:
LxBxH 1,2x0,7x2 Meter / Gewicht 500Kg
Drgwcd
Knuth VB 510 / Vertikalbandsäge
-CE Kennung
-Baujahr 2008
-Bandschweißeinrichtung
-Stufenlose Drehzahlregulierung
-Tischabmessung 600x500mm
-Arbeitsleuchte
-Maschinenfüße
-Diverses Zubehör
Abmaße:
LxBxH 1,2x0,7x2 Meter / Gewicht 500Kg
Drgwcd
-CE Kennung
-Baujahr 2008
-Bandschweißeinrichtung
-Stufenlose Drehzahlregulierung
-Tischabmessung 600x500mm
-Arbeitsleuchte
-Maschinenfüße
-Diverses Zubehör
Abmaße:
LxBxH 1,2x0,7x2 Meter / Gewicht 500Kg
Drgwcd
5
Metal working and machine toolsSawingBelt saws
Saw frame: Double column
Band dimensions: 5000 x 34 x 1,1 mm mm
Band speed continous: 20 - 120 m/min
Cutting capacity 0° round: 330 mm
Cutting capacity 0° square: 330 mm
Cutting capacity 0° flat: 350 x 330 mm
Working height: 845 mm
Hydraulic motor: 1.1 kW
Motor: 3 kW
Coolant pump motor: 0.12 kW
Length: 2815 mm
Width: 1935 mm
Height: 1855 mm
Weight: 2560 kg
Saw frame: Double column
Band dimensions: 5000 x 34 x 1,1 mm mm
Band speed continous: 20 - 120 m/min
Cutting capacity 0° round: 330 mm
Cutting capacity 0° square: 330 mm
Cutting capacity 0° flat: 350 x 330 mm
Working height: 845 mm
Hydraulic motor: 1.1 kW
Motor: 3 kW
Coolant pump motor: 0.12 kW
Length: 2815 mm
Width: 1935 mm
Height: 1855 mm
Weight: 2560 kg
Band dimensions: 5000 x 34 x 1,1 mm mm
Band speed continous: 20 - 120 m/min
Cutting capacity 0° round: 330 mm
Cutting capacity 0° square: 330 mm
Cutting capacity 0° flat: 350 x 330 mm
Working height: 845 mm
Hydraulic motor: 1.1 kW
Motor: 3 kW
Coolant pump motor: 0.12 kW
Length: 2815 mm
Width: 1935 mm
Height: 1855 mm
Weight: 2560 kg
8
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18482
Hersteller: KRAUSS MAFFEI
Year of construction: 2010
Clamping unit
Clamping force: 300 ton
Opening stroke: 820 mm
Distance between tie bars: 810 X 720 mm
Mould height min.: 480 mm
Opening width: 1300 mm
Injection unit
Screw diameter: 60 mm
Injection volume: 792 cm³
Shot weight: 720 g
Injection pressure: 2420 bar
Measurements and weight
Dimensions: 6,7 X 2,1 X 2,4 m
Machine weight: 16400 kg
Additional information & extras
Accumulator: 1 pcs
Robot
Producer: Krauss Maffei
Type: KM LRX S 250
Year: 2010
Ref. no.: 18482
Hersteller: KRAUSS MAFFEI
Year of construction: 2010
Clamping unit
Clamping force: 300 ton
Opening stroke: 820 mm
Distance between tie bars: 810 X 720 mm
Mould height min.: 480 mm
Opening width: 1300 mm
Injection unit
Screw diameter: 60 mm
Injection volume: 792 cm³
Shot weight: 720 g
Injection pressure: 2420 bar
Measurements and weight
Dimensions: 6,7 X 2,1 X 2,4 m
Machine weight: 16400 kg
Additional information & extras
Accumulator: 1 pcs
Robot
Producer: Krauss Maffei
Type: KM LRX S 250
Year: 2010
Hersteller: KRAUSS MAFFEI
Year of construction: 2010
Clamping unit
Clamping force: 300 ton
Opening stroke: 820 mm
Distance between tie bars: 810 X 720 mm
Mould height min.: 480 mm
Opening width: 1300 mm
Injection unit
Screw diameter: 60 mm
Injection volume: 792 cm³
Shot weight: 720 g
Injection pressure: 2420 bar
Measurements and weight
Dimensions: 6,7 X 2,1 X 2,4 m
Machine weight: 16400 kg
Additional information & extras
Accumulator: 1 pcs
Robot
Producer: Krauss Maffei
Type: KM LRX S 250
Year: 2010
4
Metal working and machine toolsSawingBelt saws
Saw frame: Double column
Band dimensions: 5750 x 41 x 1,3 mm
Band speed continous: 15 - 120 m/min
Cutting capacity 0° round: 460 mm
Cutting capacity 0° square: 460 mm
Cutting capacity 0° flat: 520 x 460 mm
Working height: 585 mm
Hydraulic motor: 0.55 kW
Motor: 4 kW
Coolant pump motor: 0.12 kW
Length: 3000 mm
Width: 1200 mm
Height: 1800 mm
Weight: 1650 kg
Saw frame: Double column
Band dimensions: 5750 x 41 x 1,3 mm
Band speed continous: 15 - 120 m/min
Cutting capacity 0° round: 460 mm
Cutting capacity 0° square: 460 mm
Cutting capacity 0° flat: 520 x 460 mm
Working height: 585 mm
Hydraulic motor: 0.55 kW
Motor: 4 kW
Coolant pump motor: 0.12 kW
Length: 3000 mm
Width: 1200 mm
Height: 1800 mm
Weight: 1650 kg
Band dimensions: 5750 x 41 x 1,3 mm
Band speed continous: 15 - 120 m/min
Cutting capacity 0° round: 460 mm
Cutting capacity 0° square: 460 mm
Cutting capacity 0° flat: 520 x 460 mm
Working height: 585 mm
Hydraulic motor: 0.55 kW
Motor: 4 kW
Coolant pump motor: 0.12 kW
Length: 3000 mm
Width: 1200 mm
Height: 1800 mm
Weight: 1650 kg
1
Metal working and machine toolsSheet metal working machinesSection steel shears
Punching power: 55 ton
Throat depth: 250 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/10 mm
Stroke: 20 mm
Strokes: 37 1/min
Flat steel: 300x15 mm
Angle steel: 120x10 mm
Round / square steel: 40 mm
Notcher: 10 mm
Motor: 5 kW
Length: 1670 mm
Width: 1160 mm
Height: 2090 mm
Weight: 1390 kg
Punching power: 55 ton
Throat depth: 250 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/10 mm
Stroke: 20 mm
Strokes: 37 1/min
Flat steel: 300x15 mm
Angle steel: 120x10 mm
Round / square steel: 40 mm
Notcher: 10 mm
Motor: 5 kW
Length: 1670 mm
Width: 1160 mm
Height: 2090 mm
Weight: 1390 kg
Throat depth: 250 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/10 mm
Stroke: 20 mm
Strokes: 37 1/min
Flat steel: 300x15 mm
Angle steel: 120x10 mm
Round / square steel: 40 mm
Notcher: 10 mm
Motor: 5 kW
Length: 1670 mm
Width: 1160 mm
Height: 2090 mm
Weight: 1390 kg
3
Metal working and machine toolsSheet metal working machinesPress brakes
pressing capacity: 100 to
Bending length: 1500 mm
Stroke: 300 mm
Motor power: 7.5 kW
Die: 1
Distance between table and toolholder: 680 mm
Distance between columns: 1520 mm
Working speed: 5 mm/s
Rapid speed: 10 mm/s
Max. bending capacity (mild steel): 6 mm
Hole in table: 100 mm
Hole distance: 190 mm
Length: 2630 mm
Width: 1000 mm
Height: 2275 mm
Weight: 2500 kg
pressing capacity: 100 to
Bending length: 1500 mm
Stroke: 300 mm
Motor power: 7.5 kW
Die: 1
Distance between table and toolholder: 680 mm
Distance between columns: 1520 mm
Working speed: 5 mm/s
Rapid speed: 10 mm/s
Max. bending capacity (mild steel): 6 mm
Hole in table: 100 mm
Hole distance: 190 mm
Length: 2630 mm
Width: 1000 mm
Height: 2275 mm
Weight: 2500 kg
Bending length: 1500 mm
Stroke: 300 mm
Motor power: 7.5 kW
Die: 1
Distance between table and toolholder: 680 mm
Distance between columns: 1520 mm
Working speed: 5 mm/s
Rapid speed: 10 mm/s
Max. bending capacity (mild steel): 6 mm
Hole in table: 100 mm
Hole distance: 190 mm
Length: 2630 mm
Width: 1000 mm
Height: 2275 mm
Weight: 2500 kg
1
Metal working and machine toolsSheet metal working machinesRound rolling machines
Bending length: 3030 mm
Max. bending capacity - mild steel: 6
Max. plate thickness without prebending - mild steel: 6 mm
Max. plate thickness with prebending - mild steel: 4 mm
Upper roll diameter: 220 mm
Motor power: 5.5 kW
Length: 4750 mm
Width: 1200 mm
Height: 1150 mm
Weight: 4920 kg
Bending length: 3030 mm
Max. bending capacity - mild steel: 6
Max. plate thickness without prebending - mild steel: 6 mm
Max. plate thickness with prebending - mild steel: 4 mm
Upper roll diameter: 220 mm
Motor power: 5.5 kW
Length: 4750 mm
Width: 1200 mm
Height: 1150 mm
Weight: 4920 kg
Max. bending capacity - mild steel: 6
Max. plate thickness without prebending - mild steel: 6 mm
Max. plate thickness with prebending - mild steel: 4 mm
Upper roll diameter: 220 mm
Motor power: 5.5 kW
Length: 4750 mm
Width: 1200 mm
Height: 1150 mm
Weight: 4920 kg
1
Metal working and machine toolsSheet metal working machinesRound rolling machines
Bending length: 2530 mm
Max. bending capacity - mild steel: 6
Max. plate thickness without prebending - mild steel: 6 mm
Max. plate thickness with prebending - mild steel: 4 mm
Upper roll diameter: 190 mm
Motor power: 5.5 kW
Length: 4250 mm
Width: 1200 mm
Height: 1150 mm
Weight: 3750 kg
Bending length: 2530 mm
Max. bending capacity - mild steel: 6
Max. plate thickness without prebending - mild steel: 6 mm
Max. plate thickness with prebending - mild steel: 4 mm
Upper roll diameter: 190 mm
Motor power: 5.5 kW
Length: 4250 mm
Width: 1200 mm
Height: 1150 mm
Weight: 3750 kg
Max. bending capacity - mild steel: 6
Max. plate thickness without prebending - mild steel: 6 mm
Max. plate thickness with prebending - mild steel: 4 mm
Upper roll diameter: 190 mm
Motor power: 5.5 kW
Length: 4250 mm
Width: 1200 mm
Height: 1150 mm
Weight: 3750 kg
1
Metal working and machine toolsSheet metal working machinesRound rolling machines
Bending length: 3030 mm
Max. bending capacity - mild steel: 4
Max. plate thickness without prebending - mild steel: 4 mm
Max. plate thickness with prebending - mild steel: 2 mm
Upper roll diameter: 180 mm
Motor power: 4 kW
Length: 4600 mm
Width: 1120 mm
Height: 1020 mm
Weight: 4250 kg
Bending length: 3030 mm
Max. bending capacity - mild steel: 4
Max. plate thickness without prebending - mild steel: 4 mm
Max. plate thickness with prebending - mild steel: 2 mm
Upper roll diameter: 180 mm
Motor power: 4 kW
Length: 4600 mm
Width: 1120 mm
Height: 1020 mm
Weight: 4250 kg
Max. bending capacity - mild steel: 4
Max. plate thickness without prebending - mild steel: 4 mm
Max. plate thickness with prebending - mild steel: 2 mm
Upper roll diameter: 180 mm
Motor power: 4 kW
Length: 4600 mm
Width: 1120 mm
Height: 1020 mm
Weight: 4250 kg
8
Printing machineryPrinting machines
Polar RA 2 vibration table
Year of construction: 2008
With extortion
The Polar RA 2 vibrating table is an essential addition to any print shop that strives for maximum efficiency and precision in paper handling. With a size of 72×87 cm, this vibrating table offers enough space to align large stacks of paper quickly and evenly, ensuring flawless processing in subsequent processes.
Key Features:
Air-Driven Roller : The built-in air-pressure roller helps distribute the paper evenly, resulting in a perfectly aligned stack without damage.
Maximum Stack Height of 16.5 cm : The Polar RA 2 can handle stacks up to 16.5 cm high, meaning fewer interruptions and higher productivity.
Chrome Blower Plate : The chrome blower plate reduces friction and protects the paper, while the integrated blowers provide efficient and precise air delivery.
Automatic side flaps :
This vibrating table is ideal for printers and paper converting companies that strive for perfection and reliability in their production processes. The Polar RA 2 ensures consistent quality and optimizes the workflow, saving you time and costs.
Polar RA 2 vibration table
Year of construction: 2008
With extortion
The Polar RA 2 vibrating table is an essential addition to any print shop that strives for maximum efficiency and precision in paper handling. With a size of 72×87 cm, this vibrating table offers enough space to align large stacks of paper quickly and evenly, ensuring flawless processing in subsequent processes.
Key Features:
Air-Driven Roller : The built-in air-pressure roller helps distribute the paper evenly, resulting in a perfectly aligned stack without damage.
Maximum Stack Height of 16.5 cm : The Polar RA 2 can handle stacks up to 16.5 cm high, meaning fewer interruptions and higher productivity.
Chrome Blower Plate : The chrome blower plate reduces friction and protects the paper, while the integrated blowers provide efficient and precise air delivery.
Automatic side flaps :
This vibrating table is ideal for printers and paper converting companies that strive for perfection and reliability in their production processes. The Polar RA 2 ensures consistent quality and optimizes the workflow, saving you time and costs.
Year of construction: 2008
With extortion
The Polar RA 2 vibrating table is an essential addition to any print shop that strives for maximum efficiency and precision in paper handling. With a size of 72×87 cm, this vibrating table offers enough space to align large stacks of paper quickly and evenly, ensuring flawless processing in subsequent processes.
Key Features:
Air-Driven Roller : The built-in air-pressure roller helps distribute the paper evenly, resulting in a perfectly aligned stack without damage.
Maximum Stack Height of 16.5 cm : The Polar RA 2 can handle stacks up to 16.5 cm high, meaning fewer interruptions and higher productivity.
Chrome Blower Plate : The chrome blower plate reduces friction and protects the paper, while the integrated blowers provide efficient and precise air delivery.
Automatic side flaps :
This vibrating table is ideal for printers and paper converting companies that strive for perfection and reliability in their production processes. The Polar RA 2 ensures consistent quality and optimizes the workflow, saving you time and costs.
5
Metal working and machine toolsCutting machines and equipmentLaser cutting machines
Laser power: 6 kW
Manual table / shuttle table: Manual table
Max. thickness - mild steel: 20 mm
Max. thickness - stainless steel: 15 mm
Max. thickness - aluminium: 20 mm
Max. Application Range - Copper: 10 mm
Max. Application Range - Brass: 12 mm
Cutting area: 3.048 x 1.530 mm
X-axis: 3048 mm
Y-axis: 1530 mm
Z-Axis: 125 mm
Max. Sheet size: 3.048 x 1.524 mm
Max. sheet weight: 127 kg/m²
Max speed x-axes: 90 m/min
Max speed y-axes: 90 m/min
Max. speed simultaneous: 127 m/min
Max. acceleration: 14 m/s²
Positioning accuracy: +/- 0,05 mm
Repeat accuracy: +/- 0,05 mm
Weight: 6600 kg
Laser power: 6 kW
Manual table / shuttle table: Manual table
Max. thickness - mild steel: 20 mm
Max. thickness - stainless steel: 15 mm
Max. thickness - aluminium: 20 mm
Max. Application Range - Copper: 10 mm
Max. Application Range - Brass: 12 mm
Cutting area: 3.048 x 1.530 mm
X-axis: 3048 mm
Y-axis: 1530 mm
Z-Axis: 125 mm
Max. Sheet size: 3.048 x 1.524 mm
Max. sheet weight: 127 kg/m²
Max speed x-axes: 90 m/min
Max speed y-axes: 90 m/min
Max. speed simultaneous: 127 m/min
Max. acceleration: 14 m/s²
Positioning accuracy: +/- 0,05 mm
Repeat accuracy: +/- 0,05 mm
Weight: 6600 kg
Manual table / shuttle table: Manual table
Max. thickness - mild steel: 20 mm
Max. thickness - stainless steel: 15 mm
Max. thickness - aluminium: 20 mm
Max. Application Range - Copper: 10 mm
Max. Application Range - Brass: 12 mm
Cutting area: 3.048 x 1.530 mm
X-axis: 3048 mm
Y-axis: 1530 mm
Z-Axis: 125 mm
Max. Sheet size: 3.048 x 1.524 mm
Max. sheet weight: 127 kg/m²
Max speed x-axes: 90 m/min
Max speed y-axes: 90 m/min
Max. speed simultaneous: 127 m/min
Max. acceleration: 14 m/s²
Positioning accuracy: +/- 0,05 mm
Repeat accuracy: +/- 0,05 mm
Weight: 6600 kg
3
Metal working and machine toolsCutting machines and equipmentLaser cutting machines
Laser power: 6 kW
Manual table / shuttle table: Shuttle table
Max. thickness - mild steel: 20 mm
Max. thickness - stainless steel: 15 mm
Max. thickness - aluminium: 20 mm
Max. Application Range - Copper: 10 mm
Max. Application Range - Brass: 12 mm
Cutting area: 3.048 x 1.530 mm
X-axis: 3060 mm
Y-axis: 1530 mm
Z-Axis: 140 mm
Max. Sheet size: 3.048 x 1.524 mm
Max speed x-axes: 90 m/min
Max speed y-axes: 90 m/min
Max. speed simultaneous: 127 m/min
Max. acceleration: 14 m/s²
Positioning accuracy: +/- 0,05 mm
Repeat accuracy: +/- 0,05 mm
Laser power: 6 kW
Manual table / shuttle table: Shuttle table
Max. thickness - mild steel: 20 mm
Max. thickness - stainless steel: 15 mm
Max. thickness - aluminium: 20 mm
Max. Application Range - Copper: 10 mm
Max. Application Range - Brass: 12 mm
Cutting area: 3.048 x 1.530 mm
X-axis: 3060 mm
Y-axis: 1530 mm
Z-Axis: 140 mm
Max. Sheet size: 3.048 x 1.524 mm
Max speed x-axes: 90 m/min
Max speed y-axes: 90 m/min
Max. speed simultaneous: 127 m/min
Max. acceleration: 14 m/s²
Positioning accuracy: +/- 0,05 mm
Repeat accuracy: +/- 0,05 mm
Manual table / shuttle table: Shuttle table
Max. thickness - mild steel: 20 mm
Max. thickness - stainless steel: 15 mm
Max. thickness - aluminium: 20 mm
Max. Application Range - Copper: 10 mm
Max. Application Range - Brass: 12 mm
Cutting area: 3.048 x 1.530 mm
X-axis: 3060 mm
Y-axis: 1530 mm
Z-Axis: 140 mm
Max. Sheet size: 3.048 x 1.524 mm
Max speed x-axes: 90 m/min
Max speed y-axes: 90 m/min
Max. speed simultaneous: 127 m/min
Max. acceleration: 14 m/s²
Positioning accuracy: +/- 0,05 mm
Repeat accuracy: +/- 0,05 mm
9
Metal working and machine toolsSheet metal working machinesSection steel shears
Punching power: 110 ton
Throat depth: 300 mm
Number of stations: 5
Cylinder: 2
Max. diameter at sheet thickness (mild steel): 40x20 (28x28) mm
Stroke: 80 mm
Strokes: 17 1/min
Flat steel: 600x15 (400x20) mm
Blade length: 605 mm
Angle steel: 152x152x13 mm
Round / square steel: 50/50 mm
Notcher: 90x52x13 mm
Motor: 5 kW
Length: 2130 mm
Width: 1200 mm
Height: 2200 mm
Weight: 2500 kg
Punching power: 110 ton
Throat depth: 300 mm
Number of stations: 5
Cylinder: 2
Max. diameter at sheet thickness (mild steel): 40x20 (28x28) mm
Stroke: 80 mm
Strokes: 17 1/min
Flat steel: 600x15 (400x20) mm
Blade length: 605 mm
Angle steel: 152x152x13 mm
Round / square steel: 50/50 mm
Notcher: 90x52x13 mm
Motor: 5 kW
Length: 2130 mm
Width: 1200 mm
Height: 2200 mm
Weight: 2500 kg
Throat depth: 300 mm
Number of stations: 5
Cylinder: 2
Max. diameter at sheet thickness (mild steel): 40x20 (28x28) mm
Stroke: 80 mm
Strokes: 17 1/min
Flat steel: 600x15 (400x20) mm
Blade length: 605 mm
Angle steel: 152x152x13 mm
Round / square steel: 50/50 mm
Notcher: 90x52x13 mm
Motor: 5 kW
Length: 2130 mm
Width: 1200 mm
Height: 2200 mm
Weight: 2500 kg
1
Metal working and machine toolsSawingBelt saws
Saw frame: Pivot frame
Band dimensions: 5200x34x1,1 mm
Band speed continous: 20-100 m/min
Cutting capacity 0° round: 440 mm
Cutting capacity 0° square: 440 mm
Cutting capacity 0° flat: 610x440 mm
Cutting capacity 45°: rund 410 mm, quadrat 410 mm, rechteck 410 x 440 mm
Cutting capacity 60°: rund 320 mm, quadrat 250 mm, rechteck 250 x 440 mm
Cutting capacity - 45°: rund 410 mm, quadrat 410 mm, rechteck 410 x 440 mm
Cutting capacity - 60°: rund 320 mm, quadrat 285 mm, rechteck 285 x 440 mm
Working height: 860 mm
Hydraulic motor: 0.55 kW
Motor: 3 kW
Coolant pump motor: 0.12 kW
Length: 2800 mm
Width: 1210 mm
Height: 1870 mm
Weight: 1540 kg
Saw frame: Pivot frame
Band dimensions: 5200x34x1,1 mm
Band speed continous: 20-100 m/min
Cutting capacity 0° round: 440 mm
Cutting capacity 0° square: 440 mm
Cutting capacity 0° flat: 610x440 mm
Cutting capacity 45°: rund 410 mm, quadrat 410 mm, rechteck 410 x 440 mm
Cutting capacity 60°: rund 320 mm, quadrat 250 mm, rechteck 250 x 440 mm
Cutting capacity - 45°: rund 410 mm, quadrat 410 mm, rechteck 410 x 440 mm
Cutting capacity - 60°: rund 320 mm, quadrat 285 mm, rechteck 285 x 440 mm
Working height: 860 mm
Hydraulic motor: 0.55 kW
Motor: 3 kW
Coolant pump motor: 0.12 kW
Length: 2800 mm
Width: 1210 mm
Height: 1870 mm
Weight: 1540 kg
Band dimensions: 5200x34x1,1 mm
Band speed continous: 20-100 m/min
Cutting capacity 0° round: 440 mm
Cutting capacity 0° square: 440 mm
Cutting capacity 0° flat: 610x440 mm
Cutting capacity 45°: rund 410 mm, quadrat 410 mm, rechteck 410 x 440 mm
Cutting capacity 60°: rund 320 mm, quadrat 250 mm, rechteck 250 x 440 mm
Cutting capacity - 45°: rund 410 mm, quadrat 410 mm, rechteck 410 x 440 mm
Cutting capacity - 60°: rund 320 mm, quadrat 285 mm, rechteck 285 x 440 mm
Working height: 860 mm
Hydraulic motor: 0.55 kW
Motor: 3 kW
Coolant pump motor: 0.12 kW
Length: 2800 mm
Width: 1210 mm
Height: 1870 mm
Weight: 1540 kg
11
Printing machineryOther
Description
Automatic production of display cards, calendar backs, game boards or luxury packaging. in large format : 1062x 765 mm
Equiped :
PPA 290 Pallet feeder or manual feeding
Copilot System with touchscreen
Miss cloth control during the separation process
Viscositycontrol
Active Line Module for energetic recovery of operating power in the line network
Safety standard according to CE directives and specifications
Template for preparing rubber pads (devise for fitting teh rubber pad on its plate outside the machine
Technical Details
Case size min: 300 x 210 x 1 mm
Case size max : 1092 x 735 x 4 mm
Cloth width: 295 - 1092 mm
Cloth height: 205 - 765 mm
Mechanical speed max: 40 cycles/min
PressurePressure needed: 25 Nm3/h, 6 bar
Turn-in width, closed: 10 - 20 mm
Machine is in very good conditon and visible in production.
Price, and more pictures on request
Directly available
Description
Automatic production of display cards, calendar backs, game boards or luxury packaging. in large format : 1062x 765 mm
Equiped :
PPA 290 Pallet feeder or manual feeding
Copilot System with touchscreen
Miss cloth control during the separation process
Viscositycontrol
Active Line Module for energetic recovery of operating power in the line network
Safety standard according to CE directives and specifications
Template for preparing rubber pads (devise for fitting teh rubber pad on its plate outside the machine
Technical Details
Case size min: 300 x 210 x 1 mm
Case size max : 1092 x 735 x 4 mm
Cloth width: 295 - 1092 mm
Cloth height: 205 - 765 mm
Mechanical speed max: 40 cycles/min
PressurePressure needed: 25 Nm3/h, 6 bar
Turn-in width, closed: 10 - 20 mm
Machine is in very good conditon and visible in production.
Price, and more pictures on request
Directly available
Automatic production of display cards, calendar backs, game boards or luxury packaging. in large format : 1062x 765 mm
Equiped :
PPA 290 Pallet feeder or manual feeding
Copilot System with touchscreen
Miss cloth control during the separation process
Viscositycontrol
Active Line Module for energetic recovery of operating power in the line network
Safety standard according to CE directives and specifications
Template for preparing rubber pads (devise for fitting teh rubber pad on its plate outside the machine
Technical Details
Case size min: 300 x 210 x 1 mm
Case size max : 1092 x 735 x 4 mm
Cloth width: 295 - 1092 mm
Cloth height: 205 - 765 mm
Mechanical speed max: 40 cycles/min
PressurePressure needed: 25 Nm3/h, 6 bar
Turn-in width, closed: 10 - 20 mm
Machine is in very good conditon and visible in production.
Price, and more pictures on request
Directly available
8
Metal working and machine toolsDeburring machines
Working width: 650
Sheet thickness range - mild steel: 0,5 - 170 mm
Grinding belt dimensions: 670 x 2200 mm
Suction capacity: 4000 m³/h
Connection for dust collector diam.: 120 mm
Air connection: 6 bar
Noise level: 83 dB
Motor: 22 kW
Length: 2600 mm
Width: 1350 mm
Height: 2100 mm
Weight: 1125 kg
Working width: 650
Sheet thickness range - mild steel: 0,5 - 170 mm
Grinding belt dimensions: 670 x 2200 mm
Suction capacity: 4000 m³/h
Connection for dust collector diam.: 120 mm
Air connection: 6 bar
Noise level: 83 dB
Motor: 22 kW
Length: 2600 mm
Width: 1350 mm
Height: 2100 mm
Weight: 1125 kg
Sheet thickness range - mild steel: 0,5 - 170 mm
Grinding belt dimensions: 670 x 2200 mm
Suction capacity: 4000 m³/h
Connection for dust collector diam.: 120 mm
Air connection: 6 bar
Noise level: 83 dB
Motor: 22 kW
Length: 2600 mm
Width: 1350 mm
Height: 2100 mm
Weight: 1125 kg
1
Metal working and machine toolsSheet metal working machinesPunching
Punching power: 80 ton
Throat depth: 510 mm
Max. diameter at sheet thickness (mild steel): 40x14 mm
Max. number of strokes at 20 mm stroke: 40 1/min
Motor: 9 kW
Length: 1700 mm
Width: 1300 mm
Height: 2050 mm
Weight: 1715 kg
Punching power: 80 ton
Throat depth: 510 mm
Max. diameter at sheet thickness (mild steel): 40x14 mm
Max. number of strokes at 20 mm stroke: 40 1/min
Motor: 9 kW
Length: 1700 mm
Width: 1300 mm
Height: 2050 mm
Weight: 1715 kg
Throat depth: 510 mm
Max. diameter at sheet thickness (mild steel): 40x14 mm
Max. number of strokes at 20 mm stroke: 40 1/min
Motor: 9 kW
Length: 1700 mm
Width: 1300 mm
Height: 2050 mm
Weight: 1715 kg
1
Metal working and machine toolsSheet metal working machinesPunching
Punching power: 55 ton
Throat depth: 750 mm
Max. diameter at sheet thickness (mild steel): 40x14 mm
Max. number of strokes at 20 mm stroke: 37 1/min
Motor: 5 kW
Length: 1930 mm
Width: 1200 mm
Height: 1800 mm
Weight: 1885 kg
Punching power: 55 ton
Throat depth: 750 mm
Max. diameter at sheet thickness (mild steel): 40x14 mm
Max. number of strokes at 20 mm stroke: 37 1/min
Motor: 5 kW
Length: 1930 mm
Width: 1200 mm
Height: 1800 mm
Weight: 1885 kg
Throat depth: 750 mm
Max. diameter at sheet thickness (mild steel): 40x14 mm
Max. number of strokes at 20 mm stroke: 37 1/min
Motor: 5 kW
Length: 1930 mm
Width: 1200 mm
Height: 1800 mm
Weight: 1885 kg
1
Metal working and machine toolsSheet metal working machinesFeed straighteners
Sheet Thickness - mild steel: 0.4 - 2 mm
Max. sheet width: 600 mm
Max. cross-section: 600x2 mm
Feed roll diameter: 80 mm
Feeding speed: 75 m/min
Feeding acceleration: 10 m/s²
Motor torque: 10 Nm
Sheet Thickness - mild steel: 0.4 - 2 mm
Max. sheet width: 600 mm
Max. cross-section: 600x2 mm
Feed roll diameter: 80 mm
Feeding speed: 75 m/min
Feeding acceleration: 10 m/s²
Motor torque: 10 Nm
Max. sheet width: 600 mm
Max. cross-section: 600x2 mm
Feed roll diameter: 80 mm
Feeding speed: 75 m/min
Feeding acceleration: 10 m/s²
Motor torque: 10 Nm
2
Metal working and machine toolsSheet metal working machinesFeed straighteners
Sheet Thickness - mild steel: 0.4 - 3 mm
Max. sheet width: 400 mm
Max. cross-section: 400x3 mm
Feed roll diameter: 80 mm
Feeding speed: 75 m/min
Feeding acceleration: 10 m/s²
Motor torque: 10 Nm
Sheet Thickness - mild steel: 0.4 - 3 mm
Max. sheet width: 400 mm
Max. cross-section: 400x3 mm
Feed roll diameter: 80 mm
Feeding speed: 75 m/min
Feeding acceleration: 10 m/s²
Motor torque: 10 Nm
Max. sheet width: 400 mm
Max. cross-section: 400x3 mm
Feed roll diameter: 80 mm
Feeding speed: 75 m/min
Feeding acceleration: 10 m/s²
Motor torque: 10 Nm
2
Metal working and machine toolsSheet metal working machinesBending machines
Bending length: 350 - 2800 mm
Max. sheet length: 3050 mm
Max. sheet width: 1524 mm
Min. bendable width: 150 mm
Max. bending height: 254 mm
Max. bending depth: 50 mm
Max. sheet rotation area: 3300 mm
Bending force: 500 to
Pressure force: 1000 to
Sheet thickness (420 N/mm²): 3.2 mm
Sheet thickness (600 N/mm²): 2.2 mm
Sheet thickness (260 N/mm²): 4 mm
Min. sheet thickness - mild steel: 0.5 mm
Max. bending angle: 135 °
Bending length: 350 - 2800 mm
Max. sheet length: 3050 mm
Max. sheet width: 1524 mm
Min. bendable width: 150 mm
Max. bending height: 254 mm
Max. bending depth: 50 mm
Max. sheet rotation area: 3300 mm
Bending force: 500 to
Pressure force: 1000 to
Sheet thickness (420 N/mm²): 3.2 mm
Sheet thickness (600 N/mm²): 2.2 mm
Sheet thickness (260 N/mm²): 4 mm
Min. sheet thickness - mild steel: 0.5 mm
Max. bending angle: 135 °
Max. sheet length: 3050 mm
Max. sheet width: 1524 mm
Min. bendable width: 150 mm
Max. bending height: 254 mm
Max. bending depth: 50 mm
Max. sheet rotation area: 3300 mm
Bending force: 500 to
Pressure force: 1000 to
Sheet thickness (420 N/mm²): 3.2 mm
Sheet thickness (600 N/mm²): 2.2 mm
Sheet thickness (260 N/mm²): 4 mm
Min. sheet thickness - mild steel: 0.5 mm
Max. bending angle: 135 °
2
Metal working and machine toolsSheet metal working machines
Suitable for plates: 1
Max. bevel width: 66 mm
Bevel angle: 60 °
Spindle speed (load-free): 300-800 rpm
Feed speed: 0 - 1,2 mm/min
Max. cutting depth: 6 mm
Motor: 6.5 kW
Length: 1179 mm
Width: 853 mm
Height: 1524 mm
Weight: 320 kg
Suitable for plates: 1
Max. bevel width: 66 mm
Bevel angle: 60 °
Spindle speed (load-free): 300-800 rpm
Feed speed: 0 - 1,2 mm/min
Max. cutting depth: 6 mm
Motor: 6.5 kW
Length: 1179 mm
Width: 853 mm
Height: 1524 mm
Weight: 320 kg
Max. bevel width: 66 mm
Bevel angle: 60 °
Spindle speed (load-free): 300-800 rpm
Feed speed: 0 - 1,2 mm/min
Max. cutting depth: 6 mm
Motor: 6.5 kW
Length: 1179 mm
Width: 853 mm
Height: 1524 mm
Weight: 320 kg
2
Metal working and machine toolsSheet metal working machines
Suitable for plates: 1
Suitable for tubes: 1
Max. bevel width: 30 mm
Bevel angle: 60 °
Spindle speed (load-free): 500-2920 rpm
Bevel of tube outer edge: 50 - 150 m/min
Feed speed: 3 mm/min
Work piece height: 100 mm
Motor: 7.5 kW
Length: 1216 mm
Width: 1275 mm
Weight: 850 kg
Suitable for plates: 1
Suitable for tubes: 1
Max. bevel width: 30 mm
Bevel angle: 60 °
Spindle speed (load-free): 500-2920 rpm
Bevel of tube outer edge: 50 - 150 m/min
Feed speed: 3 mm/min
Work piece height: 100 mm
Motor: 7.5 kW
Length: 1216 mm
Width: 1275 mm
Weight: 850 kg
Suitable for tubes: 1
Max. bevel width: 30 mm
Bevel angle: 60 °
Spindle speed (load-free): 500-2920 rpm
Bevel of tube outer edge: 50 - 150 m/min
Feed speed: 3 mm/min
Work piece height: 100 mm
Motor: 7.5 kW
Length: 1216 mm
Width: 1275 mm
Weight: 850 kg
2
Metal working and machine toolsSheet metal working machines
Suitable for plates: 1
Suitable for tubes: 1
Max. bevel width: 21 mm
Bevel angle: 60 °
Spindle speed (load-free): 2740-3290 rpm
Motor: 2.2 kW
Weight: 21 kg
Suitable for plates: 1
Suitable for tubes: 1
Max. bevel width: 21 mm
Bevel angle: 60 °
Spindle speed (load-free): 2740-3290 rpm
Motor: 2.2 kW
Weight: 21 kg
Suitable for tubes: 1
Max. bevel width: 21 mm
Bevel angle: 60 °
Spindle speed (load-free): 2740-3290 rpm
Motor: 2.2 kW
Weight: 21 kg
1
Metal working and machine toolsSheet metal working machines
Suitable for plates: 1
Suitable for tubes: 1
Max. bevel width: 21 mm
Bevel angle: 60 °
Spindle speed (load-free): 2820 rpm
Motor: 1.1 kW
Weight: 20 kg
Suitable for plates: 1
Suitable for tubes: 1
Max. bevel width: 21 mm
Bevel angle: 60 °
Spindle speed (load-free): 2820 rpm
Motor: 1.1 kW
Weight: 20 kg
Suitable for tubes: 1
Max. bevel width: 21 mm
Bevel angle: 60 °
Spindle speed (load-free): 2820 rpm
Motor: 1.1 kW
Weight: 20 kg
1
Metal working and machine toolsSheet metal working machinesPlate shears
Cutting length: 1280 mm
Max. thickness - mild steel: 16 mm
Max. thickness - stainless steel: 12 mm
Strokes: 8 1/min
Cutting angle: 3 °
Number of downholders: 7 pcs.
Back gauge: 500 mm
Motor power: 22.5 kW
Oiltank: 250 l
Table height: 950 mm
Length: 2100 mm
Width: 1400 mm
Height: 2000 mm
Weight: 5000 kg
Cutting length: 1280 mm
Max. thickness - mild steel: 16 mm
Max. thickness - stainless steel: 12 mm
Strokes: 8 1/min
Cutting angle: 3 °
Number of downholders: 7 pcs.
Back gauge: 500 mm
Motor power: 22.5 kW
Oiltank: 250 l
Table height: 950 mm
Length: 2100 mm
Width: 1400 mm
Height: 2000 mm
Weight: 5000 kg
Max. thickness - mild steel: 16 mm
Max. thickness - stainless steel: 12 mm
Strokes: 8 1/min
Cutting angle: 3 °
Number of downholders: 7 pcs.
Back gauge: 500 mm
Motor power: 22.5 kW
Oiltank: 250 l
Table height: 950 mm
Length: 2100 mm
Width: 1400 mm
Height: 2000 mm
Weight: 5000 kg
1
Metal working and machine toolsSheet metal working machinesPlate shears
Cutting length: 1530 mm
Max. thickness - mild steel: 12 mm
Max. thickness - stainless steel: 9 mm
Strokes: 8 1/min
Cutting angle: 3 °
Number of downholders: 8 pcs.
Back gauge: 500 mm
Motor power: 15 kW
Oiltank: 180 l
Table height: 950 mm
Length: 2200 mm
Width: 1200 mm
Height: 1800 mm
Weight: 3400 kg
Cutting length: 1530 mm
Max. thickness - mild steel: 12 mm
Max. thickness - stainless steel: 9 mm
Strokes: 8 1/min
Cutting angle: 3 °
Number of downholders: 8 pcs.
Back gauge: 500 mm
Motor power: 15 kW
Oiltank: 180 l
Table height: 950 mm
Length: 2200 mm
Width: 1200 mm
Height: 1800 mm
Weight: 3400 kg
Max. thickness - mild steel: 12 mm
Max. thickness - stainless steel: 9 mm
Strokes: 8 1/min
Cutting angle: 3 °
Number of downholders: 8 pcs.
Back gauge: 500 mm
Motor power: 15 kW
Oiltank: 180 l
Table height: 950 mm
Length: 2200 mm
Width: 1200 mm
Height: 1800 mm
Weight: 3400 kg