Liverani EP-Midex flexible impeller pump, Serial: 122340, Stainless, flexible impeller pump, 0.75Kw motor, 1400RPM, 3Ph

Liverani EP-Mini 25, flexible impeller pump, Serial: 117246, Stainless, flexible impeller pump, 0.48Kw motor, 1360RPM, 3Ph

Letina PZP1100 Variable capacity tank, Serial: 146720, 2020, Stainless, Variable capacity tank, max capacity 1100L, with floating lid and inflatable gasket achieves an air tight seal

Dalmec PMC Barrel Drum lifter, Serial: 935719, 2009, Dalmec PRC, clamp jaws type, especially designed for picking and emptying drum. Barrels. Containers, one operator, max load 300Kg, with spare clamps and manual

Dalmec PRC Barrel Drum lifter, Serial: 324899, 2003, Dalmec PRC, clamp jaws type, especially designed for picking and emptying drum. Barrels. Containers, one operator, max load 250Kg

Dalmec PRC Barrel Drum lifter, Serial: 9816115, Dalmec PRC, clamp jaws type, especially designed for picking and emptying drum. Barrels. Containers, one operator, max load 300Kg

Adpak Uniblock 712AD Shrinkwrapper and heat tunnel, Automatic shrinkwrapper and heat tunnel, sealing bar 750mm, with hold down, tunnel aperture 600mm x 450mm, mobile, 3Ph

Daikin VRV1V Loop Condensing unit, Daikin VRV 1V Loop condensing unit, outdoor unit VRV air conditioner, R410A,

SSP SR-3-027-LS3A Lobe pump, Stainless lobe pump, 1.1Kw motor, 450mm inlet and outlet pipes, 3Ph

STS DTP04 Drum barrel mover, Drum and barrel mover with side shift, unique over pallet lifter allows you to load and unload an entire pallet of drums from just one side, mobile

STS STP01 Power clamp drum tipper, Power clamp drum tipper can lift and tip drums and barrels from 50L to 220L, the unit is pneumatic-hydraulic powered, 350Kgs SWL, mobile

STS DTP05 Corner drum lifting trolley, Corner drum lifting trolley, 350Kgs SWL, the universal drum catch lets you connect the unit to a wide variety of drums, height adjustable drum gripper, mobile, 2 in stock

AC Hydraulic DT300H Hydraulic drum trolley, Serial: 281280, Hydraulic drum trolley, designed to lift 200l drums, equipped with a gripping device, mobile

Alfa Laval LKH-UP70 Centrifugal pump, Year 2023, Serial: 298034, Stainless centrifugal pump, 22Kw motor, 3Ph

Alfa Laval LKH70 Centrifugal pump, Serial: 83321, Stainless centrifugal pump, 30Kw motor, 3Ph

Alfa Laval LKH70 Centrifugal pump, Serial: 49700, Stainless centrifugal pump, 22Kw motor, 3Ph

Alfa Laval LKH70 Centrifugal pump, Serial: 39398, Stainless centrifugal pump, 30Kw motor, 3Ph

Alfa Laval LKH70 Centrifugal pump, Serial: 39397, Stainless centrifugal pump, 22Kw motor, 3Ph

Alfa Laval LKH70 Centrifugal pump, Serial: 36794, Stainless centrifugal pump, 22Kw motor, 3Ph

Alfa Laval SX2-013 Lobe pump, Serial: 423753, Stainless lobe pump, 40mm inlet and outlet, 0.55Kw motor, 3Ph

Alfa Laval SX2-013H Lobe pump, Serial: 382784, Stainless lobe pump, 40mm inlet and outlet, 0.55Kw motor, 3Ph

Alfa Laval SX2-013 Lobe pump, Serial: 433642, Stainless lobe pump, 50mm inlet and outlet, 0.55Kw motor, 3Ph

Alfa Laval SRU2-018-LS Lobe pump, Serial: 413445, Stainless lobe pump, 45mm inlet and outlet, 1.1Kw motor, 3Ph

Alfa Laval SX4-063H Lobe pump, Serial: 349019, Stainless lobe pump, mounted on stainless frame, variable speed control, 50mm inlet and outlet pipe, 3Kw motor, mobile, 3Ph

Endoline 605 case taper, Top and bottom case taper, side grip belts, max box width 400mm x max box height 450mm, with roller conveyor outfeed, mobile, 3Ph

Endoline 602 case taper, Top case taper, side grip belts, max box width 350mm x max box height 500mm, mobile, 3Ph

Arnott Stainless conveyor, 2019, Stainless, slat band conveyor, belt dimensions 1000mm x 250mm, mobile

Aro Double diaphragm pump, Air operated double diaphragm pumps, mounted on stainless mobile stand

Sandpiper Double diaphragm pump, Air operated double diaphragm pumps, mounted on stainless mobile stand

Aro Double diaphragm pump, Air operated double diaphragm pumps, mounted on stainless stand

Tapflo TX225 STT Double diaphragm pump, The Tapflo sanitary series air operated double diaphram pumps, ideal for food, beverage, pharma and cosmetic industries, mounted on stainless frames, 5 in stock

STS DTP05 Corner drum lifting trolley, Corner drum lifting trolley, 350Kgs SWL, the universal drum catch lets you connect the unit to a wide variety of drums, height adjustable drum gripper, mobile, 5 in stock

Woods 56JM/20/4/6/10-36 flow extract fan, Year 2021, 560mm fan diameter, 1420 rev/min, see plate for spec, 5 in stock, 3Ph

DTB Stainless conveyor, Stainless conveyor, belt dimensions 1500mm x 300mm, stainless side guides, 3Ph

DTB washing conveyor, Stainless, belt dimensions 1200mm x 300mm, with jet spray mounted on top of the conveyor with recirculation tank and pump for washing products, previously used for olives, 3Ph

DTB Bucket elevator washing conveyor Stainless, bucket elevator conveyor, site inside a 500L stainless tank with recirculation pump, previously used for washing olives, elevates to 1800,, belt width 250mm, overall length of system 2700mm, two in stock, 3Ph

Grundfos CHI2-30 A-W-G Pump, 2010, 2900RPM, 2.5M3/H, rated head 19M, 19mm impeller, max operating pressure 10bar, 3Ph (two in stock)

Hache 1720E Turbidimeter, Hach 1720E Continuous-reading Nephelometric Low Range Process Turbidimeter, Continuously flowing sample flows through the patented bubble removal system, which vents entrained air from the sample stream and eliminates the most significant interference in low level turbidity measurement. The 1720E Turbidimeter is not affected by variations in flow and pressure, The 1720E Turbidimeter uses the sc200 Controller to receive data from up to two sensors. A built-in data logger collects turbidity measurement at user selectable intervals (1-15 minutes), along with calibration and verification points, alarm history, and instrument setup changes for 6 months.

Europ-Plast VCPA315 centrifugal extraction fan, Serial: V9064, 2010, chemical resistant centrifugal extraction fan, 5.5Kw, all fans are manufacturered as direct drive assemblies and all casings are fully welded and come standard with chemical resistant vapor seals

Longwood D screen Fine screen, 2010, Dscreen simple design, operation and maintenance make it the ideal choice for reliable stand alone water filtration, fully enclosed unit, self cleaning screen, 0.8mm screens, Length 1200mm, width 1023mm, 0.37Kw motor, two available

Longwood Rotapak150 Screw compactor, 2010, screw compactor, screenings handling equipment, screw diameter 150mm, capacity 0.5M3/hr, 1.5Kw motor, 3Ph

Lowara 10HM02P11T5RVBE Multistage pump, Serial: 20170110, 2010, Horizontal multistage pump, mounted on stainless frame with Xylem flow meter, 1.23Kw, see plate for full spec

Sigma S2CAHM07120PVT Metering pump, Serial: 2010132518, 2010, 0.25Kw, Metering pumps, 3 in stock

Hoval Air receiver tank, 2010, capacity 500L, working temp -10'C to 45'C, max working pressure 10Bar,

AVK Flanged gate valve, 2010, flanged gate valves with handwheels, 10+ in stock, various sizes

Punching power: 110 ton
Throat depth: 610 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 420/20 bzw. 28/28 mm
Stroke: 80 mm
Strokes: 28 1/min
Flat steel: 600x15 / 400x20 mm
Angle steel: 152x152x13 mm
Round / square steel: 50 mm
Notcher: 13x52x90 mm
Motor: 9 kW
Length: 2690 mm
Width: 1400 mm
Height: 2200 mm
Weight: 3300 kg

Bending length: 1550 mm
Max. bending capacity - mild steel: 9
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 9 mm
Max. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 7 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 7 mm
Max. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 5 mm
Upper roll diameter: 180 mm
Lower roll diameter: 180 mm
Lateral roll diameter: 150 mm
Bending speed: 1,5 / 6 m/min
Motor power: 5 kW
Length: 3900 mm
Width: 1150 mm
Height: 1250 mm
Weight: 3250 kg

Bending length: 4010 mm
Bending capacity steel 400 N/mm²: 1.25 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.25 mm
No. of stand and tension arm units: 4
No. of driven linkage assemblies: 4
Sheet insertion depth: 1000 mm
Opening of upper beam: 190 mm
Working height: 835 mm
Motor: 2.2 kW
Length with electrical shear: 5200 mm
Width: 1300 mm
Height: 1900 mm
Weight: 1550 kg

Renz Super 700 Wiro Punching Machine – Heavy-Duty Punching for Wire Binding

The Renz Super 700 is a robust, high-capacity punching machine designed for demanding production environments. Built for precision and durability, this semi-automatic wire punching system is ideal for professional print shops, bookbinding operations, and finishing departments.

Key Features:

Heavy-duty construction – Built to handle high-volume workloads with ease.

Interchangeable punching dies – Quickly switch between different punch patterns for maximum flexibility.

Punching width up to 700 mm – Suitable for a wide range of formats, including oversized documents.

Foot pedal operation – For hands-free control and improved workflow efficiency.
Clean and precise punching – Delivers consistent results across paper, cardboard, and plastic sheets.
Whether you're producing calendars, notebooks, or presentation materials, the Renz Super 700 offers speed, reliability, and excellent punching quality for wire binding applications.

Condition: Used, in excellent working condition
Available immediately – Contact us for pricing, shipping options, or to schedule a demo

Saw frame: Pivot frame
Band dimensions: 4160x34x1,1 mm
Band speed continous: 15 - 120 m/min
Cutting capacity 0° round: 320 mm
Cutting capacity 0° square: 320 mm
Cutting capacity 0° flat: 450x320 mm
Cutting capacity 30°: round 320 mm, square 320 mm, rectangular 380x320 mm
Cutting capacity 45°: round 320 mm, square 320 mm, rectangular 330x320 mm
Cutting capacity - 30°: round 320 mm, square 320 mm, rectangular 380x320 mm
Cutting capacity - 45°: round 320 mm, square 300 mm, rectangular 340x320 mm
Cutting capacity - 60°: round 230 mm, square 220 mm, rectangular 230x220 mm
Working height: 860 mm
Hydraulic motor: 0.37 kW
Motor: 2.2 kW
Coolant pump motor: 0.12 kW
Length: 2230 mm
Width: 1150 mm
Height: 2140 mm
Weight: 1030 kg