11
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18617
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Ref. no.: 18617
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
13
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18616
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Ref. no.: 18616
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
13
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18615
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Ref. no.: 18615
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
8
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18614
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 18 mm
Injection volume: 26 cm³
Shot weight: 23 g
Injection pressure: 2800 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Ref. no.: 18614
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 18 mm
Injection volume: 26 cm³
Shot weight: 23 g
Injection pressure: 2800 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 18 mm
Injection volume: 26 cm³
Shot weight: 23 g
Injection pressure: 2800 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
13
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18613
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 74 cm³
Shot weight: 60 g
Injection pressure: 1390 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Ref. no.: 18613
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 74 cm³
Shot weight: 60 g
Injection pressure: 1390 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 74 cm³
Shot weight: 60 g
Injection pressure: 1390 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
13
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18612
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 22 mm
Injection volume: 39 cm³
Shot weight: 35 g
Injection pressure: 2500 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Ref. no.: 18612
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 22 mm
Injection volume: 39 cm³
Shot weight: 35 g
Injection pressure: 2500 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 22 mm
Injection volume: 39 cm³
Shot weight: 35 g
Injection pressure: 2500 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
13
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18138
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 850 mm
Distance between tie bars: 370 X 370 mm
Mould height min.: 200 mm
Mould height max.: 510 mm
Platen size (h x v): 600 x 600 mm
Injection unit
Screw diameter: 22 mm
Injection volume: 37 cm³
Shot weight: 32 g
Injection pressure: 2580 bar
Measurements and weight
Dimensions: 4,50 X 1,28 X 1,95 m
Machine weight: 4750 kg
Ref. no.: 18138
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 850 mm
Distance between tie bars: 370 X 370 mm
Mould height min.: 200 mm
Mould height max.: 510 mm
Platen size (h x v): 600 x 600 mm
Injection unit
Screw diameter: 22 mm
Injection volume: 37 cm³
Shot weight: 32 g
Injection pressure: 2580 bar
Measurements and weight
Dimensions: 4,50 X 1,28 X 1,95 m
Machine weight: 4750 kg
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 850 mm
Distance between tie bars: 370 X 370 mm
Mould height min.: 200 mm
Mould height max.: 510 mm
Platen size (h x v): 600 x 600 mm
Injection unit
Screw diameter: 22 mm
Injection volume: 37 cm³
Shot weight: 32 g
Injection pressure: 2580 bar
Measurements and weight
Dimensions: 4,50 X 1,28 X 1,95 m
Machine weight: 4750 kg
13
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18622
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 115 cm³
Shot weight: 103 g
Injection pressure: 1600 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Additional information & extras
Core pull: 1 pcs
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Ref. no.: 18622
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 115 cm³
Shot weight: 103 g
Injection pressure: 1600 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Additional information & extras
Core pull: 1 pcs
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 115 cm³
Shot weight: 103 g
Injection pressure: 1600 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Additional information & extras
Core pull: 1 pcs
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
12
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18621
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 115 cm³
Shot weight: 103 g
Injection pressure: 1600 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Ref. no.: 18621
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 115 cm³
Shot weight: 103 g
Injection pressure: 1600 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 115 cm³
Shot weight: 103 g
Injection pressure: 1600 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
10
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18620
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 85 cm³
Shot weight: 76 g
Injection pressure: 2180 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Additional information & extras
Core pull: 1 pcs
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Ref. no.: 18620
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 85 cm³
Shot weight: 76 g
Injection pressure: 2180 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Additional information & extras
Core pull: 1 pcs
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 85 cm³
Shot weight: 76 g
Injection pressure: 2180 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Additional information & extras
Core pull: 1 pcs
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
9
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18619
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 85 cm³
Shot weight: 76 g
Injection pressure: 2180 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Further information:
Die Sumitomo (SHI) Demag IntElect Serie gehört zu den hochpräzisen vollelektrischen Spritzgießmaschinen, die speziell für technische Kunststoffteile, Automobilanwendungen, elektronische Komponenten sowie anspruchsvolle Serienproduktionen entwickelt wurden.
Alle Hauptbewegungen der Maschine werden über Direct-Drive Servo-Elektromotoren angetrieben. Einspritzen, Dosieren, Werkzeugbewegungen sowie Auswerferfunktionen erfolgen vollständig elektrisch und ermöglichen dadurch höchste Präzision, ausgezeichnete Wiederholgenauigkeit und maximale Prozessstabilität.
Die IntElect Serie ist besonders bekannt für ihren niedrigen Energieverbrauch und ihre hohe Produktionspräzision. Im Vergleich zu konventionellen hydraulischen Spritzgießmaschinen können – abhängig von der Anwendung – Energieeinsparungen von ca. 60 % bis zu 80 % erzielt werden. Gleichzeitig reduziert die geringe Wärmeentwicklung den Kühlbedarf und senkt die gesamten Betriebskosten.
Die Maschine verfügt über ein direktes Servo-Einspritz- und Dosiersystem, das sehr schnelle Reaktionszeiten und eine hochpräzise Einspritzsteuerung ermöglicht. Die Spritzeinheit ist mit 4 Heizzonen ausgestattet und sorgt dadurch für eine homogene Plastifizierung sowie stabile Prozessbedingungen, insbesondere bei technischen Kunststoffen.
Die wichtigsten Vorteile der IntElect Serie:
* Vollelektrische Direct-Drive Servo-Technologie
* Sehr geringer Energieverbrauch
* Hohe Präzision und Prozesswiederholgenauigkeit
* Geräuscharmer und vibrationsarmer Betrieb
* Hohe dynamische Servo-Performance
* Geringer Wartungsaufwand
* Saubere Produktionsumgebung
* Ideale Lösung für technische und Präzisionsteile
* Geeignet für schnelle Serienproduktionen
Die Sumitomo Demag IntElect Serie zählt aufgrund ihrer langen Lebensdauer, stabilen Produktionsleistung und hohen Energieeffizienz auch heute noch zu den gefragtesten vollelektrischen Spritzgießmaschinen am Markt.
Ref. no.: 18619
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 85 cm³
Shot weight: 76 g
Injection pressure: 2180 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Further information:
Die Sumitomo (SHI) Demag IntElect Serie gehört zu den hochpräzisen vollelektrischen Spritzgießmaschinen, die speziell für technische Kunststoffteile, Automobilanwendungen, elektronische Komponenten sowie anspruchsvolle Serienproduktionen entwickelt wurden.
Alle Hauptbewegungen der Maschine werden über Direct-Drive Servo-Elektromotoren angetrieben. Einspritzen, Dosieren, Werkzeugbewegungen sowie Auswerferfunktionen erfolgen vollständig elektrisch und ermöglichen dadurch höchste Präzision, ausgezeichnete Wiederholgenauigkeit und maximale Prozessstabilität.
Die IntElect Serie ist besonders bekannt für ihren niedrigen Energieverbrauch und ihre hohe Produktionspräzision. Im Vergleich zu konventionellen hydraulischen Spritzgießmaschinen können – abhängig von der Anwendung – Energieeinsparungen von ca. 60 % bis zu 80 % erzielt werden. Gleichzeitig reduziert die geringe Wärmeentwicklung den Kühlbedarf und senkt die gesamten Betriebskosten.
Die Maschine verfügt über ein direktes Servo-Einspritz- und Dosiersystem, das sehr schnelle Reaktionszeiten und eine hochpräzise Einspritzsteuerung ermöglicht. Die Spritzeinheit ist mit 4 Heizzonen ausgestattet und sorgt dadurch für eine homogene Plastifizierung sowie stabile Prozessbedingungen, insbesondere bei technischen Kunststoffen.
Die wichtigsten Vorteile der IntElect Serie:
* Vollelektrische Direct-Drive Servo-Technologie
* Sehr geringer Energieverbrauch
* Hohe Präzision und Prozesswiederholgenauigkeit
* Geräuscharmer und vibrationsarmer Betrieb
* Hohe dynamische Servo-Performance
* Geringer Wartungsaufwand
* Saubere Produktionsumgebung
* Ideale Lösung für technische und Präzisionsteile
* Geeignet für schnelle Serienproduktionen
Die Sumitomo Demag IntElect Serie zählt aufgrund ihrer langen Lebensdauer, stabilen Produktionsleistung und hohen Energieeffizienz auch heute noch zu den gefragtesten vollelektrischen Spritzgießmaschinen am Markt.
Manufacturer: DEMAG
Year of construction: 2008
Clamping unit
Clamping force: 100 ton
Opening stroke: 380 mm
Distance between tie bars: 470 x 420 mm
Mould height min.: 200 mm
Mould height max.: 430 mm
Platen size (h x v): 690 x 620 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 85 cm³
Shot weight: 76 g
Injection pressure: 2180 bar
Measurements and weight
Dimensions: 4,8 x 1,4 x 2,2 m
Machine weight: 5500 kg
Further information:
Die Sumitomo (SHI) Demag IntElect Serie gehört zu den hochpräzisen vollelektrischen Spritzgießmaschinen, die speziell für technische Kunststoffteile, Automobilanwendungen, elektronische Komponenten sowie anspruchsvolle Serienproduktionen entwickelt wurden.
Alle Hauptbewegungen der Maschine werden über Direct-Drive Servo-Elektromotoren angetrieben. Einspritzen, Dosieren, Werkzeugbewegungen sowie Auswerferfunktionen erfolgen vollständig elektrisch und ermöglichen dadurch höchste Präzision, ausgezeichnete Wiederholgenauigkeit und maximale Prozessstabilität.
Die IntElect Serie ist besonders bekannt für ihren niedrigen Energieverbrauch und ihre hohe Produktionspräzision. Im Vergleich zu konventionellen hydraulischen Spritzgießmaschinen können – abhängig von der Anwendung – Energieeinsparungen von ca. 60 % bis zu 80 % erzielt werden. Gleichzeitig reduziert die geringe Wärmeentwicklung den Kühlbedarf und senkt die gesamten Betriebskosten.
Die Maschine verfügt über ein direktes Servo-Einspritz- und Dosiersystem, das sehr schnelle Reaktionszeiten und eine hochpräzise Einspritzsteuerung ermöglicht. Die Spritzeinheit ist mit 4 Heizzonen ausgestattet und sorgt dadurch für eine homogene Plastifizierung sowie stabile Prozessbedingungen, insbesondere bei technischen Kunststoffen.
Die wichtigsten Vorteile der IntElect Serie:
* Vollelektrische Direct-Drive Servo-Technologie
* Sehr geringer Energieverbrauch
* Hohe Präzision und Prozesswiederholgenauigkeit
* Geräuscharmer und vibrationsarmer Betrieb
* Hohe dynamische Servo-Performance
* Geringer Wartungsaufwand
* Saubere Produktionsumgebung
* Ideale Lösung für technische und Präzisionsteile
* Geeignet für schnelle Serienproduktionen
Die Sumitomo Demag IntElect Serie zählt aufgrund ihrer langen Lebensdauer, stabilen Produktionsleistung und hohen Energieeffizienz auch heute noch zu den gefragtesten vollelektrischen Spritzgießmaschinen am Markt.
9
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18610
Manufacturer: DEMAG
Year of construction: 2012
Clamping unit
Clamping force: 160 ton
Opening stroke: 495 mm
Distance between tie bars: 520 x 520 mm
Mould height min.: 275 mm
Mould height max.: 585 mm
Platen size (h x v): 760 x 785 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 156 cm³
Shot weight: 139 g
Injection pressure: 2180 bar
Measurements and weight
Dimensions: 5,4 x 1,5 x 2,1 m
Machine weight: 7600 kg
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Ref. no.: 18610
Manufacturer: DEMAG
Year of construction: 2012
Clamping unit
Clamping force: 160 ton
Opening stroke: 495 mm
Distance between tie bars: 520 x 520 mm
Mould height min.: 275 mm
Mould height max.: 585 mm
Platen size (h x v): 760 x 785 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 156 cm³
Shot weight: 139 g
Injection pressure: 2180 bar
Measurements and weight
Dimensions: 5,4 x 1,5 x 2,1 m
Machine weight: 7600 kg
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
Manufacturer: DEMAG
Year of construction: 2012
Clamping unit
Clamping force: 160 ton
Opening stroke: 495 mm
Distance between tie bars: 520 x 520 mm
Mould height min.: 275 mm
Mould height max.: 585 mm
Platen size (h x v): 760 x 785 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 156 cm³
Shot weight: 139 g
Injection pressure: 2180 bar
Measurements and weight
Dimensions: 5,4 x 1,5 x 2,1 m
Machine weight: 7600 kg
Further information:
The Sumitomo (SHI) Demag IntElect series is a high-precision all-electric injection moulding machine platform developed for technical plastic parts, automotive applications, electronic components, and demanding serial production processes.
All main machine movements are driven by direct-drive servo electric motors. Injection, dosing, clamping, and ejector movements are performed entirely by electric drive technology, ensuring extremely precise motion control, excellent repeatability, and maximum process stability.
The IntElect series is especially recognized for its low energy consumption and outstanding production precision. Compared to conventional hydraulic injection moulding machines, energy savings of approximately 60% up to 80% can be achieved depending on the application. In addition, the reduced heat generation lowers cooling requirements and overall operating costs.
The machine is equipped with a direct servo injection and dosing system, allowing very fast response times and highly accurate injection control. The injection unit features 4 heating zones, providing homogeneous plasticizing performance and stable processing conditions, especially for technical engineering materials.
Key advantages of the IntElect series:
* All-electric direct-drive servo technology
* Extremely low energy consumption
* High precision and process repeatability
* Quiet and low-vibration operation
* High dynamic servo performance
* Low maintenance requirements
* Clean production environment
* Ideal solution for technical and precision plastic parts
* Suitable for high-speed serial production
The Sumitomo Demag IntElect series is still considered one of the most reliable and efficient all-electric injection moulding machine platforms on the market thanks to its long service life, stable production performance, and excellent energy efficiency.
The machine was in active production until dismantling and is in working condition. As visible in the pictures, the machine is clean and well maintained.
3
Metal working and machine toolsAccessories and spare parts
Lagernummer: 1077-Z01255Maschinenart: ErsatzteileFabrikat: DemagTyp: DIIBaujahr: unbekanntSteuerung: konventionellLagerort: DorstenUrsprungsland: -Lieferzeit: sofortFrachtbasis: ab StandortPreis: Auf Anfrage
Lagernummer: 1077-Z01255
Maschinenart: Ersatzteile
Fabrikat: Demag
Typ: DII
Baujahr: unbekannt
Steuerung: konventionell
Lagerort: Dorsten
Ursprungsland: -
Lieferzeit: sofort
Frachtbasis: ab Standort
Preis: Auf Anfrage
Maschinenart: Ersatzteile
Fabrikat: Demag
Typ: DII
Baujahr: unbekannt
Steuerung: konventionell
Lagerort: Dorsten
Ursprungsland: -
Lieferzeit: sofort
Frachtbasis: ab Standort
Preis: Auf Anfrage
3
Metal working and machine toolsAccessories and spare parts
Lagernummer: 1077-Z01254Maschinenart: ErsatzteileFabrikat: DemagTyp: LRIBaujahr: unbekanntSteuerung: konventionellLagerort: DorstenUrsprungsland: -Lieferzeit: sofortFrachtbasis: ab StandortPreis: Auf Anfrage
Lagernummer: 1077-Z01254
Maschinenart: Ersatzteile
Fabrikat: Demag
Typ: LRI
Baujahr: unbekannt
Steuerung: konventionell
Lagerort: Dorsten
Ursprungsland: -
Lieferzeit: sofort
Frachtbasis: ab Standort
Preis: Auf Anfrage
Maschinenart: Ersatzteile
Fabrikat: Demag
Typ: LRI
Baujahr: unbekannt
Steuerung: konventionell
Lagerort: Dorsten
Ursprungsland: -
Lieferzeit: sofort
Frachtbasis: ab Standort
Preis: Auf Anfrage
9
Metal working and machine toolsOther
LNS QUICK LOAD SERVO 2 / Stangenlademagazin<br /><br />-Stangendurchmesser(rund) 6 - 80mm<br />-Stangenlänge 1,3 - 1,5 Meter<br />-Stangengewicht max. 67 Kg<br />-Ladezeit 4 - 12 Sekunden<br />-Vorschubgeschwindigkeit Max 100m/min<br />-Luftanschluss 5 bar<br /><br />Abmaße: LxBxH 2,2x1,5x1,5 Meter / Gewicht 650Kg
LNS QUICK LOAD SERVO 2 / Stangenlademagazin<br /><br />-Stangendurchmesser(rund) 6 - 80mm<br />-Stangenlänge 1,3 - 1,5 Meter<br />-Stangengewicht max. 67 Kg<br />-Ladezeit 4 - 12 Sekunden<br />-Vorschubgeschwindigkeit Max 100m/min<br />-Luftanschluss 5 bar<br /><br />Abmaße: LxBxH 2,2x1,5x1,5 Meter / Gewicht 650Kg
9
Metal working and machine toolsLathesCNC lathes
TRAUB TNS 65 D / 5 - Achs CNC Drehmaschine-Komplette Technische Daten siehe Datenblätter-Steuerung TX8 D-Baujahr 1994-Stangendurchlass 65 mm-Hydraulisches Stangenlademagazin-Diverse angetriebene Werkzeughalter-Werkzeughalter-Dreibackenfutter-Komplette DokumentationHebkn Auovug Uls S Tel
TRAUB TNS 65 D / 5 - Achs CNC Drehmaschine
-Komplette Technische Daten siehe Datenblätter
-Steuerung TX8 D
-Baujahr 1994
-Stangendurchlass 65 mm
-Hydraulisches Stangenlademagazin
-Diverse angetriebene Werkzeughalter
-Werkzeughalter
-Dreibackenfutter
-Komplette Dokumentation
Hebkn Auovug Uls S Tel
-Komplette Technische Daten siehe Datenblätter
-Steuerung TX8 D
-Baujahr 1994
-Stangendurchlass 65 mm
-Hydraulisches Stangenlademagazin
-Diverse angetriebene Werkzeughalter
-Werkzeughalter
-Dreibackenfutter
-Komplette Dokumentation
Hebkn Auovug Uls S Tel
10
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18565
Manufacturer: DEMAG
Year of construction: 2005
Clamping unit
Clamping force: 150 ton
Opening stroke: 500 mm
Distance between tie bars: 500 x 500 mm
Mould height min.: 250 mm
Opening width: 750 mm
Platen size (h x v): 750 x 750 mm
Injection unit
Screw diameter: 45 mm
Injection volume: 323 cm³
Shot weight: 290 g
Injection pressure: 1973 bar
Measurements and weight
Dimensions: 5.45 x 1.63 x 2.1 m
Machine weight: 7500 kg
Robot
Producer: Wittmann
Type: W721-0231
Year: 2005
Further information:
The Demag Ergotech System series hydraulic injection moulding machine is a suitable plastic injection moulding machine for technical plastic parts and automated serial production applications. Thanks to its hydraulic operating principle, the machine offers powerful and stable injection performance, while the Demag NC4 control system ensures precise process control.
The machine is equipped with a Demag (Wittmann) DR721 linear robot.
Robot specifications:
Year of manufacture: 2005
X-axis: 550 mm
Y-axis: 1000 mm
Z-axis: 2000 mm
The robot system enables fully automatic part removal, conveyor transfer, and automated serial production processes.
In addition, the machine comes with 2 complete spare plasticizing units / injection units (screw and barrel assemblies).
The machine was in running production and operating without problems until dismantling.
Ref. no.: 18565
Manufacturer: DEMAG
Year of construction: 2005
Clamping unit
Clamping force: 150 ton
Opening stroke: 500 mm
Distance between tie bars: 500 x 500 mm
Mould height min.: 250 mm
Opening width: 750 mm
Platen size (h x v): 750 x 750 mm
Injection unit
Screw diameter: 45 mm
Injection volume: 323 cm³
Shot weight: 290 g
Injection pressure: 1973 bar
Measurements and weight
Dimensions: 5.45 x 1.63 x 2.1 m
Machine weight: 7500 kg
Robot
Producer: Wittmann
Type: W721-0231
Year: 2005
Further information:
The Demag Ergotech System series hydraulic injection moulding machine is a suitable plastic injection moulding machine for technical plastic parts and automated serial production applications. Thanks to its hydraulic operating principle, the machine offers powerful and stable injection performance, while the Demag NC4 control system ensures precise process control.
The machine is equipped with a Demag (Wittmann) DR721 linear robot.
Robot specifications:
Year of manufacture: 2005
X-axis: 550 mm
Y-axis: 1000 mm
Z-axis: 2000 mm
The robot system enables fully automatic part removal, conveyor transfer, and automated serial production processes.
In addition, the machine comes with 2 complete spare plasticizing units / injection units (screw and barrel assemblies).
The machine was in running production and operating without problems until dismantling.
Manufacturer: DEMAG
Year of construction: 2005
Clamping unit
Clamping force: 150 ton
Opening stroke: 500 mm
Distance between tie bars: 500 x 500 mm
Mould height min.: 250 mm
Opening width: 750 mm
Platen size (h x v): 750 x 750 mm
Injection unit
Screw diameter: 45 mm
Injection volume: 323 cm³
Shot weight: 290 g
Injection pressure: 1973 bar
Measurements and weight
Dimensions: 5.45 x 1.63 x 2.1 m
Machine weight: 7500 kg
Robot
Producer: Wittmann
Type: W721-0231
Year: 2005
Further information:
The Demag Ergotech System series hydraulic injection moulding machine is a suitable plastic injection moulding machine for technical plastic parts and automated serial production applications. Thanks to its hydraulic operating principle, the machine offers powerful and stable injection performance, while the Demag NC4 control system ensures precise process control.
The machine is equipped with a Demag (Wittmann) DR721 linear robot.
Robot specifications:
Year of manufacture: 2005
X-axis: 550 mm
Y-axis: 1000 mm
Z-axis: 2000 mm
The robot system enables fully automatic part removal, conveyor transfer, and automated serial production processes.
In addition, the machine comes with 2 complete spare plasticizing units / injection units (screw and barrel assemblies).
The machine was in running production and operating without problems until dismantling.
4
Ausladung: 6000 mmTragkraft in kg: kgSchwenkbereich: GradHöhe: 3800 mmGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Ausladung: 6000 mm
Tragkraft in kg: kg
Schwenkbereich: Grad
Höhe: 3800 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Tragkraft in kg: kg
Schwenkbereich: Grad
Höhe: 3800 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
4
Ausladung: 5500 mmTragkraft in kg: 250 kgSchwenkbereich: GradHöhe: 3800 mmGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Ausladung: 5500 mm
Tragkraft in kg: 250 kg
Schwenkbereich: Grad
Höhe: 3800 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Tragkraft in kg: 250 kg
Schwenkbereich: Grad
Höhe: 3800 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
5
Ausladung: 5000 mmTragkraft in kg: 500 kgSchwenkbereich: GradHöhe: 3800 mmGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Ausladung: 5000 mm
Tragkraft in kg: 500 kg
Schwenkbereich: Grad
Höhe: 3800 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Tragkraft in kg: 500 kg
Schwenkbereich: Grad
Höhe: 3800 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
6
Ausladung: 3000 mmTragkraft in kg: 250 kgSchwenkbereich: GradHöhe: 3800 mmGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Ausladung: 3000 mm
Tragkraft in kg: 250 kg
Schwenkbereich: Grad
Höhe: 3800 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Tragkraft in kg: 250 kg
Schwenkbereich: Grad
Höhe: 3800 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Conveyor technologyCranes
Throat: 8000 mm
Total column height: 4000 mm
Load capacity in kg: 3000 kg
Height: 4300mm
Total power requirement: kW
Machine weight approx.: t
Space requirement approx.: m
Throat: 8000 mm
Total column height: 4000 mm
Load capacity in kg: 3000 kg
Height: 4300mm
Total power requirement: kW
Machine weight approx.: t
Space requirement approx.: m
Total column height: 4000 mm
Load capacity in kg: 3000 kg
Height: 4300mm
Total power requirement: kW
Machine weight approx.: t
Space requirement approx.: m
7
Metal working and machine toolsAccessories and spare partsBar stock carriers
Bar length: 3000
Total power: 1 kW
Weight of machine: 800 kg
Space requirement (W x D x H): 4,7 x 0,5 x 1,3 m
Guide tubes 10 and 25 mm, was attached to an EMCO lathe ET242
Accessory: Documentation
Bar length: 3000
Total power: 1 kW
Weight of machine: 800 kg
Space requirement (W x D x H): 4,7 x 0,5 x 1,3 m
Guide tubes 10 and 25 mm, was attached to an EMCO lathe ET242
Accessory: Documentation
Total power: 1 kW
Weight of machine: 800 kg
Space requirement (W x D x H): 4,7 x 0,5 x 1,3 m
Guide tubes 10 and 25 mm, was attached to an EMCO lathe ET242
Accessory: Documentation
11
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18142
Manufacturer: DEMAG
Year of construction: 1997
Clamping unit
Clamping force: 50 ton
Opening stroke: 400 mm
Distance between tie bars: 355 x 355 mm
Mould height min.: 210 mm
Platen size (h x v): 540 x 540 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 106 cm³
Shot weight: 95 g
Injection pressure: 2573 bar
Measurements and weight
Dimensions: 3,65 x 1,15 x 1,18 m
Machine weight: 3600-2500 kg
Ref. no.: 18142
Manufacturer: DEMAG
Year of construction: 1997
Clamping unit
Clamping force: 50 ton
Opening stroke: 400 mm
Distance between tie bars: 355 x 355 mm
Mould height min.: 210 mm
Platen size (h x v): 540 x 540 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 106 cm³
Shot weight: 95 g
Injection pressure: 2573 bar
Measurements and weight
Dimensions: 3,65 x 1,15 x 1,18 m
Machine weight: 3600-2500 kg
Manufacturer: DEMAG
Year of construction: 1997
Clamping unit
Clamping force: 50 ton
Opening stroke: 400 mm
Distance between tie bars: 355 x 355 mm
Mould height min.: 210 mm
Platen size (h x v): 540 x 540 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 106 cm³
Shot weight: 95 g
Injection pressure: 2573 bar
Measurements and weight
Dimensions: 3,65 x 1,15 x 1,18 m
Machine weight: 3600-2500 kg
11
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 17507
Manufacturer: DEMAG
Year of construction: 1998
Clamping unit
Clamping force: 80 ton
Opening stroke: 450 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 200 mm
Platen size (h x v): 600 x 600 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 168 cm³
Shot weight: 149 g
Injection pressure: 2020 bar
Measurements and weight
Dimensions: 4,1 x 1,4 x 2,0 m
Machine weight: 3700 kg
Ref. no.: 17507
Manufacturer: DEMAG
Year of construction: 1998
Clamping unit
Clamping force: 80 ton
Opening stroke: 450 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 200 mm
Platen size (h x v): 600 x 600 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 168 cm³
Shot weight: 149 g
Injection pressure: 2020 bar
Measurements and weight
Dimensions: 4,1 x 1,4 x 2,0 m
Machine weight: 3700 kg
Manufacturer: DEMAG
Year of construction: 1998
Clamping unit
Clamping force: 80 ton
Opening stroke: 450 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 200 mm
Platen size (h x v): 600 x 600 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 168 cm³
Shot weight: 149 g
Injection pressure: 2020 bar
Measurements and weight
Dimensions: 4,1 x 1,4 x 2,0 m
Machine weight: 3700 kg
6
Ausladung: 3000 mmTragkraft in kg: 500 kgSchwenkbereich: . GradGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Ausladung: 3000 mm
Tragkraft in kg: 500 kg
Schwenkbereich: . Grad
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Tragkraft in kg: 500 kg
Schwenkbereich: . Grad
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
4
Tragkraft: 2 tHub: . mmSpannweite: 5600 mmGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Tragkraft: 2 t
Hub: . mm
Spannweite: 5600 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Hub: . mm
Spannweite: 5600 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m