Suitable for plates: 1
Max. bevel width: 66 mm
Bevel angle: 60 °
Spindle speed (load-free): 300-800 rpm
Feed speed: 0 - 1,2 mm/min
Max. cutting depth: 6 mm
Motor: 6.5 kW
Length: 1179 mm
Width: 853 mm
Height: 1524 mm
Weight: 320 kg

Suitable for plates: 1
Suitable for tubes: 1
Max. bevel width: 30 mm
Bevel angle: 60 °
Spindle speed (load-free): 500-2920 rpm
Bevel of tube outer edge: 50 - 150 m/min
Feed speed: 3 mm/min
Work piece height: 100 mm
Motor: 7.5 kW
Length: 1216 mm
Width: 1275 mm
Weight: 850 kg

Suitable for plates: 1
Suitable for tubes: 1
Max. bevel width: 21 mm
Bevel angle: 60 °
Spindle speed (load-free): 2740-3290 rpm
Motor: 2.2 kW
Weight: 21 kg

Suitable for plates: 1
Suitable for tubes: 1
Max. bevel width: 21 mm
Bevel angle: 60 °
Spindle speed (load-free): 2820 rpm
Motor: 1.1 kW
Weight: 20 kg

Suitable for plates: 1
Suitable for tubes: 1
Max. bevel width: 18 mm
Bevel angle: 60 °
Bevel radius: 2-5 mm
Spindle speed (load-free): 1800-5850 rpm
Min. diameter of bevel: 40 mm
Motor: 2.2 kW
Length: 585 mm
Width: 156 mm
Height: 238 mm
Weight: 10 kg

Cutting length: 1530 mm
Max. thickness - mild steel: 16 mm
Max. thickness - stainless steel: 12 mm
Strokes: 7 1/min
Cutting angle: 3 °
Number of downholders: 8 pcs.
Back gauge: 500 mm
Motor power: 22.5 kW
Oiltank: 250 l
Table height: 950 mm
Length: 2350 mm
Width: 1400 mm
Height: 2000 mm
Weight: 5200 kg

Cutting length: 1280 mm
Max. thickness - mild steel: 16 mm
Max. thickness - stainless steel: 12 mm
Strokes: 8 1/min
Cutting angle: 3 °
Number of downholders: 7 pcs.
Back gauge: 500 mm
Motor power: 22.5 kW
Oiltank: 250 l
Table height: 950 mm
Length: 2100 mm
Width: 1400 mm
Height: 2000 mm
Weight: 5000 kg

Cutting length: 1530 mm
Max. thickness - mild steel: 12 mm
Max. thickness - stainless steel: 9 mm
Strokes: 8 1/min
Cutting angle: 3 °
Number of downholders: 8 pcs.
Back gauge: 500 mm
Motor power: 15 kW
Oiltank: 180 l
Table height: 950 mm
Length: 2200 mm
Width: 1200 mm
Height: 1800 mm
Weight: 3400 kg

Cutting length: 1280 mm
Max. thickness - mild steel: 12 mm
Max. thickness - stainless steel: 9 mm
Strokes: 9 1/min
Cutting angle: 3 °
Number of downholders: 7 pcs.
Back gauge: 500 mm
Motor power: 15 kW
Oiltank: 180 l
Table height: 950 mm
Length: 1950 mm
Width: 1200 mm
Height: 1800 mm
Weight: 3200 kg

Cutting length: 1030 mm
Max. thickness - mild steel: 10 mm
Max. thickness - stainless steel: 6 mm
Strokes: 10 1/min
Cutting angle: 3 °
Number of downholders: 7 pcs.
Back gauge: 5000 mm
Motor power: 11 kW
Oiltank: 100 l
Table height: 900 mm
Length: 1550 mm
Width: 1150 mm
Height: 1600 mm
Weight: 1900 kg

Cutting length: 1030 mm
Max. thickness - mild steel: 8 mm
Max. thickness - stainless steel: 5 mm
Strokes: 14 1/min
Cutting angle: 3 °
Number of downholders: 7 pcs.
Back gauge: 500 mm
Motor power: 7.5 kW
Oiltank: 100 l
Table height: 900 mm
Length: 1550 mm
Width: 1150 mm
Height: 1600 mm
Weight: 1800 kg

Cutting length: 1030 mm
Max. thickness - mild steel: 6 mm
Max. thickness - stainless steel: 4 mm
Strokes: 14 1/min
Cutting angle: 3 °
Number of downholders: 7 pcs.
Back gauge: 500 mm
Motor power: 5.5 kW
Oiltank: 100 l
Table height: 900 mm
Length: 1550 mm
Width: 1150 mm
Height: 1600 mm
Weight: 1700 kg

Cutting length: 6080 mm
Max. thickness - mild steel: 13 mm
Max. thickness - stainless steel: 10 mm
Gap in side frame: 350 mm
Strokes: 10 1/min
Cutting angle: 0.5 - 2.5 °
Number of downholders: 29 pcs.
Pressure of downholder: 58 to
Back gauge: 1000 mm
Back gauge speed: 200 mm/s
Motor power: 37 kW
Oiltank: 400 l
Support arms: 6 pcs.
Table height: 950 mm
Table width: 650 mm
Table length: 6375 mm
Length: 7400 mm
Width: 2200 mm
Total width with support arm und protection fence: 3700 mm
Height: 2900 mm
Weight: 33820 kg

Cutting length: 6080 mm
Max. thickness - mild steel: 6 mm
Max. thickness - stainless steel: 4 mm
Gap in side frame: 350 mm
Strokes: 10 1/min
Cutting angle: 0.5 - 2 °
Number of downholders: 29 pcs.
Pressure of downholder: 20 to
Back gauge: 1000 mm
Back gauge speed: 200 mm/s
Motor power: 22 kW
Oiltank: 200 l
Support arms: 5 pcs.
Table height: 900 mm
Table width: 630 mm
Table length: 6370 mm
Length: 7300 mm
Width: 2150 mm
Total width with support arm und protection fence: 3400 mm
Height: 2750 mm
Weight: 25500 kg

Cutting length: 3080 mm
Max. thickness - mild steel: 6 mm
Max. thickness - stainless steel: 4 mm
Gap in side frame: 350 mm
Strokes: 20 1/min
Cutting angle: 0.5 - 2 °
Number of downholders: 16 pcs.
Pressure of downholder: 20 to
Back gauge: 1000 mm
Back gauge speed: 200 mm/s
Motor power: 11 kW
Oiltank: 125 l
Support arms: 3 pcs.
Table height: 820 mm
Table width: 494 mm
Table length: 3280 mm
Length: 4100 mm
Width: 2050 mm
Total width with support arm und protection fence: 3650 mm
Height: 1950 mm
Weight: 7980 kg

Swing over bed: 500 mm
Distance between centers: 1500 mm
Centre height: 250 mm
Spindle bore: 80 mm
swing over cross slide: 300 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 8
Spindle taper: 80 M
Spindle speed steps: 21
Spindle revs: Array rpm
Number of feeds: 120
Longitudinal feed range: 0.04 - 12 mm/r
Cross feed range: 0.02 - 6 mm/r
Number of threads: 64
Metric thread range: 0.5 - 120 mm
Inch thread range: Array Tpi
Module thread range: 0.125 - 30
DP thread range: Array
Cross slide travel: 315 mm
Top slide travel: 130 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 230 mm
Motor power: 7.5 kW
Length: 3100 mm
Width: 1250 mm
Height: 1400 mm
Weight: 2820 kg

Cutting length: 3100 mm
Max. thickness - mild steel: 4 mm
Strokes: 42 1/min
Cutting angle: 1 °
Back gauge: 750 mm
Motor power: 7.5 kW
Support arms: 2 pcs.
Table height: 800 mm
Table width: 450 mm
Length: 3700 mm
Width: 2300 mm
Height: 1350 mm
Weight: 3730 kg

pressing capacity: 400 to
Bending length: 4050 mm
Axes: Y1 / Y2 / X Achse
Stroke: 365 mm
Inside distance between side frames: 3400 mm
Gap in side frame: 510 mm
Daylight: 630 mm
Power concept: hydraulic
rapid speed Y-axis: 160 mm/s
Working speed Y-axis: 10
Retractionspeed Y-axis: 140
Back gauge speed X-axis: 500
Back gauge speed R-axis: 350 mm/s
Back gauge travel R-axis: 250 mm
Table height: 1050 mm
Table width: 154 mm
Oiltank: 250 l
Motor power: 37 kW
Length: 5750 mm
Width: 2110 mm
Height: 3640 mm
Weight: 27760 kg

Bending length: 3050 mm
Max. bending capacity - mild steel: 12
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 12 mm
Max. plate thickness without prebending at D=1,3x upper roll diam. - mild steel: 6.5 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 8 mm
Max. plate thickness with prebending at D=1,3x upper roll diam. - mild steel: 8 mm

Bending length: 3050 mm
Max. bending capacity - mild steel: 7
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 7 mm
Max. plate thickness without prebending at D=1,3x upper roll diam. - mild steel: 4 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 5 mm
Max. plate thickness with prebending at D=1,3x upper roll diam. - mild steel: 5 mm

Bending length: 2500 mm
Max. bending capacity - mild steel: 27
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 27 mm
Max. plate thickness without prebending at D=1,3x upper roll diam. - mild steel: 18 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 23 mm
Max. plate thickness with prebending at D=1,3x upper roll diam. - mild steel: 20 mm

pressing capacity: 80 to
Cylinder fix or moveable: horizontal moveable
Stroke: 250 mm
Distance between columns: 1040 mm
Distance between table and toolholder: 865 mm
Piston diameter: 200x120 mm
Working speed: 5 mm/s
Retraction speed: 10 mm/s
Length: 1710 mm
Width: 700 mm
Height: 2100 mm
Weight: 835 kg

pressing capacity: 40 to
Tonnage rating point: 4 mm
Table length: 630 mm
Table width: 450 mm
Hole in table: 160 mm
Stroke: 3 - 75 mm
Strokes: 154 1/min
Ram: 415 x 275 mm
Ram guides: 8
Ram adjustment: 75 mm
Ram hole: 40 mm
Throat depth: 230 mm
Daylight: 293 mm
Motor: 4 kW
Length: 1174 mm
Width: 1540 mm
Height: 2200 mm
Weight: 2850 kg

Jaw opening: 120 mm
jaw height: 40 mm
Opening of upper beam: 200 mm
Weight: 33 kg

Jaw opening: 100 mm
jaw height: 32 mm
Opening of upper beam: 135 mm
Weight: 13 kg

Jaw opening: 80 mm
jaw height: 28 mm
Opening of upper beam: 120 mm
Weight: 12 kg

Jaw opening: 80 mm
jaw height: 28 mm
Weight: 12 kg

Jaw opening: 150 mm
jaw height: 40 mm
Weight: 33 kg

Drilling capacy mild steel: 30 mm
Taper: MK 3
Distance spindle - column: 280 mm
Revs: Stufe 1: 125 - 2000, Stufe 2: 250 - 4000 r.p.m.
Motor: 0,9 / 1,45 kW kW
Tapping capacity: M20
Feeds: 0 - 300 mm/r
Distance spindle - table: 240 - 790 mm
Table: 420 x 340 mm
Quill travel: 125 mm
Length: 820 mm
Width: 520 mm
Height: 1900 mm
Weight: 320 kg

Shaft diameter: 30
Upper roll diameter: 148 mm
Lower roll diameter: 118 mm
Driven rolls: 2
Motor power: 0.7 / 0,85 kW
Speed: 2/4 m/min
Flat steel vertical position (section / min. diameter): 50x10 mm / 1.800 mm, 20x6 mm / 300 mm
Flat steel horizontal position (section / min. diameter): 80x15 mm / 700 mm, 30 x 6 mm / 400 mm
Square bar (section / min. diameter): 30x30 mm / 900 mm, 10x10 mm / 200 mm
Round bar (section / min. diameter): Ø 30 mm / 900 mm, Ø 10 mm / 200 mm
Tube (section / min. diameter): Ø 60x1,5 mm / 1.000 mm, Ø 25x1,5 mm / 600 mm, 1 1/2"x2,9 mm / 600 mm, 1/4"x1,8 mm / 300 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 50x30x3 mm / 1.200 mm, 40x20x2 mm / 800 mm
Form tube square (section / min. diameter): 40x40x3 mm / 1.200 mm, 30x30x2 mm / 800 mm
Angle leg outside (Querschnitt / min. Durchmesser): 40x40x5 mm / 600 mm, 30x30x4 mm / 300 mm
Angle leg inside (section / min. diameter): 35x35x5 mm / 600 mm, 30x30x4 mm / 400 mm
Length: 600 mm
Width: 800 mm
Height: 1450 mm
Weight: 220 kg

Cutting length: 3100 mm
Max. thickness - mild steel: 6 mm
Max. thickness - stainless steel: 4 mm
Gap in side frame: 50 mm
Strokes: 15 1/min
Cutting angle: 1.5 °
Number of downholders: 16 pcs.
Pressure of downholder: 14 to
Back gauge: 1000 mm
Back gauge speed: 200 mm/s
Motor power: 15 kW
Oiltank: 200 l
Support arms: 2 pcs.
Table height: 865 mm
Table width: 500 mm
Table length: 3515 mm
Length: 4110 mm
Width: 2200 mm
Total width with support arm und protection fence: 3700 mm
Height: 2100 mm
Weight: 7300 kg

Shaft diameter: 50
Rolls diameter: 155 mm
Driven rolls: 2
Motor power: 1.5 kW
Speed: 4 m/min
Flat steel vertical position (section / min. diameter): 60x10 mm / 500 mm, 40x10 mm / 400 mm
Flat steel horizontal position (section / min. diameter): 100x15 mm / 450 mm, 60 x 10 mm / 350 mm
Square bar (section / min. diameter): 35x35 mm / 900 mm, 20x20 mm / 300 mm
Round bar (section / min. diameter): Ø 35 mm / 600 mm, Ø 30 mm / 400 mm
Tube (section / min. diameter): Ø 70x2 mm / 1.000 mm, Ø 30x2 mm / 500 mm, 2"x2,9 mm / 1.000 mm, 1"x2,3 mm / 350 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 70x30x2 mm / 1.200 mm, 50x40x3 mm / 1.200 mm
Form tube square (section / min. diameter): 50x50x3 mm / 1.700 mm, 40x40x3 mm / 600 mm
Angle leg outside (Querschnitt / min. Durchmesser): 50x50x5 mm / 800 mm, 40x40x5 mm / 600 mm
Angle leg inside (section / min. diameter): 50x50x6 mm / 1.000 mm, 30x30x3 mm / 500 mm
Length: 1050 mm
Width: 750 mm
Height: 1450 mm
Weight: 390 kg

pressing capacity: 100 to
Stroke: 600 mm
Table: 900 x 500 mm
Daylight: 800 mm
Throat depth: 400 mm
Rapid speed: 220 mm/s
Working speed: 1 - 20 mm/s
Retraction speed: 250 mm/s
Motor: 14 kW
Working pressure: 30 - 239 bar
Length: 1900 mm
Width: 1700 mm
Height: 4400 mm
Weight: 6000 kg

Swing over bed: 600 mm
Distance between centers: 2000 mm
Centre height: 300 mm
Spindle bore: 80 mm
swing over cross slide: 400 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 8
Spindle taper: 90 M
Spindle speed steps: 21
Spindle revs: 20 - 2000 rpm
Number of feeds: 120
Longitudinal feed range: 0.04 - 12 mm/r
Cross feed range: 0.02 - 6 mm/r
Number of threads: 64
Metric thread range: 0.5 - 120 mm
Inch thread range: 60 - 1/4 Tpi
Module thread range: 0.125 - 30
Cross slide travel: 315 mm
Top slide travel: 130 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 230 mm
Motor power: 7.5 kW
Length: 3600 mm
Width: 1250 mm
Height: 1400 mm
Weight: 3110 kg

Saw blade diameter: 315 mm
Saw blade dimensions: 315x32x63 mm
Saw blade speed: 45 / 90 rpm
Cutting capacity 0°: rund 105 mm / quadratisch 85 x 85 / rechteckig 120 x 60
Cutting capacity 45° right: rund 90 mm / quadratisch 80 x 80 / rechteckig 90 x 60
Motor: 4.7 kW
Width: 600 mm
Depth: 1000 mm
Height: 1400 mm
Weight: 200 kg

Saw blade diameter: 315 mm
Saw blade dimensions: 315x32x63 mm
Saw blade speed: 45 / 90 rpm
Mitre left: 45 °
Mitre right: 45 °
Cutting capacity 0°: rund 105 mm / quadratisch 85 x 85 / rechteckig 120 x 60
Cutting capacity 45° right: rund 90 mm / quadratisch 80 x 80 / rechteckig 90 x 60
Cutting capacity 45° left: rund 90 mm / quadratisch 80 x 80 / rechteckig 90 x 60
Motor: 1,3 - 1,8 kW
Width: 600 mm
Depth: 1000 mm
Height: 1400 mm
Weight: 200 kg

pressing capacity: 100 to
Stroke: 400 mm
Table: 800 x 500 mm mm
Daylight: 500 mm
Rapid speed: 110 mm/s
Working speed: 10 mm/s
Retraction speed: 160 mm/s
Motor: 11 kW
Working pressure: 250 bar
Length: 1900 mm
Width: 1700 mm
Height: 2930 mm
Weight: 5500 kg

Bending length: 1550 mm
Max. bending capacity - mild steel: 3
Upper roll diameter: 110 mm
Bending speed: 3 m/min
Motor power: 2.2 kW
Length: 2700 mm
Width: 750 mm
Height: 1000 mm
Weight: 1200 kg

Bending length: 2050 mm
Max. bending capacity - mild steel: 10
Max. plate thickness without prebending - mild steel: 10 mm
Max. plate thickness with prebending - mild steel: 8 mm
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 10 mm
Max. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 8 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 8 mm
Max. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 6 mm
Upper roll diameter: 200 mm
Lower roll diameter: 200 mm
Lateral roll diameter: 180 mm
Bending speed: 6 m/min
Length: 3850 mm
Width: 1350 mm
Height: 1290 mm
Weight: 3750 kg

Bending length: 2050 mm
Max. bending capacity - mild steel: 8
Max. plate thickness without prebending - mild steel: 8 mm
Max. plate thickness with prebending - mild steel: 6 mm
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 8 mm
Max. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 6 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 6 mm
Max. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 4 mm
Upper roll diameter: 180 mm
Lower roll diameter: 180 mm
Lateral roll diameter: 150 mm
Bending speed: 5 m/min
Length: 3850 mm
Width: 1350 mm
Height: 1290 mm
Weight: 3300 kg

Bending length: 1270 mm
Max. bending capacity - mild steel: 5
Max. plate thickness without prebending - mild steel: 5 mm
Max. plate thickness with prebending - mild steel: 4 mm
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 5 mm
Max. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 4 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 4 mm
Max. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 3 mm
Upper roll diameter: 130 mm
Lower roll diameter: 130 mm
Lateral roll diameter: 130 mm
Bending speed: 5 m/min
Motor: 2,2 + 1,1 kW
Length: 3020 mm
Width: 1150 mm
Height: 1110 mm
Weight: 2150 kg

Max. Blechstärke - Baustahl: 3.5 mm
Ausladung: 750 mm
Motor: 2 kW
Geschwindigkeit: 6 m/min
Rondendurchmesser min/max: 200/1200 mm
Länge: 2000 mm
Breite: 600 mm
Höhe: 1400 mm
Gewicht: 750 kg

Max. sheet thickness - mild steel: 5 mm
Max. blank diameter: 2000 mm
Min. blank diameter: 250 mm
Length: 3000 mm
Width: 750 mm
Height: 1400 mm
Weight: 1350 kg

Sheet Thickness - mild steel: 0.4 - 2 mm
Max. sheet width: 400 mm
Max. cross-section: 300 mm
Feed roll diameter: 63 mm
Feeding speed: 150 m/min
Feeding acceleration: 10 m/s²

Sheet Thickness - mild steel: 0.4 - 2 mm
Max. sheet width: 300 mm
Max. cross-section: 300 mm
Feed roll diameter: 63 mm
Feeding speed: 150 m/min
Feeding acceleration: 10 m/s²

Sheet Thickness - mild steel: 0.4 - 2 mm
Max. sheet width: 200 mm
Max. cross-section: 300 mm
Feed roll diameter: 63 mm
Feeding speed: 150 m/min
Feeding acceleration: 10 m/s²

Sheet Thickness - mild steel: 0.4 - 2 mm
Max. sheet width: 100 mm
Max. cross-section: 200 mm
Feed roll diameter: 63 mm
Feeding speed: 150 m/min
Feeding acceleration: 10 m/s²

Bending length: 1050 mm
Sheet thickness (420 N/mm²): 1.5 mm
Max. thickness - stainless steel: 1 mm
Max. thickness - aluminium: 2.2 mm
Max. bending angle: 150 °
Back gauge manual: 500 mm
Max. opening width without tools: 200 mm
Upper tool: sectioned, 45°
Bending flange: adjustment 35 mm
Length: 1300 mm
Width: 750 mm
Height: 1515 mm
Weight: 280 kg

Blade length: 197 mm
Sheet thickness (420 N/mm²): 4 mm
Sheet thickness (600 N/mm²): 2 mm
Strokes: 20 1/min
Angle: 90 °
Motor: 4 kW
Length: 890 mm
Width: 780 mm
Height: 1115 mm
Weight: 550 kg

Punching power: 110 ton
Throat depth: 610 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 420/20 bzw. 28/28 mm
Stroke: 80 mm
Strokes: 28 1/min
Flat steel: 600x15 / 400x20 mm
Angle steel: 152x152x13 mm
Round / square steel: 50 mm
Notcher: 13x52x90 mm
Motor: 9 kW
Length: 2690 mm
Width: 1400 mm
Height: 2200 mm
Weight: 3300 kg