Kaeser SK26 Air compressor, Serial:2610493, Air compressor, 15Kw, 7.5Bar, rated motor speed 3000min, 3Ph

Kaeser SK26 Air compressor, Serial: 264957, Air compressor, 15Kw, 7.5Bar, 2.4M3/min, 3Ph

Busch Mink MM1252AV Vacuum pumps, Vacuum Pump, 5.1Kw motor, 3Ph

Kaeser 2000L Air receiver tank, 2000L air receiver tank, 11Bar, temp 50'C

Koppens BVE400HD Former, Stainless Koppens forming machine, comes with lots of different forming plates for different size products, previously used for hamburgers, belt 400mm, variable speed, up to 50 cycles per min, 3Ph

Kronen KUJ Dicer, Stainless machine, can be used for dicing, slicing and strip cutting, V cuts veg from 2 to 12mm and dices from 3mm to 20mm, up to 3000Kg per hour depending on product, with manual, mobile, 3Ph

Multivac AG6 swing top vacuum packer Swing top vac packer, twin chamber, 450mm sealing bars, Busch vac pump, mobile, 3Ph

Forberg 1000LH Twin shaft paddle mixer, Serial: 1720, Stainless twin shaft paddle mixer, 1000Kgs, bottom discharge doors, inspection hatch on each side, 3Ph

Packo FP2 Sanitary pump, 2 x Packo sanitary pumps, easily cleanable process pumps ideal for dairies, breweries, beverage industry, distilleries and more, 3Ph

NNP Stainless trolleys 2 x stainless trolleys, platform 800mm x 500mm, mobile

NNP Hopper and screw feed, Stainless, 1000Kg hopper, discharge screw, screw diameter 200mm, screw length 2800mm

Kenplaat mixing tank, Stainless 1500l mixing tank, top mounted motor, level detection, side bottom discharge

NNP 300l holding vessel, Stainless 300L holding tank horizontal, with level detection

KSB ETALINE Z Volite casing pump, 2019, single stage volute casing pump inline design as twin pump, water meters, variable speed, 3Kw motors, 3Ph

Kaeser SK26 Air compressor, serial: 2610494, Air compressor, 15Kw, 7.5Bar, rate motor speed 3000/min, 3Ph

Decalinox holding tank Stainless 400L holding tank, with lid, side bottom discharge

Decalinox holding tank Stainless 200L holding tank, with lid, side bottom discharge

VMI 2400L high shear mixing vessel, 2012, Stainless, 2400l jacketed mixing vessel, top mounted agitation and scrape surface, central high shear mixing shaft, with centrifugal pump, 3Ph

Morgana PC50 Evaporator Serial: 1402055 Three fan, ceiling mounted evaporator, 3Ph

Fristam FP66-40 Centrifugal pump, Stainless, 12Kw, centrifugal pump, 3Ph

Dedy Chocolate shavings machine, Electric chocolate shavings machine, for blocks of 2.5kg - 5kg, 1Ph

Bartscher A120 Convection oven, 2012, stainless oven, up to 300,C, timer controls, four trays, 1Ph

NNP Egg slicer Stainless, rotary egg slicer, pneumatic, 1Ph

Marco Linemaster IV scales stainless platform scales, weighing from 20g - 20,000g, platform 500mm x 400mm, mobile, 1Ph (two in stock)

Marco Linemaster IV scales, stainless platform scales, weighing from 20g - 20,000g, platform 600mm x 500mm, mobile, 1Ph (four in stock)

This Gimret UHT system is a continuous installation for sterilizing by heating, to ensure that a prepared liquid mixture is free from bacterial endospores, the mixture is passed through a sterilizer prior to the drying process. To obtain a continuous flow in the sterilizer, the material is first accommodated in a buffer tank from which the sterilizer is fed by using a dosing pump (low pressure). To kill the bacterial endospores a temperature of at least 135°C is required for a period of 5-7 seconds. To reach this temperature, steam is injected into the mixture that is dosed from the dosing pump. A meandering pipe works then realizes the required residence time at a set temperature of minimum 135°C.

Rollenbahnlänge: 3600 mm
Rollenbreite: 700 mm
Tischhöhe: 700 mm
Rollenbahnbreite: 900 mm
Rollendurchmesser: 140 mm
Tragkraft: kg
Anschlag: 450 mm
Antrieb: kW
Abmessung L-B-H: 3,7x0,9x1,3 m
Gewicht: 0,7 t

Rollenbahnlänge: 2900 mm
Rollenbreite: 700 mm
Tischhöhe: 700 mm
Rollenbahnbreite: 900 mm
Rollendurchmesser: 140 mm
Tragkraft: kg
Anschlag: 450 mm
Antrieb: kW
Abmessung L-B-H: 3,0x0,9x1,3 m
Gewicht: 0,7 t

Schnittdurchmesser: 1020 mm
Sägebandlänge: 11.430 x 80 x 1,6 mm
Schnittbreite: 1,6 mm
Schnittbereich: 1020x1260 mm
Steuerung: CNC
Schnittgeschwindigkeit: 15-190 m/min
Antriebsleistung: 11 kW
Tischbelastung: 20 t
Gesamtleistungsbedarf: 20 kW
Maschinengewicht ca.: 21,1 t
Raumbedarf ca.: m

Spindeldurchmesser: 110 mm
x-Weg: 2000 mm
y-Weg: 1200 mm
Spindeldrehzahlen: 6-1250 U/min
Tischfläche: 1400x900 mm
Spindelantriebmotor: 12 kW
Spindelaufnahme ISO: 50
Spindelweg: 800 mm
z-Weg: 1000 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: 20 t
Raumbedarf ca.: 5x3x2 m

Saw frame: Double column
Band dimensions: 7000x41x1,3 mm
Band speed continous: 15 - 120 m/min
Cutting capacity 0° round: 560 mm
Cutting capacity 0° square: 540 mm
Cutting capacity 0° flat: 810 x 530 mm
Cutting capacity 45°: round 520 mm, square 520 mm, rectangular 520 x 540 mm
Cutting capacity - 45°: round 520 mm, square 520 mm, rectangular 520 x 540 mm
Cutting capacity - 60°: round 330 mm, square 330 mm, rectangular 330 x 540 mm
Working height: 875 mm
Hydraulic motor: 1.1 kW
Motor: 4 kW
Coolant pump motor: 0.12 kW
Length: 3850 mm
Width: 1700 mm
Height: 2450 mm
Weight: 3400 kg

Cutting length: 2050 mm
Max. thickness - mild steel: 4 mm
Strokes: 42 1/min
Back gauge: 750 mm
Motor power: 7.5 kW
Table height: 800 mm
Table width: 450 mm
Length: 2700 mm
Width: 2300 mm
Height: 1350 mm
Weight: 2800 kg

Punching power: 110 ton
Throat depth: 500 mm
Max. diameter at sheet thickness (mild steel): 40x20 mm
Max. number of strokes at 20 mm stroke: 28 1/min
Motor: 9 kW
Length: 2080 mm
Width: 1300 mm
Height: 2050 mm
Weight: 3150 kg

Ref. no.: 18383
Hersteller: DEMAG
Year of construction: 2008

Clamping unit
Clamping force: 420 ton
Opening stroke: 770 mm
Distance between tie bars: 820 X 820 mm
Mould height min.: 380 mm
Mould height max.: 825 mm
Platen size (h x v): 1200 X 1100 mm

Injection unit
Screw diameter: 60 mm
Injection volume: 890 cm³
Shot weight: 810 g
Injection pressure: 2420 bar

Measurements and weight
Dimensions: 8,2 X 2,2 X 2,4 m
Machine weight: 22300 kg

Additional information & extras
Core pull: 4 pcs
Air valve: 7 pcs
Hot runner systems: 8 pcs.

Swing over bed: 630 mm
Distance between centers: 2000 mm
Centre height: 315 mm
Spindle bore: 103 mm
swing over cross slide: 430 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 11
Spindle taper: 120 M
Spindle speed steps: 21
Spindle revs: Array rpm
Number of feeds: 120
Longitudinal feed range: 0.04 - 12 mm/r
Cross feed range: 0.02 - 6 mm/r
Metric thread range: 0.5 - 120 mm
Inch thread range: 60 - 1/4 Tpi
Module thread range: 0.125 - 30
DP thread range: Array
Cross slide travel: 315 mm
Top slide travel: 90 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 230 mm
Motor power: 11 kW
Weight: 3310 kg

Shaft diameter: 35
Upper roll diameter: 137 mm
Lower roll diameter: 137 mm
Driven rolls: 3
Motor power: 1.1 kW
Speed: 7 m/min
Flat steel vertical position (section / min. diameter): 35x8 mm / 300 mm
Flat steel horizontal position (section / min. diameter): 50x12 mm / 400 mm
Square bar (section / min. diameter): 18x18 mm / 250 mm
Round bar (section / min. diameter): Ø 22 mm / 200 mm
Tube (section / min. diameter): Ø 40x1,5 mm / 500 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 30x15x2,5 mm / 500 mm
Form tube square (section / min. diameter): 25x25x2 mm / 450 mm
Angle leg outside (Querschnitt / min. Durchmesser): 35x35x5 mm / 400 mm
Angle leg inside (section / min. diameter): 30x30x4 mm / 550 mm
Length: 1050 mm
Width: 500 mm
Height: 1250 mm
Weight: 350 kg

Shaft diameter: 30
Upper roll diameter: 148 mm
Lower roll diameter: 118 mm
Driven rolls: 2
Motor power: 0.7 / 0,85 kW
Speed: 2/4 m/min
Flat steel vertical position (section / min. diameter): 50x10 mm / 1.800 mm, 20x6 mm / 300 mm
Flat steel horizontal position (section / min. diameter): 80x15 mm / 700 mm, 30 x 6 mm / 400 mm
Square bar (section / min. diameter): 30x30 mm / 900 mm, 10x10 mm / 200 mm
Round bar (section / min. diameter): Ø 30 mm / 900 mm, Ø 10 mm / 200 mm
Tube (section / min. diameter): Ø 60x1,5 mm / 1.000 mm, Ø 25x1,5 mm / 600 mm, 1 1/2"x2,9 mm / 600 mm, 1/4"x1,8 mm / 300 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 50x30x3 mm / 1.200 mm, 40x20x2 mm / 800 mm
Form tube square (section / min. diameter): 40x40x3 mm / 1.200 mm, 30x30x2 mm / 800 mm
Angle leg outside (Querschnitt / min. Durchmesser): 40x40x5 mm / 600 mm, 30x30x4 mm / 300 mm
Angle leg inside (section / min. diameter): 35x35x5 mm / 600 mm, 30x30x4 mm / 400 mm
Length: 600 mm
Width: 800 mm
Height: 1450 mm
Weight: 220 kg

X-axis: 3000 mm
Positioning speed: 24 m/min
Repeat accuracy: 2 mm
Weight: 250 kg

Swing over bed: 760 mm
Distance between centers: 3000 mm
Centre height: 380 mm
Spindle bore: 132 mm
swing over cross slide: 520 mm
Width of bed: 560 mm
Spindle nose / DIN55027: 11
Spindle taper: 140 M
Revs continuous variable in gear steps: 3
Revs continuous variable: 7 - 42, 28 - 170, 165 - 1.015 rpm
Number of feeds: 150
Longitudinal feed range: 0.039 - 18 mm/r
Cross feed range: 0.02 - 9 mm/r
Metric thread range: 0.5 - 180 mm
Inch thread range: 60 - 1/6 Tpi
Module thread range: 0.125 - 45
DP thread range: Array
Cross slide travel: 410 mm
Top slide travel: 150 mm
Tailstock quill diameter: 105 mm
Tailstock quill taper: 6 MK
Tailstock travel: 225 mm
Motor power: 15 kW
Weight: 4470 kg

Swing over bed: 600 mm
Distance between centers: 2000 mm
Centre height: 300 mm
Spindle bore: 80 mm
swing over cross slide: 400 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 8
Spindle taper: 90 M
Revs continuous variable in gear steps: 3
Revs continuous variable: 8-62, 62-500, 250-2.000 rpm
Number of feeds: 160
Number of threads: 64
Metric thread range: 0.5 - 120 mm
Inch thread range: 120 - 1/4 Tpi
Module thread range: 0.125 - 30
Cross slide travel: 315 mm
Top slide travel: 130 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 230 mm
Motor power: 11 kW
Length: 3600 mm
Width: 1500 mm
Height: 1650 mm
Weight: 3110 kg

Bending length: 2050 mm
Max. bending capacity - mild steel: 10
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 10 mm
Max. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 8 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 8 mm
Max. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 6 mm
Upper roll diameter: 200 - 220 mm
Lower roll diameter: 200 - 220 mm
Lateral roll diameter: 160 mm
Bending speed: 1,5 / 6 m/min
Motor power: 5.5 kW
Length: 4400 mm
Width: 1150 mm
Height: 1250 mm
Weight: 3950 kg

Bending length: 2050 mm
Max. bending capacity - mild steel: 8
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 8 mm
Max. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 6 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 6 mm
Max. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 4 mm
Upper roll diameter: 180 mm
Lower roll diameter: 180 mm
Lateral roll diameter: 150 mm
Bending speed: 1,5 / 6 m/min
Motor power: 5.5 kW
Length: 4400 mm
Width: 1150 mm
Height: 1250 mm
Weight: 3790 kg

Saw frame: Double column
Band dimensions: 8200x41x1,3 mm
Band speed continous: 20-100 m/min
Cutting capacity 0° round: 810 mm
Cutting capacity 0° square: 750 mm
Cutting capacity 0° flat: 910x750 mm
Cutting capacity 45°: rund 600 mm, quadrat 600 mm, rechteck 750 x 600 mm
Cutting capacity 60°: rund 360 mm, quadrat 360 mm, rechteck 750 x 360 mm
Working height: 725 mm
Motor: 4 kW
Coolant pump motor: 0.12 kW
Length: 4020 mm
Width: 1600 mm
Height: 2450 mm
Weight: 3970 kg

Ref. no.: 18368
Hersteller: ARBURG
Year of construction: 1997

Clamping unit
Clamping force: 50 ton
Opening stroke: 350 mm
Distance between tie bars: 320 X 320 mm
Mould height min.: 300 mm
Mould height max.: 550 mm
Platen size (h x v): 446 X 446 mm

Injection unit
Screw diameter: 30 mm
Injection volume: 85 cm³
Shot weight: 75 g
Injection pressure: 2200 bar

Measurements and weight
Dimensions: 3,25 x 1.15 x 2,0 m
Machine weight: 2250 kg

Bending length: 4010 mm
Bending capacity steel 400 N/mm²: 1.5 mm
Bending capacity Alu 190 N/mm²: 2 mm
No. of stand and tension arm units: 4

pressing capacity: 150 to
Cylinder fix or moveable: fix
Stroke: 300 mm
Daylight: 610 mm
Distance between columns: 1020 mm
Rapid speed: 9 mm/s
Working speed: 5 mm/s
Retraction speed: 10 mm/s
Table: 600x1020 mm
Hole in table: 100 mm
Hole distance: 190 mm
Length: 2110 mm
Width: 1000 mm
Height: 2470 mm
Weight: 2450 kg

Bending length: 1550 mm
Max. bending capacity - mild steel: 4.5
Max. plate thickness without prebending - mild steel: 4.5 mm
Max. plate thickness with prebending - mild steel: 3.5 mm
Max. plate thickness without prebending at D=5x upper roll diam. - mild steel: 4.5 mm
Max. plate thickness without prebending at D=1,5x upper roll diam. - mild steel: 3.5 mm
Max. plate thickness with prebending at D=5x upper roll diam. - mild steel: 3.5 mm
Max. plate thickness with prebending at D=1,5x upper roll diam. - mild steel: 2.5 mm
Upper roll diameter: 130 mm
Lower roll diameter: 130 mm
Lateral roll diameter: 130 mm
Bending speed: 5 m/min
Motor power: 2,2 + 1,1 kW
Length: 3300 mm
Width: 1150 mm
Height: 1110 mm
Weight: 2370 kg

pressing capacity: 15 to
Tonnage rating point: 1.4 mm
Table length: 320 mm
Table width: 490 mm
Hole in table: 130 mm
Stroke: 1 - 40 mm
Strokes: 200 1/min
Ram guides: 4
Ram adjustment: 40 mm
Ram hole: 30 mm
Throat depth: 200 mm
Daylight: 215 mm
Motor: 1.5 kW
Length: 1160 mm
Width: 1180 mm
Height: 1730 mm
Weight: 922 kg

Punching power: 110 ton
Max. diameter at sheet thickness (mild steel): 4-30 mm

Punching power: 50 ton
Throat depth: 130 mm
Max. diameter at sheet thickness (mild steel): 13/27 mm
Max. number of strokes at 20 mm stroke: 23 1/min
Motor: 3 kW
Length: 1100 mm
Width: 900 mm
Height: 1550 mm
Weight: 355 kg