2
Metal working and machine toolsLathes
Swing over bed: 760 mm
Distance between centers: 3000 mm
Centre height: 380 mm
Spindle bore: 132 mm
swing over cross slide: 520 mm
Width of bed: 560 mm
Spindle nose / DIN55027: 11
Spindle taper: 140 M
Revs continuous variable in gear steps: 3
Revs continuous variable: 7 - 42, 28 - 170, 165 - 1.015 rpm
Number of feeds: 150
Longitudinal feed range: 0.039 - 18 mm/r
Cross feed range: 0.02 - 9 mm/r
Metric thread range: 0.5 - 180 mm
Inch thread range: 60 - 1/6 Tpi
Module thread range: 0.125 - 45
DP thread range: Array
Cross slide travel: 410 mm
Top slide travel: 150 mm
Tailstock quill diameter: 105 mm
Tailstock quill taper: 6 MK
Tailstock travel: 225 mm
Motor power: 15 kW
Weight: 4470 kg
Swing over bed: 760 mm
Distance between centers: 3000 mm
Centre height: 380 mm
Spindle bore: 132 mm
swing over cross slide: 520 mm
Width of bed: 560 mm
Spindle nose / DIN55027: 11
Spindle taper: 140 M
Revs continuous variable in gear steps: 3
Revs continuous variable: 7 - 42, 28 - 170, 165 - 1.015 rpm
Number of feeds: 150
Longitudinal feed range: 0.039 - 18 mm/r
Cross feed range: 0.02 - 9 mm/r
Metric thread range: 0.5 - 180 mm
Inch thread range: 60 - 1/6 Tpi
Module thread range: 0.125 - 45
DP thread range: Array
Cross slide travel: 410 mm
Top slide travel: 150 mm
Tailstock quill diameter: 105 mm
Tailstock quill taper: 6 MK
Tailstock travel: 225 mm
Motor power: 15 kW
Weight: 4470 kg
Distance between centers: 3000 mm
Centre height: 380 mm
Spindle bore: 132 mm
swing over cross slide: 520 mm
Width of bed: 560 mm
Spindle nose / DIN55027: 11
Spindle taper: 140 M
Revs continuous variable in gear steps: 3
Revs continuous variable: 7 - 42, 28 - 170, 165 - 1.015 rpm
Number of feeds: 150
Longitudinal feed range: 0.039 - 18 mm/r
Cross feed range: 0.02 - 9 mm/r
Metric thread range: 0.5 - 180 mm
Inch thread range: 60 - 1/6 Tpi
Module thread range: 0.125 - 45
DP thread range: Array
Cross slide travel: 410 mm
Top slide travel: 150 mm
Tailstock quill diameter: 105 mm
Tailstock quill taper: 6 MK
Tailstock travel: 225 mm
Motor power: 15 kW
Weight: 4470 kg
2
Metal working and machine toolsLathes
Swing over bed: 600 mm
Distance between centers: 2000 mm
Centre height: 300 mm
Spindle bore: 80 mm
swing over cross slide: 400 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 8
Spindle taper: 90 M
Revs continuous variable in gear steps: 3
Revs continuous variable: 8-62, 62-500, 250-2.000 rpm
Number of feeds: 160
Number of threads: 64
Metric thread range: 0.5 - 120 mm
Inch thread range: 120 - 1/4 Tpi
Module thread range: 0.125 - 30
Cross slide travel: 315 mm
Top slide travel: 130 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 230 mm
Motor power: 11 kW
Length: 3600 mm
Width: 1500 mm
Height: 1650 mm
Weight: 3110 kg
Swing over bed: 600 mm
Distance between centers: 2000 mm
Centre height: 300 mm
Spindle bore: 80 mm
swing over cross slide: 400 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 8
Spindle taper: 90 M
Revs continuous variable in gear steps: 3
Revs continuous variable: 8-62, 62-500, 250-2.000 rpm
Number of feeds: 160
Number of threads: 64
Metric thread range: 0.5 - 120 mm
Inch thread range: 120 - 1/4 Tpi
Module thread range: 0.125 - 30
Cross slide travel: 315 mm
Top slide travel: 130 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 230 mm
Motor power: 11 kW
Length: 3600 mm
Width: 1500 mm
Height: 1650 mm
Weight: 3110 kg
Distance between centers: 2000 mm
Centre height: 300 mm
Spindle bore: 80 mm
swing over cross slide: 400 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 8
Spindle taper: 90 M
Revs continuous variable in gear steps: 3
Revs continuous variable: 8-62, 62-500, 250-2.000 rpm
Number of feeds: 160
Number of threads: 64
Metric thread range: 0.5 - 120 mm
Inch thread range: 120 - 1/4 Tpi
Module thread range: 0.125 - 30
Cross slide travel: 315 mm
Top slide travel: 130 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 230 mm
Motor power: 11 kW
Length: 3600 mm
Width: 1500 mm
Height: 1650 mm
Weight: 3110 kg
6
Metal working and machine toolsSheet metal working machinesPipe-bending machines
Flexion modulus: 19 cm³
Standard steel tube: 38 x 1,5 mm
Furniture tube: 38 x 1,5 mm
FE35 (for hydraulic tubes): 35 x 3 mm
Stainless steel AISI304-318: 30 x 2 mm
Stainless steel AISI308 (food industry): 35 x 1,5 mm
Brass soft: 42 x 1,5 mm
Hard copper and aluminium: 42 x 1,5 mm
Soft copper: 50 x 2 mm
Conduit tube (TAZ): 50 x 2 mm
Mepla, Gebereit and similar: 50 x 4 mm
Roundbar solid (S275JO): 20 mm
Squarebar solid (S275JO): 10 x 25 mm
Flatsteel solid (S275JO): 25 x 20 (stehend), 25 x 16 (stehend) mm
Max. bending radius: 180 mm
Min. bending radius: 36 mm
Min. tube Ø: 10 mm
Max. bending speed: 2 r/min
Motor: 0.9 kW
Length: 245 mm
Width: 300 mm
Height: 320 mm
Weight: 23 kg
Flexion modulus: 19 cm³
Standard steel tube: 38 x 1,5 mm
Furniture tube: 38 x 1,5 mm
FE35 (for hydraulic tubes): 35 x 3 mm
Stainless steel AISI304-318: 30 x 2 mm
Stainless steel AISI308 (food industry): 35 x 1,5 mm
Brass soft: 42 x 1,5 mm
Hard copper and aluminium: 42 x 1,5 mm
Soft copper: 50 x 2 mm
Conduit tube (TAZ): 50 x 2 mm
Mepla, Gebereit and similar: 50 x 4 mm
Roundbar solid (S275JO): 20 mm
Squarebar solid (S275JO): 10 x 25 mm
Flatsteel solid (S275JO): 25 x 20 (stehend), 25 x 16 (stehend) mm
Max. bending radius: 180 mm
Min. bending radius: 36 mm
Min. tube Ø: 10 mm
Max. bending speed: 2 r/min
Motor: 0.9 kW
Length: 245 mm
Width: 300 mm
Height: 320 mm
Weight: 23 kg
Standard steel tube: 38 x 1,5 mm
Furniture tube: 38 x 1,5 mm
FE35 (for hydraulic tubes): 35 x 3 mm
Stainless steel AISI304-318: 30 x 2 mm
Stainless steel AISI308 (food industry): 35 x 1,5 mm
Brass soft: 42 x 1,5 mm
Hard copper and aluminium: 42 x 1,5 mm
Soft copper: 50 x 2 mm
Conduit tube (TAZ): 50 x 2 mm
Mepla, Gebereit and similar: 50 x 4 mm
Roundbar solid (S275JO): 20 mm
Squarebar solid (S275JO): 10 x 25 mm
Flatsteel solid (S275JO): 25 x 20 (stehend), 25 x 16 (stehend) mm
Max. bending radius: 180 mm
Min. bending radius: 36 mm
Min. tube Ø: 10 mm
Max. bending speed: 2 r/min
Motor: 0.9 kW
Length: 245 mm
Width: 300 mm
Height: 320 mm
Weight: 23 kg
3
Metal working and machine toolsSheet metal working machinesPipe-bending machines
Flexion modulus: 4 cm³
Standard steel tube: 42 x 3 mm
Furniture tube: 48 x 1,5 mm
FE35 (for hydraulic tubes): 42 x 4 mm
Stainless steel AISI304-318: 42 x 3 mm
Stainless steel AISI308 (food industry): 42 x 2,5 mm
Brass soft: 50 x 3 mm
Hard copper and aluminium: 54 x 2 mm
Soft copper: 60 x 2 mm
Conduit tube (TAZ): 60 x 2 mm
Mepla, Gebereit and similar: 50 x 4 mm
Roundbar solid (S275JO): 30 mm
Flatsteel solid (S275JO): 40x20 (liegend), 40x12 (stehend) mm
Max. bending radius: 260 mm
Min. bending radius: 10 mm
Max. bending speed: 4 r/min
Motor: 1.1 kW
Length: 400 mm
Width: 570 mm
Height: 1000 mm
Weight: 80 kg
Flexion modulus: 4 cm³
Standard steel tube: 42 x 3 mm
Furniture tube: 48 x 1,5 mm
FE35 (for hydraulic tubes): 42 x 4 mm
Stainless steel AISI304-318: 42 x 3 mm
Stainless steel AISI308 (food industry): 42 x 2,5 mm
Brass soft: 50 x 3 mm
Hard copper and aluminium: 54 x 2 mm
Soft copper: 60 x 2 mm
Conduit tube (TAZ): 60 x 2 mm
Mepla, Gebereit and similar: 50 x 4 mm
Roundbar solid (S275JO): 30 mm
Flatsteel solid (S275JO): 40x20 (liegend), 40x12 (stehend) mm
Max. bending radius: 260 mm
Min. bending radius: 10 mm
Max. bending speed: 4 r/min
Motor: 1.1 kW
Length: 400 mm
Width: 570 mm
Height: 1000 mm
Weight: 80 kg
Standard steel tube: 42 x 3 mm
Furniture tube: 48 x 1,5 mm
FE35 (for hydraulic tubes): 42 x 4 mm
Stainless steel AISI304-318: 42 x 3 mm
Stainless steel AISI308 (food industry): 42 x 2,5 mm
Brass soft: 50 x 3 mm
Hard copper and aluminium: 54 x 2 mm
Soft copper: 60 x 2 mm
Conduit tube (TAZ): 60 x 2 mm
Mepla, Gebereit and similar: 50 x 4 mm
Roundbar solid (S275JO): 30 mm
Flatsteel solid (S275JO): 40x20 (liegend), 40x12 (stehend) mm
Max. bending radius: 260 mm
Min. bending radius: 10 mm
Max. bending speed: 4 r/min
Motor: 1.1 kW
Length: 400 mm
Width: 570 mm
Height: 1000 mm
Weight: 80 kg
2
Metal working and machine toolsLathes
Swing over bed: 860 mm
Distance between centers: 3000 mm
Centre height: 430 mm
Spindle bore: 135 mm
swing over cross slide: 620 mm
Width of bed: 560 mm
Spindle nose / DIN55027: 11
Spindle taper: 140 M
Revs continuous variable: 7 - 42, 28 - 170, 165 - 1.015 rpm
Number of feeds: 150
Longitudinal feed range: 0.039 - 18 mm/r
Cross feed range: 0.02 - 9 mm/r
Metric thread range: 0.5 - 180 mm
Inch thread range: 60 - 1/6 Tpi
Module thread range: 0.125 - 45
DP thread range: 240
Cross slide travel: 435 mm
Top slide travel: 150 mm
Tailstock quill diameter: 105 mm
Tailstock quill taper: 6 MK
Tailstock travel: 225 mm
Motor power: 15 kW
Weight: 4650 kg
Swing over bed: 860 mm
Distance between centers: 3000 mm
Centre height: 430 mm
Spindle bore: 135 mm
swing over cross slide: 620 mm
Width of bed: 560 mm
Spindle nose / DIN55027: 11
Spindle taper: 140 M
Revs continuous variable: 7 - 42, 28 - 170, 165 - 1.015 rpm
Number of feeds: 150
Longitudinal feed range: 0.039 - 18 mm/r
Cross feed range: 0.02 - 9 mm/r
Metric thread range: 0.5 - 180 mm
Inch thread range: 60 - 1/6 Tpi
Module thread range: 0.125 - 45
DP thread range: 240
Cross slide travel: 435 mm
Top slide travel: 150 mm
Tailstock quill diameter: 105 mm
Tailstock quill taper: 6 MK
Tailstock travel: 225 mm
Motor power: 15 kW
Weight: 4650 kg
Distance between centers: 3000 mm
Centre height: 430 mm
Spindle bore: 135 mm
swing over cross slide: 620 mm
Width of bed: 560 mm
Spindle nose / DIN55027: 11
Spindle taper: 140 M
Revs continuous variable: 7 - 42, 28 - 170, 165 - 1.015 rpm
Number of feeds: 150
Longitudinal feed range: 0.039 - 18 mm/r
Cross feed range: 0.02 - 9 mm/r
Metric thread range: 0.5 - 180 mm
Inch thread range: 60 - 1/6 Tpi
Module thread range: 0.125 - 45
DP thread range: 240
Cross slide travel: 435 mm
Top slide travel: 150 mm
Tailstock quill diameter: 105 mm
Tailstock quill taper: 6 MK
Tailstock travel: 225 mm
Motor power: 15 kW
Weight: 4650 kg
_thumb.jpeg "Show advert")
_thumb.jpeg "Show advert")
_thumb.jpeg "Show advert")
_thumb.jpeg "Show advert")
_thumb.jpeg "Show advert")
_thumb.jpeg "Show advert")
_thumb.jpeg "Show advert")
_thumb.jpeg "Show advert")
_thumb.jpeg "Show advert")
12
Printing machineryFolding machines
Folding machine
Heidelberg-Stahlfolder KH 78-82/4KL
Year: 2011
Description:
- 16 page folder
Feeder
- Round pile feeder: RFH-82
- Pump: Becker
Folding unit
- perforation shaft
- Parallel fold unit with 4 buckle plates: BUH-82
- Perforating shaft
- First cross fold: CUH-78
- Second cross fold to the left: CUH-78
- Noise hood over the entire folding section
- Touch screen display.
- Fully automatic adjusting by display.
Delivery:
Heidelberg-Stahlfolder Twinstacker TSH-50
Year: 2011
- Vertical stack delivery with pressing and marking device
- Twin stack delivery
Folding machine
Heidelberg-Stahlfolder KH 78-82/4KL
Year: 2011
Description:
- 16 page folder
Feeder
- Round pile feeder: RFH-82
- Pump: Becker
Folding unit
- perforation shaft
- Parallel fold unit with 4 buckle plates: BUH-82
- Perforating shaft
- First cross fold: CUH-78
- Second cross fold to the left: CUH-78
- Noise hood over the entire folding section
- Touch screen display.
- Fully automatic adjusting by display.
Delivery:
Heidelberg-Stahlfolder Twinstacker TSH-50
Year: 2011
- Vertical stack delivery with pressing and marking device
- Twin stack delivery
Heidelberg-Stahlfolder KH 78-82/4KL
Year: 2011
Description:
- 16 page folder
Feeder
- Round pile feeder: RFH-82
- Pump: Becker
Folding unit
- perforation shaft
- Parallel fold unit with 4 buckle plates: BUH-82
- Perforating shaft
- First cross fold: CUH-78
- Second cross fold to the left: CUH-78
- Noise hood over the entire folding section
- Touch screen display.
- Fully automatic adjusting by display.
Delivery:
Heidelberg-Stahlfolder Twinstacker TSH-50
Year: 2011
- Vertical stack delivery with pressing and marking device
- Twin stack delivery
9
Metal working and machine toolsLathes
Swing over bed: 400 mm
Distance between centers: 1000 mm
Centre height: 200 mm
Spindle bore: 52 mm
swing over cross slide: 235 mm
Width of bed: 320 mm
Spindle nose / DIN55027: 6
Spindle taper: 6 M
Spindle speed steps: 12
Spindle revs: 50–2.240 rpm
Number of feeds: 80
Longitudinal feed range: 0.015 - 0.6 mm/r
Cross feed range: 0.0075 - 0.3 mm/r
Number of threads: 40
Metric thread range: 0.25 - 7.5 mm
Inch thread range: 120 - 4 Tpi
Module thread range: 0.0625 - 1.875
DP thread range: Array
Cross slide travel: 235 mm
Top slide travel: 110 mm
Tailstock quill diameter: 50 mm
Tailstock quill taper: 4 MK
Tailstock travel: 100 mm
Motor power: 4 kW
Length: 2750 mm
Width: 1100 mm
Height: 1600 mm
Weight: 1540 kg
Swing over bed: 400 mm
Distance between centers: 1000 mm
Centre height: 200 mm
Spindle bore: 52 mm
swing over cross slide: 235 mm
Width of bed: 320 mm
Spindle nose / DIN55027: 6
Spindle taper: 6 M
Spindle speed steps: 12
Spindle revs: 50–2.240 rpm
Number of feeds: 80
Longitudinal feed range: 0.015 - 0.6 mm/r
Cross feed range: 0.0075 - 0.3 mm/r
Number of threads: 40
Metric thread range: 0.25 - 7.5 mm
Inch thread range: 120 - 4 Tpi
Module thread range: 0.0625 - 1.875
DP thread range: Array
Cross slide travel: 235 mm
Top slide travel: 110 mm
Tailstock quill diameter: 50 mm
Tailstock quill taper: 4 MK
Tailstock travel: 100 mm
Motor power: 4 kW
Length: 2750 mm
Width: 1100 mm
Height: 1600 mm
Weight: 1540 kg
Distance between centers: 1000 mm
Centre height: 200 mm
Spindle bore: 52 mm
swing over cross slide: 235 mm
Width of bed: 320 mm
Spindle nose / DIN55027: 6
Spindle taper: 6 M
Spindle speed steps: 12
Spindle revs: 50–2.240 rpm
Number of feeds: 80
Longitudinal feed range: 0.015 - 0.6 mm/r
Cross feed range: 0.0075 - 0.3 mm/r
Number of threads: 40
Metric thread range: 0.25 - 7.5 mm
Inch thread range: 120 - 4 Tpi
Module thread range: 0.0625 - 1.875
DP thread range: Array
Cross slide travel: 235 mm
Top slide travel: 110 mm
Tailstock quill diameter: 50 mm
Tailstock quill taper: 4 MK
Tailstock travel: 100 mm
Motor power: 4 kW
Length: 2750 mm
Width: 1100 mm
Height: 1600 mm
Weight: 1540 kg
2
Metal working and machine toolsPressesEccentric presses
pressing capacity: 30 to
Tonnage rating point: 2 mm
Table length: 400 mm
Table width: 600 mm
Hole in table: 150 mm
Stroke: 1 - 60 mm
Strokes: 140 1/min
Ram guides: 4
Ram adjustment: 60 mm
Ram hole: 40 mm
Throat depth: 200 mm
Daylight: 300 mm
Motor: 3 kW
Length: 1300 mm
Width: 1150 mm
Height: 2050 mm
Weight: 1670 kg
pressing capacity: 30 to
Tonnage rating point: 2 mm
Table length: 400 mm
Table width: 600 mm
Hole in table: 150 mm
Stroke: 1 - 60 mm
Strokes: 140 1/min
Ram guides: 4
Ram adjustment: 60 mm
Ram hole: 40 mm
Throat depth: 200 mm
Daylight: 300 mm
Motor: 3 kW
Length: 1300 mm
Width: 1150 mm
Height: 2050 mm
Weight: 1670 kg
Tonnage rating point: 2 mm
Table length: 400 mm
Table width: 600 mm
Hole in table: 150 mm
Stroke: 1 - 60 mm
Strokes: 140 1/min
Ram guides: 4
Ram adjustment: 60 mm
Ram hole: 40 mm
Throat depth: 200 mm
Daylight: 300 mm
Motor: 3 kW
Length: 1300 mm
Width: 1150 mm
Height: 2050 mm
Weight: 1670 kg
9
Printing machineryLabel printing and die-cutting machine
Heidelberg SBG 56×77 cm
With safety covers
Year 1964
Heidelberg SBG 56×77 cm
With safety covers
Year 1964
With safety covers
Year 1964
_thumb.jpeg "Show advert")
_thumb.jpeg "Show advert")
_thumb.jpeg "Show advert")
10
Printing machineryPrinting machines
Heidelberg Printmaster 52-2
Year 2008
Baldwin cooling system
Double-sheet control
Easyplate
Blanked washer
Total impressions: ± 21 mil. imp.
Heidelberg Printmaster 52-2
Year 2008
Baldwin cooling system
Double-sheet control
Easyplate
Blanked washer
Total impressions: ± 21 mil. imp.
Year 2008
Baldwin cooling system
Double-sheet control
Easyplate
Blanked washer
Total impressions: ± 21 mil. imp.
-1_thumb.jpg "Show advert")
-3_thumb.jpg "Show advert")
13
Printing machineryLabel printing and die-cutting machine
Heidelberg KSB Cilinder
Format 40x57 cm
Heidelberg KSB Cilinder
Format 40x57 cm
Format 40x57 cm
-1_thumb.jpg "Show advert")
-2_thumb.jpg "Show advert")
-3_thumb.jpg "Show advert")
-4_thumb.jpg "Show advert")
-5_thumb.jpg "Show advert")
-6_thumb.jpg "Show advert")
-7_thumb.jpg "Show advert")
8
Printing machineryCutting machines
Polar Mohr 78 ED paper guillotine
Technical data:
Cutting width 780mm
Stack height 120mm
Color LCD display
Power supply 400V
Weight 1400 kg
Side tables
Chrome table surface
Spare knife, cutting sticks, tapping block, maintenance tools.
Polar Mohr 78 ED paper guillotine
Technical data:
Cutting width 780mm
Stack height 120mm
Color LCD display
Power supply 400V
Weight 1400 kg
Side tables
Chrome table surface
Spare knife, cutting sticks, tapping block, maintenance tools.
Technical data:
Cutting width 780mm
Stack height 120mm
Color LCD display
Power supply 400V
Weight 1400 kg
Side tables
Chrome table surface
Spare knife, cutting sticks, tapping block, maintenance tools.
14
Metal working and machine toolsMilling machines
X: 300 mm
Y: 160 mm
Z: 340 mm
Speed range: 40 - 2000 rpm
Mounting table: 600 x 210 mm
Taper fixture: SK 40
Control: TNC 113 Digitalanzeige
Total power: 1,5 / 1,9 kW
Weight of machine: 1050 kg
Space requirement (W x D x H): 1,2 x 1,0 x 1,9 m
Condition: good
Rigid angle table, infinitely variable feed in three axes, rapid traverse in three axes, spindle brake, vertical milling head on spindle head movable 100 mm
Accessory: machine feet, documentation, counterholder, no other accessories
X: 300 mm
Y: 160 mm
Z: 340 mm
Speed range: 40 - 2000 rpm
Mounting table: 600 x 210 mm
Taper fixture: SK 40
Control: TNC 113 Digitalanzeige
Total power: 1,5 / 1,9 kW
Weight of machine: 1050 kg
Space requirement (W x D x H): 1,2 x 1,0 x 1,9 m
Condition: good
Rigid angle table, infinitely variable feed in three axes, rapid traverse in three axes, spindle brake, vertical milling head on spindle head movable 100 mm
Accessory: machine feet, documentation, counterholder, no other accessories
Y: 160 mm
Z: 340 mm
Speed range: 40 - 2000 rpm
Mounting table: 600 x 210 mm
Taper fixture: SK 40
Control: TNC 113 Digitalanzeige
Total power: 1,5 / 1,9 kW
Weight of machine: 1050 kg
Space requirement (W x D x H): 1,2 x 1,0 x 1,9 m
Condition: good
Rigid angle table, infinitely variable feed in three axes, rapid traverse in three axes, spindle brake, vertical milling head on spindle head movable 100 mm
Accessory: machine feet, documentation, counterholder, no other accessories
10
Metal working and machine toolsMachining centersMachining centers horizontal
x-travel: 1250 mm
y-travel: 910 mm
z-travel: 875 mm
Control: Siemens
Type: 840 D
Pallet size: 800x800 mm
Number of pallets: 2
Speed: 16.5 rpm
Gear stages: 2
Feed: 1-32000 mm/min
Rotary table: 360x1 °
Table load: 1150 kg
Spindle mount ISO: 50
Tool changer: 165 positions.
Total power requirement: kW
Machine weight approx.: 18.5 t
Space requirement approx.: m
x-travel: 1250 mm
y-travel: 910 mm
z-travel: 875 mm
Control: Siemens
Type: 840 D
Pallet size: 800x800 mm
Number of pallets: 2
Speed: 16.5 rpm
Gear stages: 2
Feed: 1-32000 mm/min
Rotary table: 360x1 °
Table load: 1150 kg
Spindle mount ISO: 50
Tool changer: 165 positions.
Total power requirement: kW
Machine weight approx.: 18.5 t
Space requirement approx.: m
y-travel: 910 mm
z-travel: 875 mm
Control: Siemens
Type: 840 D
Pallet size: 800x800 mm
Number of pallets: 2
Speed: 16.5 rpm
Gear stages: 2
Feed: 1-32000 mm/min
Rotary table: 360x1 °
Table load: 1150 kg
Spindle mount ISO: 50
Tool changer: 165 positions.
Total power requirement: kW
Machine weight approx.: 18.5 t
Space requirement approx.: m
4
Food machinesBakery-, pastry equipmentCutting machines
John Hunt Medium Champion Pie press, Single station pie press, tabletop, tooling diameter 180mm, tooling depth 35mm, manual press
John Hunt Medium Champion Pie press, Single station pie press, tabletop, tooling diameter 180mm, tooling depth 35mm, manual press
4
Food machinesMeat processing
NNP Twin sink, Stainless, twin sink unit, top mounted tap, twin bottom drainage
NNP Twin sink, Stainless, twin sink unit, top mounted tap, twin bottom drainage
4
Food machinesMeat processing
Syspal Sink, Stainless, four station sink, knee operated
Syspal Sink, Stainless, four station sink, knee operated
9
Metal working and machine toolsLathes
Swing over bed: 600 mm
Distance between centers: 2000 mm
Centre height: 300 mm
Spindle bore: 80 mm
swing over cross slide: 400 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 8
Spindle taper: 90 M
Spindle speed steps: 21
Spindle revs: 20 - 2000 rpm
Number of feeds: 120
Longitudinal feed range: 0.04 - 12 mm/r
Cross feed range: 0.02 - 6 mm/r
Number of threads: 64
Metric thread range: 0.5 - 120 mm
Inch thread range: 60 - 1/4 Tpi
Module thread range: 0.125 - 30
Cross slide travel: 315 mm
Top slide travel: 130 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 230 mm
Motor power: 7.5 kW
Length: 3600 mm
Width: 1250 mm
Height: 1400 mm
Weight: 3110 kg
Swing over bed: 600 mm
Distance between centers: 2000 mm
Centre height: 300 mm
Spindle bore: 80 mm
swing over cross slide: 400 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 8
Spindle taper: 90 M
Spindle speed steps: 21
Spindle revs: 20 - 2000 rpm
Number of feeds: 120
Longitudinal feed range: 0.04 - 12 mm/r
Cross feed range: 0.02 - 6 mm/r
Number of threads: 64
Metric thread range: 0.5 - 120 mm
Inch thread range: 60 - 1/4 Tpi
Module thread range: 0.125 - 30
Cross slide travel: 315 mm
Top slide travel: 130 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 230 mm
Motor power: 7.5 kW
Length: 3600 mm
Width: 1250 mm
Height: 1400 mm
Weight: 3110 kg
Distance between centers: 2000 mm
Centre height: 300 mm
Spindle bore: 80 mm
swing over cross slide: 400 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 8
Spindle taper: 90 M
Spindle speed steps: 21
Spindle revs: 20 - 2000 rpm
Number of feeds: 120
Longitudinal feed range: 0.04 - 12 mm/r
Cross feed range: 0.02 - 6 mm/r
Number of threads: 64
Metric thread range: 0.5 - 120 mm
Inch thread range: 60 - 1/4 Tpi
Module thread range: 0.125 - 30
Cross slide travel: 315 mm
Top slide travel: 130 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 230 mm
Motor power: 7.5 kW
Length: 3600 mm
Width: 1250 mm
Height: 1400 mm
Weight: 3110 kg
13
Metal working and machine toolsLathes
Swing over bed: 600 mm
Distance between centers: 1500 mm
Centre height: 300 mm
Spindle bore: 80 mm
swing over cross slide: 400 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 8
Spindle taper: 90 M
Revs continuous variable in gear steps: 3
Revs continuous variable: 20 - 100, 80 - 400, 400 - 2000 rpm
Longitudinal feed range: max. 8 m/min
Cross feed range: max. 8 m/min
Cross slide travel: 290 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 225 mm
Motor power: 11 kW
Z-axis servo drive: 3,5 / 22 kW/Nm
X-axis servo drive: 1,75 / 11 kW/Nm
Spindle max. torque: 120 Nm
Tow strength Z-axis: 1250 daN
Tow strength X-axis: 1050 daN
Swing over bed: 600 mm
Distance between centers: 1500 mm
Centre height: 300 mm
Spindle bore: 80 mm
swing over cross slide: 400 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 8
Spindle taper: 90 M
Revs continuous variable in gear steps: 3
Revs continuous variable: 20 - 100, 80 - 400, 400 - 2000 rpm
Longitudinal feed range: max. 8 m/min
Cross feed range: max. 8 m/min
Cross slide travel: 290 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 225 mm
Motor power: 11 kW
Z-axis servo drive: 3,5 / 22 kW/Nm
X-axis servo drive: 1,75 / 11 kW/Nm
Spindle max. torque: 120 Nm
Tow strength Z-axis: 1250 daN
Tow strength X-axis: 1050 daN
Distance between centers: 1500 mm
Centre height: 300 mm
Spindle bore: 80 mm
swing over cross slide: 400 mm
Width of bed: 400 mm
Spindle nose / DIN55027: 8
Spindle taper: 90 M
Revs continuous variable in gear steps: 3
Revs continuous variable: 20 - 100, 80 - 400, 400 - 2000 rpm
Longitudinal feed range: max. 8 m/min
Cross feed range: max. 8 m/min
Cross slide travel: 290 mm
Tailstock quill diameter: 90 mm
Tailstock quill taper: 5 MK
Tailstock travel: 225 mm
Motor power: 11 kW
Z-axis servo drive: 3,5 / 22 kW/Nm
X-axis servo drive: 1,75 / 11 kW/Nm
Spindle max. torque: 120 Nm
Tow strength Z-axis: 1250 daN
Tow strength X-axis: 1050 daN
11
Metal working and machine toolsMachining centersMachining centers horizontal
x-travel: 3200 mm
y-travel: 1400 mm
z-travel: 508 mm
Table surface: 3000x1250 mm
Stand passage: 1500 mm
Speed: 35-5000 rpm
Spindle mount ISO: 50
Control: Mazatron M Plus
Table load: 5000 kg
Tool changer: 30
x-travel: 3200 mm
y-travel: 1400 mm
z-travel: 508 mm
Table surface: 3000x1250 mm
Stand passage: 1500 mm
Speed: 35-5000 rpm
Spindle mount ISO: 50
Control: Mazatron M Plus
Table load: 5000 kg
Tool changer: 30
y-travel: 1400 mm
z-travel: 508 mm
Table surface: 3000x1250 mm
Stand passage: 1500 mm
Speed: 35-5000 rpm
Spindle mount ISO: 50
Control: Mazatron M Plus
Table load: 5000 kg
Tool changer: 30
8
Food machinesBakery-, pastry equipmentMixers
Glass VSM150 Mixer, 150Kg glass mixer, tilting for discharge, stainless lid, with vac pump, For marinating and massaging the meat and mixing of liquid, semi-solid and powdery products, mobile, 3Ph
Glass VSM150 Mixer, 150Kg glass mixer, tilting for discharge, stainless lid, with vac pump, For marinating and massaging the meat and mixing of liquid, semi-solid and powdery products, mobile, 3Ph
11
Metal working and machine toolsLathesLathes
Face plate diameter: 3500 mm
Swing diameter: 4000 mm
Turning height: 3150 mm
Support adjustment: 1700 mm
Table load: 25 t
Speed: rpm
Feed: mm/rev
Digital display: Heidenhain
Support: 2
Total power requirement: 90 kW
Machine weight approx.: 95 t
Space requirement approx.: m
Face plate diameter: 3500 mm
Swing diameter: 4000 mm
Turning height: 3150 mm
Support adjustment: 1700 mm
Table load: 25 t
Speed: rpm
Feed: mm/rev
Digital display: Heidenhain
Support: 2
Total power requirement: 90 kW
Machine weight approx.: 95 t
Space requirement approx.: m
Swing diameter: 4000 mm
Turning height: 3150 mm
Support adjustment: 1700 mm
Table load: 25 t
Speed: rpm
Feed: mm/rev
Digital display: Heidenhain
Support: 2
Total power requirement: 90 kW
Machine weight approx.: 95 t
Space requirement approx.: m
10
Metal working and machine toolsDrilling machines and boring millsJig boring machines
Spindle diameter: 120mm
x-travel: 1200 mm
y-travel: 600 mm
z-travel: 600 mm
Speed: 19-1900 rpm
Table size: 600x1200 mm
Table load: 2000 kg
Spindle mount ISO: 50
Feed: 0.042-1.46 mm/rev
Machine weight approx.: . t
Space requirement approx.: . m
Spindle diameter: 120mm
x-travel: 1200 mm
y-travel: 600 mm
z-travel: 600 mm
Speed: 19-1900 rpm
Table size: 600x1200 mm
Table load: 2000 kg
Spindle mount ISO: 50
Feed: 0.042-1.46 mm/rev
Machine weight approx.: . t
Space requirement approx.: . m
x-travel: 1200 mm
y-travel: 600 mm
z-travel: 600 mm
Speed: 19-1900 rpm
Table size: 600x1200 mm
Table load: 2000 kg
Spindle mount ISO: 50
Feed: 0.042-1.46 mm/rev
Machine weight approx.: . t
Space requirement approx.: . m
10
Food machinesOther
Serial: SD150P5311297 Stainless, variable speed, height adjustable frame, 50l capacity mesh guarded hopper, roller conveyor at discharge point, comes with two different styles of nozzles, foot pedal, with manual
Serial: SD150P5311297 Stainless, variable speed, height adjustable frame, 50l capacity mesh guarded hopper, roller conveyor at discharge point, comes with two different styles of nozzles, foot pedal, with manual
5
Printing machineryPost press machinesOther
Heidelberg GTP Hot Foil
size 34×46
with Hotfoil
Heidelberg GTP Hot Foil
size 34×46
with Hotfoil
size 34×46
with Hotfoil
 Grey cilinder-1_thumb.jpg "Show advert")
 Grey cilinder-3_thumb.jpg "Show advert")
 Grey cilinder-4_thumb.jpg "Show advert")
 Grey cilinder-5_thumb.jpg "Show advert")
 Grey cilinder-6_thumb.jpg "Show advert")
 Grey cilinder-7_thumb.jpg "Show advert")
 Grey cilinder-8_thumb.jpg "Show advert")
 Grey cilinder-9_thumb.jpg "Show advert")
 Grey cilinder-91_thumb.jpg "Show advert")
10
Printing machineryPost press machinesDie cutter
Heidelberg SBB ( 56×82 cm) Gray cylinder
Very nice Heidelberg SBB cylinder
Fitted with safety covers with switches.
Electronics renewed.
Complete with 2 punch frames
Heidelberg SBB ( 56×82 cm) Gray cylinder
Very nice Heidelberg SBB cylinder
Fitted with safety covers with switches.
Electronics renewed.
Complete with 2 punch frames
5
Printing machineryOther
Heidelberg GTP orignal hotfoil platen
Heidelberg GTP orignal hotfoil platen
9
Food machinesMeat processing
Frampton FR1-3 Flash roaster, Stainless flash roaster, used when pre cooked meats need to have a roast finish, allows products such as hams to be roasted in under 3mins and still cool enough to be packed, ideal for meats, fish, veg and more, belt dimensions 2100mm x 140mm, variable speed, adjustable temp control, mobile, 3Ph
Frampton FR1-3 Flash roaster, Stainless flash roaster, used when pre cooked meats need to have a roast finish, allows products such as hams to be roasted in under 3mins and still cool enough to be packed, ideal for meats, fish, veg and more, belt dimensions 2100mm x 140mm, variable speed, adjustable temp control, mobile, 3Ph
6
Food machinesPackaging machinery
Turbovac TV5575 Dip tank Serial: 20151529 2015, stainless dip tank, shrink tank, platform dimensions 730mm x 535mm, dipping length 300mm, max product height 250mm, max water capacity 130l, max product weight 30Kgs, adjustable temp control, exhaust hood, with outfeed conveyor, mobile, 3Ph
Turbovac TV5575 Dip tank Serial: 20151529 2015, stainless dip tank, shrink tank, platform dimensions 730mm x 535mm, dipping length 300mm, max product height 250mm, max water capacity 130l, max product weight 30Kgs, adjustable temp control, exhaust hood, with outfeed conveyor, mobile, 3Ph
8
Food machinesPackaging machinery
2011, stainless tray sealer, modified atmosphere or seal only, up to 10 trays per min, seals two tray at a time, tray dims 200mm x 160mm, adjustable temp and timer controls, 3Ph
2011, stainless tray sealer, modified atmosphere or seal only, up to 10 trays per min, seals two tray at a time, tray dims 200mm x 160mm, adjustable temp and timer controls, 3Ph
4
Metal working and machine toolsSheet metal working machinesPress brakes
pressing capacity: 600 to
Bending length: 4050 mm
Axes: Y1 / Y2 / X und R Achse
Stroke: 365 mm
Inside distance between side frames: 3100 mm
Gap in side frame: 410 mm
Daylight: 700 mm
Power concept: hydraulic
rapid speed Y-axis: 160 mm/s
Working speed Y-axis: 10
Retractionspeed Y-axis: 160
Back gauge travel X-axis: 650 mm
Back gauge speed X-axis: 500
Back gauge travel R-axis: 250 mm
Table height: 900 mm
Table width: 154 mm
Oiltank: 280 l
Motor power: 2 x 11 kW
Length: 5750 mm
Width: 2500 mm
Height: 4000 mm
Weight: 40500 kg
pressing capacity: 600 to
Bending length: 4050 mm
Axes: Y1 / Y2 / X und R Achse
Stroke: 365 mm
Inside distance between side frames: 3100 mm
Gap in side frame: 410 mm
Daylight: 700 mm
Power concept: hydraulic
rapid speed Y-axis: 160 mm/s
Working speed Y-axis: 10
Retractionspeed Y-axis: 160
Back gauge travel X-axis: 650 mm
Back gauge speed X-axis: 500
Back gauge travel R-axis: 250 mm
Table height: 900 mm
Table width: 154 mm
Oiltank: 280 l
Motor power: 2 x 11 kW
Length: 5750 mm
Width: 2500 mm
Height: 4000 mm
Weight: 40500 kg
Bending length: 4050 mm
Axes: Y1 / Y2 / X und R Achse
Stroke: 365 mm
Inside distance between side frames: 3100 mm
Gap in side frame: 410 mm
Daylight: 700 mm
Power concept: hydraulic
rapid speed Y-axis: 160 mm/s
Working speed Y-axis: 10
Retractionspeed Y-axis: 160
Back gauge travel X-axis: 650 mm
Back gauge speed X-axis: 500
Back gauge travel R-axis: 250 mm
Table height: 900 mm
Table width: 154 mm
Oiltank: 280 l
Motor power: 2 x 11 kW
Length: 5750 mm
Width: 2500 mm
Height: 4000 mm
Weight: 40500 kg
10
Metal working and machine toolsMilling machinesTravelling column milling machines
x-travel: 3500 mm
y-travel: 1600 mm
z-travel: 900 mm
Speed: 20-2000 rpm
Spindle mount ISO: SK50
Table dimension: 5000x1000 mm
Control: Heidenhain TNC 426
Spindle drive motor: 22 kW
Rapid traverse: 5000 mm/min
Machine weight approx.: 16 t
x-travel: 3500 mm
y-travel: 1600 mm
z-travel: 900 mm
Speed: 20-2000 rpm
Spindle mount ISO: SK50
Table dimension: 5000x1000 mm
Control: Heidenhain TNC 426
Spindle drive motor: 22 kW
Rapid traverse: 5000 mm/min
Machine weight approx.: 16 t
y-travel: 1600 mm
z-travel: 900 mm
Speed: 20-2000 rpm
Spindle mount ISO: SK50
Table dimension: 5000x1000 mm
Control: Heidenhain TNC 426
Spindle drive motor: 22 kW
Rapid traverse: 5000 mm/min
Machine weight approx.: 16 t
_thumb.jpg "Show advert")
_thumb.jpg "Show advert")
10
Printing machineryPost press machinesLaminating machines
Stock LM 123
A simple semi-automatic spot labeling machine suitable for running (labeling) substrate sheets, flat boxes, blanks, as well as pre-folded (RSC´s) with litho printed labels. Equipped with an automatic label feeder and take-off table. The label is mounted to the lower side of the substrate sheet.
Label Feeder (4E): Suction feeder, for automatically feeding of the labels. The labels have to be pre-loaded on the pile board by hand. Pre-loading height: approx. 7.8”. On sheet removal the pile is re-timing automatically. A suction bar is separating the labels at their front edge, always sucking a single sheet and transporting it into the machine.
Label Registering Unit (LM-1) includes a timed suction conveyor that incorporates a separate motor drive that takes the glued labels after leaving the gluing unit and automatically registers the labels. Precise registration is achieved utilizing the unit’s adjustable side and rear edge guides that are set to the dimensions required for the proper registration of the corrugated sheet or box.
A 2-cylinder gluing unit is utilized for glue application and metering roller with stripping needles. The glue is applied to the label that is then stripped off the application roller by special stripping needles. The litho printed label will always be glued. The Model LM includes an automatic glue-feeding system with diaphragm pump (P).
Squeeze roller that presses the labelled sheets and blanks together.
Integrated sensor for detecting and registering the glued label
Label registering unit for placing and applying the corrugated blank to the glued label
Manual feeding of the corrugated blank or box pressure roller
Take-off table for the manual take-off of the labeled sheets / blanks.
Integrated sheet counter.
Siemens PLC control.
Suction belt
Stock LM 123
A simple semi-automatic spot labeling machine suitable for running (labeling) substrate sheets, flat boxes, blanks, as well as pre-folded (RSC´s) with litho printed labels. Equipped with an automatic label feeder and take-off table. The label is mounted to the lower side of the substrate sheet.
Label Feeder (4E): Suction feeder, for automatically feeding of the labels. The labels have to be pre-loaded on the pile board by hand. Pre-loading height: approx. 7.8”. On sheet removal the pile is re-timing automatically. A suction bar is separating the labels at their front edge, always sucking a single sheet and transporting it into the machine.
Label Registering Unit (LM-1) includes a timed suction conveyor that incorporates a separate motor drive that takes the glued labels after leaving the gluing unit and automatically registers the labels. Precise registration is achieved utilizing the unit’s adjustable side and rear edge guides that are set to the dimensions required for the proper registration of the corrugated sheet or box.
A 2-cylinder gluing unit is utilized for glue application and metering roller with stripping needles. The glue is applied to the label that is then stripped off the application roller by special stripping needles. The litho printed label will always be glued. The Model LM includes an automatic glue-feeding system with diaphragm pump (P).
Squeeze roller that presses the labelled sheets and blanks together.
Integrated sensor for detecting and registering the glued label
Label registering unit for placing and applying the corrugated blank to the glued label
Manual feeding of the corrugated blank or box pressure roller
Take-off table for the manual take-off of the labeled sheets / blanks.
Integrated sheet counter.
Siemens PLC control.
Suction belt
A simple semi-automatic spot labeling machine suitable for running (labeling) substrate sheets, flat boxes, blanks, as well as pre-folded (RSC´s) with litho printed labels. Equipped with an automatic label feeder and take-off table. The label is mounted to the lower side of the substrate sheet.
Label Feeder (4E): Suction feeder, for automatically feeding of the labels. The labels have to be pre-loaded on the pile board by hand. Pre-loading height: approx. 7.8”. On sheet removal the pile is re-timing automatically. A suction bar is separating the labels at their front edge, always sucking a single sheet and transporting it into the machine.
Label Registering Unit (LM-1) includes a timed suction conveyor that incorporates a separate motor drive that takes the glued labels after leaving the gluing unit and automatically registers the labels. Precise registration is achieved utilizing the unit’s adjustable side and rear edge guides that are set to the dimensions required for the proper registration of the corrugated sheet or box.
A 2-cylinder gluing unit is utilized for glue application and metering roller with stripping needles. The glue is applied to the label that is then stripped off the application roller by special stripping needles. The litho printed label will always be glued. The Model LM includes an automatic glue-feeding system with diaphragm pump (P).
Squeeze roller that presses the labelled sheets and blanks together.
Integrated sensor for detecting and registering the glued label
Label registering unit for placing and applying the corrugated blank to the glued label
Manual feeding of the corrugated blank or box pressure roller
Take-off table for the manual take-off of the labeled sheets / blanks.
Integrated sheet counter.
Siemens PLC control.
Suction belt
4
Printing machineryPrinting machines
Heidelberg GTP hot foil platen.
Serial GTP 63613
Complete with big hot foil chase
Heidelberg GTP hot foil platen.
Serial GTP 63613
Complete with big hot foil chase
Serial GTP 63613
Complete with big hot foil chase
7
Food machinesAccessories and spare parts
Top labeller, Stainless, top labelling machine, belt dimensions 1500mm x 90mm, max label width 90mm, height adjustable labelling frame, HMI touch screen control, 1Ph
Top labeller, Stainless, top labelling machine, belt dimensions 1500mm x 90mm, max label width 90mm, height adjustable labelling frame, HMI touch screen control, 1Ph
7
Metal working and machine toolsLathes
Swing over bed: 400 mm
Distance between centers: 1000 mm
Centre height: 200 mm
Spindle bore: 52 mm
swing over cross slide: 235 mm
Width of bed: 320 mm
Spindle nose / DIN55027: 6
Spindle taper: 6 M
Spindle speed steps: 12
Spindle revs: 50–2.240 rpm
Number of feeds: 80
Longitudinal feed range: 0.015 - 0.6 mm/r
Cross feed range: 0.0075 - 0.3 mm/r
Number of threads: 40
Metric thread range: 0.25 - 7.5 mm
Inch thread range: 120 - 4 Tpi
Module thread range: 0.0625 - 1.875
DP thread range: Array
Cross slide travel: 235 mm
Top slide travel: 110 mm
Tailstock quill diameter: 50 mm
Tailstock quill taper: 4 MK
Tailstock travel: 100 mm
Motor power: 4 kW
Length: 2750 mm
Width: 1100 mm
Height: 1600 mm
Weight: 1540 kg
Swing over bed: 400 mm
Distance between centers: 1000 mm
Centre height: 200 mm
Spindle bore: 52 mm
swing over cross slide: 235 mm
Width of bed: 320 mm
Spindle nose / DIN55027: 6
Spindle taper: 6 M
Spindle speed steps: 12
Spindle revs: 50–2.240 rpm
Number of feeds: 80
Longitudinal feed range: 0.015 - 0.6 mm/r
Cross feed range: 0.0075 - 0.3 mm/r
Number of threads: 40
Metric thread range: 0.25 - 7.5 mm
Inch thread range: 120 - 4 Tpi
Module thread range: 0.0625 - 1.875
DP thread range: Array
Cross slide travel: 235 mm
Top slide travel: 110 mm
Tailstock quill diameter: 50 mm
Tailstock quill taper: 4 MK
Tailstock travel: 100 mm
Motor power: 4 kW
Length: 2750 mm
Width: 1100 mm
Height: 1600 mm
Weight: 1540 kg
Distance between centers: 1000 mm
Centre height: 200 mm
Spindle bore: 52 mm
swing over cross slide: 235 mm
Width of bed: 320 mm
Spindle nose / DIN55027: 6
Spindle taper: 6 M
Spindle speed steps: 12
Spindle revs: 50–2.240 rpm
Number of feeds: 80
Longitudinal feed range: 0.015 - 0.6 mm/r
Cross feed range: 0.0075 - 0.3 mm/r
Number of threads: 40
Metric thread range: 0.25 - 7.5 mm
Inch thread range: 120 - 4 Tpi
Module thread range: 0.0625 - 1.875
DP thread range: Array
Cross slide travel: 235 mm
Top slide travel: 110 mm
Tailstock quill diameter: 50 mm
Tailstock quill taper: 4 MK
Tailstock travel: 100 mm
Motor power: 4 kW
Length: 2750 mm
Width: 1100 mm
Height: 1600 mm
Weight: 1540 kg
8
Metal working and machine toolsLathes
Swing over bed: 335 mm
Distance between centers: 750 mm
Centre height: 165 mm
Spindle bore: 42 mm
swing over cross slide: 175 mm
Width of bed: 250 mm
Spindle nose / DIN55027: DIN55022-5 Nr. 4
Spindle revs: 60-2000 (9) rpm
Longitudinal feed range: 0.05 - 0.75 mm/r
Cross feed range: 0.025 - 0.375 mm/r
Metric thread range: 0.5 - 7.5 mm
Module thread range: 60
Cross slide travel: 245 mm
Top slide travel: 120 mm
Tailstock quill diameter: 48 mm
Tailstock quill taper: 3 MK
Tailstock travel: 140 mm
Motor power: 2.2 kW
Length: 1800 mm
Width: 850 mm
Height: 1485 mm
Weight: 880 kg
Swing over bed: 335 mm
Distance between centers: 750 mm
Centre height: 165 mm
Spindle bore: 42 mm
swing over cross slide: 175 mm
Width of bed: 250 mm
Spindle nose / DIN55027: DIN55022-5 Nr. 4
Spindle revs: 60-2000 (9) rpm
Longitudinal feed range: 0.05 - 0.75 mm/r
Cross feed range: 0.025 - 0.375 mm/r
Metric thread range: 0.5 - 7.5 mm
Module thread range: 60
Cross slide travel: 245 mm
Top slide travel: 120 mm
Tailstock quill diameter: 48 mm
Tailstock quill taper: 3 MK
Tailstock travel: 140 mm
Motor power: 2.2 kW
Length: 1800 mm
Width: 850 mm
Height: 1485 mm
Weight: 880 kg
Distance between centers: 750 mm
Centre height: 165 mm
Spindle bore: 42 mm
swing over cross slide: 175 mm
Width of bed: 250 mm
Spindle nose / DIN55027: DIN55022-5 Nr. 4
Spindle revs: 60-2000 (9) rpm
Longitudinal feed range: 0.05 - 0.75 mm/r
Cross feed range: 0.025 - 0.375 mm/r
Metric thread range: 0.5 - 7.5 mm
Module thread range: 60
Cross slide travel: 245 mm
Top slide travel: 120 mm
Tailstock quill diameter: 48 mm
Tailstock quill taper: 3 MK
Tailstock travel: 140 mm
Motor power: 2.2 kW
Length: 1800 mm
Width: 850 mm
Height: 1485 mm
Weight: 880 kg
1
Metal working and machine toolsAccessories and spare partsOther
Working height: 820 - 940 mm
Maximal table load: 900 kg
Max. load per meter: 300 kg/m
width of rolls: 350 mm
diameter of rolls: 60 x 2 mm
axis diameter: 15 mm
max. gauge length: 2550 mm
roll gapping: 250 mm
Length: 3000 mm
Working height: 820 - 940 mm
Maximal table load: 900 kg
Max. load per meter: 300 kg/m
width of rolls: 350 mm
diameter of rolls: 60 x 2 mm
axis diameter: 15 mm
max. gauge length: 2550 mm
roll gapping: 250 mm
Length: 3000 mm
Maximal table load: 900 kg
Max. load per meter: 300 kg/m
width of rolls: 350 mm
diameter of rolls: 60 x 2 mm
axis diameter: 15 mm
max. gauge length: 2550 mm
roll gapping: 250 mm
Length: 3000 mm
1
Metal working and machine toolsAccessories and spare partsOther
Working height: 820 - 940 mm
Maximal table load: 900 kg
Max. load per meter: 300 kg/m
width of rolls: 350 mm
diameter of rolls: 60 x 2 mm
axis diameter: 15 mm
max. gauge length: 2550 mm
roll gapping: 250 mm
Length: 3000 mm
Working height: 820 - 940 mm
Maximal table load: 900 kg
Max. load per meter: 300 kg/m
width of rolls: 350 mm
diameter of rolls: 60 x 2 mm
axis diameter: 15 mm
max. gauge length: 2550 mm
roll gapping: 250 mm
Length: 3000 mm
Maximal table load: 900 kg
Max. load per meter: 300 kg/m
width of rolls: 350 mm
diameter of rolls: 60 x 2 mm
axis diameter: 15 mm
max. gauge length: 2550 mm
roll gapping: 250 mm
Length: 3000 mm
2
Metal working and machine toolsPressesEccentric presses
pressing capacity: 160 to
Tonnage rating point: 6 mm
Table length: 750 mm
Table width: 1100 mm
Hole in table: 230 mm
Stroke: 1 - 172 mm
Strokes: 45 1/min
Ram guides: 6
Ram adjustment: 100 mm
Ram hole: 80 mm
Throat depth: 375 mm
Daylight: 540 mm
Motor: 11 kW
Length: 1890 mm
Width: 1950 mm
Height: 3650 mm
Weight: 15500 kg
pressing capacity: 160 to
Tonnage rating point: 6 mm
Table length: 750 mm
Table width: 1100 mm
Hole in table: 230 mm
Stroke: 1 - 172 mm
Strokes: 45 1/min
Ram guides: 6
Ram adjustment: 100 mm
Ram hole: 80 mm
Throat depth: 375 mm
Daylight: 540 mm
Motor: 11 kW
Length: 1890 mm
Width: 1950 mm
Height: 3650 mm
Weight: 15500 kg
Tonnage rating point: 6 mm
Table length: 750 mm
Table width: 1100 mm
Hole in table: 230 mm
Stroke: 1 - 172 mm
Strokes: 45 1/min
Ram guides: 6
Ram adjustment: 100 mm
Ram hole: 80 mm
Throat depth: 375 mm
Daylight: 540 mm
Motor: 11 kW
Length: 1890 mm
Width: 1950 mm
Height: 3650 mm
Weight: 15500 kg
2
Metal working and machine toolsPressesEccentric presses
pressing capacity: 130 to
Tonnage rating point: 4.5 mm
Table length: 650 mm
Table width: 950 mm
Hole in table: 220 mm
Stroke: 1 - 132 mm
Strokes: 50 1/min
Ram guides: 6
Ram adjustment: 95 mm
Ram hole: 70 mm
Throat depth: 325 mm
Daylight: 500 mm
Motor: 11 kW
Length: 1800 mm
Width: 1725 mm
Height: 3020 mm
Weight: 8000 kg
pressing capacity: 130 to
Tonnage rating point: 4.5 mm
Table length: 650 mm
Table width: 950 mm
Hole in table: 220 mm
Stroke: 1 - 132 mm
Strokes: 50 1/min
Ram guides: 6
Ram adjustment: 95 mm
Ram hole: 70 mm
Throat depth: 325 mm
Daylight: 500 mm
Motor: 11 kW
Length: 1800 mm
Width: 1725 mm
Height: 3020 mm
Weight: 8000 kg
Tonnage rating point: 4.5 mm
Table length: 650 mm
Table width: 950 mm
Hole in table: 220 mm
Stroke: 1 - 132 mm
Strokes: 50 1/min
Ram guides: 6
Ram adjustment: 95 mm
Ram hole: 70 mm
Throat depth: 325 mm
Daylight: 500 mm
Motor: 11 kW
Length: 1800 mm
Width: 1725 mm
Height: 3020 mm
Weight: 8000 kg
9
Metal working and machine toolsPressesEccentric presses
pressing capacity: 100 to
Tonnage rating point: 4.5 mm
Table length: 700 mm
Table width: 1000 mm
Hole in table: 210 mm
Stroke: 1 - 132 mm
Strokes: 58 1/min
Ram guides: 6
Ram adjustment: 90 mm
Ram hole: 60 mm
Throat depth: 300 mm
Daylight: 445 mm
Motor: 7.5 kW
Length: 1650 mm
Width: 1545 mm
Height: 3011 mm
Weight: 7000 kg
pressing capacity: 100 to
Tonnage rating point: 4.5 mm
Table length: 700 mm
Table width: 1000 mm
Hole in table: 210 mm
Stroke: 1 - 132 mm
Strokes: 58 1/min
Ram guides: 6
Ram adjustment: 90 mm
Ram hole: 60 mm
Throat depth: 300 mm
Daylight: 445 mm
Motor: 7.5 kW
Length: 1650 mm
Width: 1545 mm
Height: 3011 mm
Weight: 7000 kg
Tonnage rating point: 4.5 mm
Table length: 700 mm
Table width: 1000 mm
Hole in table: 210 mm
Stroke: 1 - 132 mm
Strokes: 58 1/min
Ram guides: 6
Ram adjustment: 90 mm
Ram hole: 60 mm
Throat depth: 300 mm
Daylight: 445 mm
Motor: 7.5 kW
Length: 1650 mm
Width: 1545 mm
Height: 3011 mm
Weight: 7000 kg
3
Metal working and machine toolsSheet metal working machinesPipe-bending machines
Flexion modulus: 170 cm³
Standard steel tube: 150 x 9 mm
Gas tube: 6" x 7,11 mm
Furniture tube: 150 x 9 mm
FE35 (for hydraulic tubes): 168,3 x 8,5 mm
Stainless steel AISI304-318: 141,3 x 6,55 mm
Stainless steel AISI308 (food industry): 141,3 x 6,55 mm
Brass soft: 168,3 x 9 mm
Hard copper and aluminium: 168,3 x 9 mm
Soft copper: 168,3 x 9 mm
Conduit tube (TAZ): 141,3 x 8 mm
Mepla, Gebereit and similar: 150 x 6 mm
Roundbar solid (S275JO): 110 mm
Squarebar solid (S275JO): 90 x 90 mm
Flatsteel solid (S275JO): 120 x 60 mm
Square profile (S275JO): 140 x 70 x 12 bzw. 140 x 140 x 6 mm
T-profile (S275JO): 120 x 120 x 10 mm
U-profile (S275JO): 120 x 120 x 8 mm
Max. bending radius: 800 mm
Min. bending radius: 100 mm
Min. tube Ø: 10 mm
Max. bending speed: 1 r/min
Motor: 15 kW
Length: 1000 mm
Width: 1900 mm
Height: 1475 mm
Weight: 2700 kg
Flexion modulus: 170 cm³
Standard steel tube: 150 x 9 mm
Gas tube: 6" x 7,11 mm
Furniture tube: 150 x 9 mm
FE35 (for hydraulic tubes): 168,3 x 8,5 mm
Stainless steel AISI304-318: 141,3 x 6,55 mm
Stainless steel AISI308 (food industry): 141,3 x 6,55 mm
Brass soft: 168,3 x 9 mm
Hard copper and aluminium: 168,3 x 9 mm
Soft copper: 168,3 x 9 mm
Conduit tube (TAZ): 141,3 x 8 mm
Mepla, Gebereit and similar: 150 x 6 mm
Roundbar solid (S275JO): 110 mm
Squarebar solid (S275JO): 90 x 90 mm
Flatsteel solid (S275JO): 120 x 60 mm
Square profile (S275JO): 140 x 70 x 12 bzw. 140 x 140 x 6 mm
T-profile (S275JO): 120 x 120 x 10 mm
U-profile (S275JO): 120 x 120 x 8 mm
Max. bending radius: 800 mm
Min. bending radius: 100 mm
Min. tube Ø: 10 mm
Max. bending speed: 1 r/min
Motor: 15 kW
Length: 1000 mm
Width: 1900 mm
Height: 1475 mm
Weight: 2700 kg
Standard steel tube: 150 x 9 mm
Gas tube: 6" x 7,11 mm
Furniture tube: 150 x 9 mm
FE35 (for hydraulic tubes): 168,3 x 8,5 mm
Stainless steel AISI304-318: 141,3 x 6,55 mm
Stainless steel AISI308 (food industry): 141,3 x 6,55 mm
Brass soft: 168,3 x 9 mm
Hard copper and aluminium: 168,3 x 9 mm
Soft copper: 168,3 x 9 mm
Conduit tube (TAZ): 141,3 x 8 mm
Mepla, Gebereit and similar: 150 x 6 mm
Roundbar solid (S275JO): 110 mm
Squarebar solid (S275JO): 90 x 90 mm
Flatsteel solid (S275JO): 120 x 60 mm
Square profile (S275JO): 140 x 70 x 12 bzw. 140 x 140 x 6 mm
T-profile (S275JO): 120 x 120 x 10 mm
U-profile (S275JO): 120 x 120 x 8 mm
Max. bending radius: 800 mm
Min. bending radius: 100 mm
Min. tube Ø: 10 mm
Max. bending speed: 1 r/min
Motor: 15 kW
Length: 1000 mm
Width: 1900 mm
Height: 1475 mm
Weight: 2700 kg
2
Metal working and machine toolsSheet metal working machinesPipe-bending machines
Flexion modulus: 80 cm³
Standard steel tube: 127 x 7,1 mm
Gas tube: 4" x 8,56 mm
Furniture tube: 127 x 7,1 mm
FE35 (for hydraulic tubes): 100 x 11 mm
Stainless steel AISI304-318: 114,3 x 5,6 mm
Stainless steel AISI308 (food industry): 114,3 x 5,6 mm
Brass soft: 139,7 x 8,8 mm
Hard copper and aluminium: 139,7 x 8,8 mm
Soft copper: 139,7 x 8,8 mm
Conduit tube (TAZ): 120 x 9 mm
Mepla, Gebereit and similar: 120 x 6.5 mm
Roundbar solid (S275JO): 90 mm
Squarebar solid (S275JO): 75 x 75 mm
Flatsteel solid (S275JO): 100 x 50 mm
Square profile (S275JO): 120 x 60 x 9 bzw. 90 x 90 x 10 mm
T-profile (S275JO): 100 x 100 x 10 mm
U-profile (S275JO): 100 x 100 x 10 mm
Max. bending radius: 700 mm
Min. bending radius: 36 mm
Min. tube Ø: 10 mm
Max. bending speed: 0 - 0,75 r/min
Motor: 3.5 kW
Length: 850 mm
Width: 1200 mm
Height: 850 mm
Weight: 720 kg
Flexion modulus: 80 cm³
Standard steel tube: 127 x 7,1 mm
Gas tube: 4" x 8,56 mm
Furniture tube: 127 x 7,1 mm
FE35 (for hydraulic tubes): 100 x 11 mm
Stainless steel AISI304-318: 114,3 x 5,6 mm
Stainless steel AISI308 (food industry): 114,3 x 5,6 mm
Brass soft: 139,7 x 8,8 mm
Hard copper and aluminium: 139,7 x 8,8 mm
Soft copper: 139,7 x 8,8 mm
Conduit tube (TAZ): 120 x 9 mm
Mepla, Gebereit and similar: 120 x 6.5 mm
Roundbar solid (S275JO): 90 mm
Squarebar solid (S275JO): 75 x 75 mm
Flatsteel solid (S275JO): 100 x 50 mm
Square profile (S275JO): 120 x 60 x 9 bzw. 90 x 90 x 10 mm
T-profile (S275JO): 100 x 100 x 10 mm
U-profile (S275JO): 100 x 100 x 10 mm
Max. bending radius: 700 mm
Min. bending radius: 36 mm
Min. tube Ø: 10 mm
Max. bending speed: 0 - 0,75 r/min
Motor: 3.5 kW
Length: 850 mm
Width: 1200 mm
Height: 850 mm
Weight: 720 kg
Standard steel tube: 127 x 7,1 mm
Gas tube: 4" x 8,56 mm
Furniture tube: 127 x 7,1 mm
FE35 (for hydraulic tubes): 100 x 11 mm
Stainless steel AISI304-318: 114,3 x 5,6 mm
Stainless steel AISI308 (food industry): 114,3 x 5,6 mm
Brass soft: 139,7 x 8,8 mm
Hard copper and aluminium: 139,7 x 8,8 mm
Soft copper: 139,7 x 8,8 mm
Conduit tube (TAZ): 120 x 9 mm
Mepla, Gebereit and similar: 120 x 6.5 mm
Roundbar solid (S275JO): 90 mm
Squarebar solid (S275JO): 75 x 75 mm
Flatsteel solid (S275JO): 100 x 50 mm
Square profile (S275JO): 120 x 60 x 9 bzw. 90 x 90 x 10 mm
T-profile (S275JO): 100 x 100 x 10 mm
U-profile (S275JO): 100 x 100 x 10 mm
Max. bending radius: 700 mm
Min. bending radius: 36 mm
Min. tube Ø: 10 mm
Max. bending speed: 0 - 0,75 r/min
Motor: 3.5 kW
Length: 850 mm
Width: 1200 mm
Height: 850 mm
Weight: 720 kg
2
Metal working and machine toolsSheet metal working machinesPipe-bending machines
Flexion modulus: 43 cm³
Standard steel tube: 100 x 6 mm
Gas tube: 3" 1/2 x 5,74 mm
Furniture tube: 100 x 6 mm
FE35 (for hydraulic tubes): 100 x 7,5 mm
Stainless steel AISI304-318: 100 x 3,6 mm
Stainless steel AISI308 (food industry): 100 x 3,6 mm
Brass soft: 114.3 x 6,3 mm
Hard copper and aluminium: 114,3 x 6,3 mm
Soft copper: 114,3 x 6,3 mm
Conduit tube (TAZ): 100 x 6 mm
Mepla, Gebereit and similar: 100 x 5 mm
Roundbar solid (S275JO): 70 mm
Squarebar solid (S275JO): 60 x 60 mm
Flatsteel solid (S275JO): 80 x 40 mm
Square profile (S275JO): 100 x 60 x 4 bzw. 90 x 90 x 4 mm
T-profile (S275JO): 90 x 90 x 6 mm
U-profile (S275JO): 90 x 90 x 6 mm
Max. bending radius: 400 mm
Min. bending radius: 36 mm
Min. tube Ø: 10 mm
Max. bending speed: 0 - 1,3 r/min
Motor: 3.5 kW
Length: 500 mm
Width: 1200 mm
Height: 850 mm
Weight: 480 kg
Flexion modulus: 43 cm³
Standard steel tube: 100 x 6 mm
Gas tube: 3" 1/2 x 5,74 mm
Furniture tube: 100 x 6 mm
FE35 (for hydraulic tubes): 100 x 7,5 mm
Stainless steel AISI304-318: 100 x 3,6 mm
Stainless steel AISI308 (food industry): 100 x 3,6 mm
Brass soft: 114.3 x 6,3 mm
Hard copper and aluminium: 114,3 x 6,3 mm
Soft copper: 114,3 x 6,3 mm
Conduit tube (TAZ): 100 x 6 mm
Mepla, Gebereit and similar: 100 x 5 mm
Roundbar solid (S275JO): 70 mm
Squarebar solid (S275JO): 60 x 60 mm
Flatsteel solid (S275JO): 80 x 40 mm
Square profile (S275JO): 100 x 60 x 4 bzw. 90 x 90 x 4 mm
T-profile (S275JO): 90 x 90 x 6 mm
U-profile (S275JO): 90 x 90 x 6 mm
Max. bending radius: 400 mm
Min. bending radius: 36 mm
Min. tube Ø: 10 mm
Max. bending speed: 0 - 1,3 r/min
Motor: 3.5 kW
Length: 500 mm
Width: 1200 mm
Height: 850 mm
Weight: 480 kg
Standard steel tube: 100 x 6 mm
Gas tube: 3" 1/2 x 5,74 mm
Furniture tube: 100 x 6 mm
FE35 (for hydraulic tubes): 100 x 7,5 mm
Stainless steel AISI304-318: 100 x 3,6 mm
Stainless steel AISI308 (food industry): 100 x 3,6 mm
Brass soft: 114.3 x 6,3 mm
Hard copper and aluminium: 114,3 x 6,3 mm
Soft copper: 114,3 x 6,3 mm
Conduit tube (TAZ): 100 x 6 mm
Mepla, Gebereit and similar: 100 x 5 mm
Roundbar solid (S275JO): 70 mm
Squarebar solid (S275JO): 60 x 60 mm
Flatsteel solid (S275JO): 80 x 40 mm
Square profile (S275JO): 100 x 60 x 4 bzw. 90 x 90 x 4 mm
T-profile (S275JO): 90 x 90 x 6 mm
U-profile (S275JO): 90 x 90 x 6 mm
Max. bending radius: 400 mm
Min. bending radius: 36 mm
Min. tube Ø: 10 mm
Max. bending speed: 0 - 1,3 r/min
Motor: 3.5 kW
Length: 500 mm
Width: 1200 mm
Height: 850 mm
Weight: 480 kg
2
Metal working and machine toolsSheet metal working machinesPipe-bending machines
Flexion modulus: 10.5 cm³
Standard steel tube: 60 x 3 mm
Gas tube: 2"Gas x 4 mm
Furniture tube: 60 x 4 mm
FE35 (for hydraulic tubes): 64 x 4 mm
Stainless steel AISI304-318: 64 x 3 mm
Stainless steel AISI308 (food industry): 60 x 4 mm
Brass soft: 60 x 4 mm
Hard copper and aluminium: 64 x 4 mm
Soft copper: 64 x 4 mm
Conduit tube (TAZ): 60 x 4 mm
Mepla, Gebereit and similar: 50 x 4 mm
Roundbar solid (S275JO): 35 mm
Squarebar solid (S275JO): 30 x 30 mm
Flatsteel solid (S275JO): 10 x 60 mm
Square profile (S275JO): 25 x 50 x 3 bzw. 50 x 50 x 3 mm
T-profile (S275JO): 50 x 50 x 6 mm
U-profile (S275JO): 40 x 20 x 6 mm
Max. bending radius: 300 mm
Min. bending radius: 10 mm
Min. tube Ø: 10 mm
Max. bending speed: 1,25 / 2,60 r/min
Motor: 1.5 kW
Length: 595 mm
Width: 363 mm
Height: 900 mm
Weight: 130 kg
Flexion modulus: 10.5 cm³
Standard steel tube: 60 x 3 mm
Gas tube: 2"Gas x 4 mm
Furniture tube: 60 x 4 mm
FE35 (for hydraulic tubes): 64 x 4 mm
Stainless steel AISI304-318: 64 x 3 mm
Stainless steel AISI308 (food industry): 60 x 4 mm
Brass soft: 60 x 4 mm
Hard copper and aluminium: 64 x 4 mm
Soft copper: 64 x 4 mm
Conduit tube (TAZ): 60 x 4 mm
Mepla, Gebereit and similar: 50 x 4 mm
Roundbar solid (S275JO): 35 mm
Squarebar solid (S275JO): 30 x 30 mm
Flatsteel solid (S275JO): 10 x 60 mm
Square profile (S275JO): 25 x 50 x 3 bzw. 50 x 50 x 3 mm
T-profile (S275JO): 50 x 50 x 6 mm
U-profile (S275JO): 40 x 20 x 6 mm
Max. bending radius: 300 mm
Min. bending radius: 10 mm
Min. tube Ø: 10 mm
Max. bending speed: 1,25 / 2,60 r/min
Motor: 1.5 kW
Length: 595 mm
Width: 363 mm
Height: 900 mm
Weight: 130 kg
Standard steel tube: 60 x 3 mm
Gas tube: 2"Gas x 4 mm
Furniture tube: 60 x 4 mm
FE35 (for hydraulic tubes): 64 x 4 mm
Stainless steel AISI304-318: 64 x 3 mm
Stainless steel AISI308 (food industry): 60 x 4 mm
Brass soft: 60 x 4 mm
Hard copper and aluminium: 64 x 4 mm
Soft copper: 64 x 4 mm
Conduit tube (TAZ): 60 x 4 mm
Mepla, Gebereit and similar: 50 x 4 mm
Roundbar solid (S275JO): 35 mm
Squarebar solid (S275JO): 30 x 30 mm
Flatsteel solid (S275JO): 10 x 60 mm
Square profile (S275JO): 25 x 50 x 3 bzw. 50 x 50 x 3 mm
T-profile (S275JO): 50 x 50 x 6 mm
U-profile (S275JO): 40 x 20 x 6 mm
Max. bending radius: 300 mm
Min. bending radius: 10 mm
Min. tube Ø: 10 mm
Max. bending speed: 1,25 / 2,60 r/min
Motor: 1.5 kW
Length: 595 mm
Width: 363 mm
Height: 900 mm
Weight: 130 kg
2
Metal working and machine toolsLathes
Swing over bed: 860 mm
Distance between centers: 3000 mm
Centre height: 430 mm
Spindle bore: 132 mm
swing over cross slide: 620 mm
Width of bed: 560 mm
Spindle nose / DIN55027: 11
Spindle taper: 140 M
Spindle speed steps: 17
Spindle revs: Array rpm
Number of feeds: 150
Longitudinal feed range: 0.039 - 18 mm/r
Cross feed range: 0.02 - 9 mm/r
Metric thread range: 0.5 - 180 mm
Inch thread range: 60 - 1/6 Tpi
Module thread range: 0.125 - 45
DP thread range: 240 - 2/3
Cross slide travel: 435 mm
Top slide travel: 150 mm
Tailstock quill diameter: 105 mm
Tailstock quill taper: 6 MK
Tailstock travel: 225 mm
Motor power: 15 kW
Length: 3470 mm
Width: 1700 mm
Height: 1730 mm
Weight: 4650 kg
Swing over bed: 860 mm
Distance between centers: 3000 mm
Centre height: 430 mm
Spindle bore: 132 mm
swing over cross slide: 620 mm
Width of bed: 560 mm
Spindle nose / DIN55027: 11
Spindle taper: 140 M
Spindle speed steps: 17
Spindle revs: Array rpm
Number of feeds: 150
Longitudinal feed range: 0.039 - 18 mm/r
Cross feed range: 0.02 - 9 mm/r
Metric thread range: 0.5 - 180 mm
Inch thread range: 60 - 1/6 Tpi
Module thread range: 0.125 - 45
DP thread range: 240 - 2/3
Cross slide travel: 435 mm
Top slide travel: 150 mm
Tailstock quill diameter: 105 mm
Tailstock quill taper: 6 MK
Tailstock travel: 225 mm
Motor power: 15 kW
Length: 3470 mm
Width: 1700 mm
Height: 1730 mm
Weight: 4650 kg
Distance between centers: 3000 mm
Centre height: 430 mm
Spindle bore: 132 mm
swing over cross slide: 620 mm
Width of bed: 560 mm
Spindle nose / DIN55027: 11
Spindle taper: 140 M
Spindle speed steps: 17
Spindle revs: Array rpm
Number of feeds: 150
Longitudinal feed range: 0.039 - 18 mm/r
Cross feed range: 0.02 - 9 mm/r
Metric thread range: 0.5 - 180 mm
Inch thread range: 60 - 1/6 Tpi
Module thread range: 0.125 - 45
DP thread range: 240 - 2/3
Cross slide travel: 435 mm
Top slide travel: 150 mm
Tailstock quill diameter: 105 mm
Tailstock quill taper: 6 MK
Tailstock travel: 225 mm
Motor power: 15 kW
Length: 3470 mm
Width: 1700 mm
Height: 1730 mm
Weight: 4650 kg
2
Metal working and machine toolsLathes
Swing over bed: 400 mm
Distance between centers: 750 mm
Centre height: 200 mm
Spindle bore: 52 mm
swing over cross slide: 235 mm
Width of bed: 320 mm
Spindle nose / DIN55027: 6
Spindle taper: 6 M
Revs continuous variable in gear steps: 4
Revs continuous variable: 18-98, 48-265, 144-790, 385-2.120 U/min rpm
Number of feeds: 80
Longitudinal feed range: 0.015 - 0.6 mm/r
Cross feed range: 0.0075 - 0.3 mm/r
Number of threads: 40
Metric thread range: 0.25 - 7.5 mm
Inch thread range: 120 - 4 Tpi
Module thread range: 0.0625 - 1.875
DP thread range: Array
Cross slide travel: 235 mm
Top slide travel: 110 mm
Tailstock quill diameter: 50 mm
Tailstock quill taper: 4 MK
Tailstock travel: 100 mm
Motor power: 7.5 kW
Weight: 1530 kg
Swing over bed: 400 mm
Distance between centers: 750 mm
Centre height: 200 mm
Spindle bore: 52 mm
swing over cross slide: 235 mm
Width of bed: 320 mm
Spindle nose / DIN55027: 6
Spindle taper: 6 M
Revs continuous variable in gear steps: 4
Revs continuous variable: 18-98, 48-265, 144-790, 385-2.120 U/min rpm
Number of feeds: 80
Longitudinal feed range: 0.015 - 0.6 mm/r
Cross feed range: 0.0075 - 0.3 mm/r
Number of threads: 40
Metric thread range: 0.25 - 7.5 mm
Inch thread range: 120 - 4 Tpi
Module thread range: 0.0625 - 1.875
DP thread range: Array
Cross slide travel: 235 mm
Top slide travel: 110 mm
Tailstock quill diameter: 50 mm
Tailstock quill taper: 4 MK
Tailstock travel: 100 mm
Motor power: 7.5 kW
Weight: 1530 kg
Distance between centers: 750 mm
Centre height: 200 mm
Spindle bore: 52 mm
swing over cross slide: 235 mm
Width of bed: 320 mm
Spindle nose / DIN55027: 6
Spindle taper: 6 M
Revs continuous variable in gear steps: 4
Revs continuous variable: 18-98, 48-265, 144-790, 385-2.120 U/min rpm
Number of feeds: 80
Longitudinal feed range: 0.015 - 0.6 mm/r
Cross feed range: 0.0075 - 0.3 mm/r
Number of threads: 40
Metric thread range: 0.25 - 7.5 mm
Inch thread range: 120 - 4 Tpi
Module thread range: 0.0625 - 1.875
DP thread range: Array
Cross slide travel: 235 mm
Top slide travel: 110 mm
Tailstock quill diameter: 50 mm
Tailstock quill taper: 4 MK
Tailstock travel: 100 mm
Motor power: 7.5 kW
Weight: 1530 kg
2
Metal working and machine toolsLathes
Swing over bed: 1320 mm
Distance between centers: 3000 mm
Centre height: 625 mm
Spindle bore: 155 mm
swing over cross slide: 940 mm
Width of bed: 700 mm
Spindle nose / DIN55027: 15
Spindle taper: 160 M
Revs continuous variable in gear steps: 4
Revs continuous variable: 3,7 - 15,6, 14,7 - 62, 58 - 250, 235 - 1.000 U/min rpm
Number of feeds: 160
Longitudinal feed range: 0.032 - 38.9 mm/r
Cross feed range: 0.016 - 19.45 mm/r
Metric thread range: 0.5 - 480 mm
Inch thread range: 1/16 - 60 Tpi
Module thread range: 0.125 - 120
DP thread range: Array
Cross slide travel: 685 mm
Top slide travel: 270 mm
Tailstock quill diameter: 125 mm
Tailstock quill taper: 6 MK
Tailstock travel: 260 mm
Motor power: 30 kW
Weight: 8550 kg
Swing over bed: 1320 mm
Distance between centers: 3000 mm
Centre height: 625 mm
Spindle bore: 155 mm
swing over cross slide: 940 mm
Width of bed: 700 mm
Spindle nose / DIN55027: 15
Spindle taper: 160 M
Revs continuous variable in gear steps: 4
Revs continuous variable: 3,7 - 15,6, 14,7 - 62, 58 - 250, 235 - 1.000 U/min rpm
Number of feeds: 160
Longitudinal feed range: 0.032 - 38.9 mm/r
Cross feed range: 0.016 - 19.45 mm/r
Metric thread range: 0.5 - 480 mm
Inch thread range: 1/16 - 60 Tpi
Module thread range: 0.125 - 120
DP thread range: Array
Cross slide travel: 685 mm
Top slide travel: 270 mm
Tailstock quill diameter: 125 mm
Tailstock quill taper: 6 MK
Tailstock travel: 260 mm
Motor power: 30 kW
Weight: 8550 kg
Distance between centers: 3000 mm
Centre height: 625 mm
Spindle bore: 155 mm
swing over cross slide: 940 mm
Width of bed: 700 mm
Spindle nose / DIN55027: 15
Spindle taper: 160 M
Revs continuous variable in gear steps: 4
Revs continuous variable: 3,7 - 15,6, 14,7 - 62, 58 - 250, 235 - 1.000 U/min rpm
Number of feeds: 160
Longitudinal feed range: 0.032 - 38.9 mm/r
Cross feed range: 0.016 - 19.45 mm/r
Metric thread range: 0.5 - 480 mm
Inch thread range: 1/16 - 60 Tpi
Module thread range: 0.125 - 120
DP thread range: Array
Cross slide travel: 685 mm
Top slide travel: 270 mm
Tailstock quill diameter: 125 mm
Tailstock quill taper: 6 MK
Tailstock travel: 260 mm
Motor power: 30 kW
Weight: 8550 kg
2
Metal working and machine toolsLathes
Swing over bed: 1320 mm
Distance between centers: 3000 mm
Centre height: 625 mm
Spindle bore: 155 mm
swing over cross slide: 940 mm
Width of bed: 700 mm
Spindle nose / DIN55027: 15
Spindle taper: 160 M
Spindle speed steps: 5 - 1000
Number of feeds: 160
Longitudinal feed range: 0.032 - 38.9 mm/r
Cross feed range: 0.016 - 19.45 mm/r
Metric thread range: 0.5 - 480 mm
Inch thread range: 60 - 1/16 Tpi
Module thread range: 0.125 - 120
DP thread range: Array
Cross slide travel: 685 mm
Top slide travel: 270 mm
Tailstock quill diameter: 125 mm
Tailstock quill taper: 6 MK
Tailstock travel: 260 mm
Weight: 8550 kg
Swing over bed: 1320 mm
Distance between centers: 3000 mm
Centre height: 625 mm
Spindle bore: 155 mm
swing over cross slide: 940 mm
Width of bed: 700 mm
Spindle nose / DIN55027: 15
Spindle taper: 160 M
Spindle speed steps: 5 - 1000
Number of feeds: 160
Longitudinal feed range: 0.032 - 38.9 mm/r
Cross feed range: 0.016 - 19.45 mm/r
Metric thread range: 0.5 - 480 mm
Inch thread range: 60 - 1/16 Tpi
Module thread range: 0.125 - 120
DP thread range: Array
Cross slide travel: 685 mm
Top slide travel: 270 mm
Tailstock quill diameter: 125 mm
Tailstock quill taper: 6 MK
Tailstock travel: 260 mm
Weight: 8550 kg
Distance between centers: 3000 mm
Centre height: 625 mm
Spindle bore: 155 mm
swing over cross slide: 940 mm
Width of bed: 700 mm
Spindle nose / DIN55027: 15
Spindle taper: 160 M
Spindle speed steps: 5 - 1000
Number of feeds: 160
Longitudinal feed range: 0.032 - 38.9 mm/r
Cross feed range: 0.016 - 19.45 mm/r
Metric thread range: 0.5 - 480 mm
Inch thread range: 60 - 1/16 Tpi
Module thread range: 0.125 - 120
DP thread range: Array
Cross slide travel: 685 mm
Top slide travel: 270 mm
Tailstock quill diameter: 125 mm
Tailstock quill taper: 6 MK
Tailstock travel: 260 mm
Weight: 8550 kg