11
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18617
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Ref. no.: 18617
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
13
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18616
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Ref. no.: 18616
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
13
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18615
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Ref. no.: 18615
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Manufacturer: DEMAG
Year of construction: 2007
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 25 mm
Injection volume: 51 cm³
Shot weight: 45 g
Injection pressure: 2000 bar
Measurements and weight
Dimensions: 4,3 x 1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
8
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18614
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 18 mm
Injection volume: 26 cm³
Shot weight: 23 g
Injection pressure: 2800 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Ref. no.: 18614
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 18 mm
Injection volume: 26 cm³
Shot weight: 23 g
Injection pressure: 2800 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 18 mm
Injection volume: 26 cm³
Shot weight: 23 g
Injection pressure: 2800 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
13
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18613
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 74 cm³
Shot weight: 60 g
Injection pressure: 1390 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Ref. no.: 18613
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 74 cm³
Shot weight: 60 g
Injection pressure: 1390 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 30 mm
Injection volume: 74 cm³
Shot weight: 60 g
Injection pressure: 1390 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
13
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18612
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 22 mm
Injection volume: 39 cm³
Shot weight: 35 g
Injection pressure: 2500 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Ref. no.: 18612
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 22 mm
Injection volume: 39 cm³
Shot weight: 35 g
Injection pressure: 2500 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
Manufacturer: DEMAG
Year of construction: 2006
Clamping unit
Clamping force: 80 ton
Opening stroke: 340 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 150 mm
Injection unit
Screw diameter: 22 mm
Injection volume: 39 cm³
Shot weight: 35 g
Injection pressure: 2500 bar
Measurements and weight
Dimensions: 4,3 x1,3 x 2,3 m
Machine weight: 4750 kg
Further information:
A Technology That Stands Out in Energy Efficiency: Less Energy, Higher Precision
The Demag IntElect series is one of the pioneering machines that introduced all-electric drive technology to the plastic injection moulding industry in the late 2000s. Unlike conventional hydraulic systems where pumps and cooling circuits run continuously, the IntElect's servo drive only activates when movement is actually required. This fundamental difference delivers 50 – 70% energy savings compared to hydraulic machines, dramatically reducing annual operating costs.
Motor System — Siemens MOTICS 3
Main Drive Motor · Water-Cooled Servo Motor
The main drive unit that controls all clamping and injection movements with high precision.
Plasticising Motor · Water-Cooled Servo Motor
Based on the same Siemens MOTICS 3 platform, this motor melts material homogeneously through precise speed and torque control; its water-cooled design ensures stable operation during long-term intensive production.
5-Axis Full Servo Control
The machine is equipped with 5 independent servo motors. Clamping, injection, screw retraction, ejector and plasticising axes all operate under full servo control. Since each axis can be programmed independently, all movements can be executed simultaneously. This architecture delivers micron-level repeatable precision, shorter cycle times and minimum mechanical loss compared to hydraulic systems.
NC4 Control System
The keyboard-based NC4 system manages all machine parameters — including injection profile, mould protection and cycle analysis — from a single screen.
6
Food machinesMixing machinery
Joni OP300 electric steam jacketed mixing kettle, 2013, DC Norris / Joni OP300, stainless, 300L with agitation and scrap surface, perfect for cooking and mixing stocks, soups, sauces, preserves, pastry fillings and more, can either use tap or tilt to discharge, 3Ph
Joni OP300 electric steam jacketed mixing kettle, 2013, DC Norris / Joni OP300, stainless, 300L with agitation and scrap surface, perfect for cooking and mixing stocks, soups, sauces, preserves, pastry fillings and more, can either use tap or tilt to discharge, 3Ph
7
Food machinesMixing machinery
Joni OP200 electric steam jacketed mixing kettle, 2015, DC Norris / Joni OP200, stainless, 200L with agitation and scrap surface, perfect for cooking and mixing stocks, soups, sauces, preserves, pastry fillings and more, can either use tap or tilt to discharge, 3Ph
Joni OP200 electric steam jacketed mixing kettle, 2015, DC Norris / Joni OP200, stainless, 200L with agitation and scrap surface, perfect for cooking and mixing stocks, soups, sauces, preserves, pastry fillings and more, can either use tap or tilt to discharge, 3Ph
7
Food machinesOther
Riggs 1000 Twin head depositor, 2016, Stainless frame, twin head depositor, one head fills from 50ml to 600ml and the other from 125ml to 1200ml, on mobile scissor lift table
Riggs 1000 Twin head depositor, 2016, Stainless frame, twin head depositor, one head fills from 50ml to 600ml and the other from 125ml to 1200ml, on mobile scissor lift table
13
Plastic processing machinesPeripheral equipment
Ref. no.: 18439
Manufacturer: MOTAN
Year of construction: 1995
Further information:
MOTAN Central Drying & Vacuum Conveying System
Complete MOTAN central drying and automatic material conveying system for plastic injection molding applications.
The system includes:
* 15 pcs stainless steel drying hoppers
* Hopper capacity: 60 liters each
The system was used in technical plastics production and is suitable for processing hygroscopic materials such as:
PA, PC, PET, PBT, ABS, TPU and other engineering plastics.
System Components
1. MOTAN ADC 200/10 Dry Air Generator
* Year of manufacture: 1995
* Dry air capacity: approx. 200 m³/h
* Heating power: approx. 19.5 kW
* Central dry air generation system
* Desiccant drying technology
Function:
Provides low-humidity hot air for the drying hoppers.
2. MOTAN LA net 200 Central Control System
* Year of manufacture: 2006
* Central process and automation control unit
* Touchscreen operator panel
* Drying and conveying process management
* Alarm and monitoring functions
Function:
Central control of all drying, conveying and material distribution processes.
3. Drying Hoppers
* 15 pcs stainless steel drying hoppers
* Hopper volume: 60 liters each
* Central dry air connection
* Automatic material loading
* Suitable for technical plastics drying
4. Central Vacuum Conveying System
* Elmo Rietschle central vacuum pump
* Automatic granule conveying system
* Central material distribution
* Multi-machine supply capability
5. Stainless Steel Piping & Filter System
* Central conveying pipework
* Filter units
* Material loaders
* Automatic distribution station
Working Principle
Plastic granules are automatically conveyed through the central vacuum system into the drying hoppers.
The MOTAN ADC 200/10 dry air generator produces low-humidity hot air which continuously circulates through the material inside the hoppers.
During this process, moisture is removed from the plastic granules to prepare the material for injection molding production.
After drying, the material is automatically transported through the central conveying lines and distributed to the connected injection molding machines.
All drying and conveying processes are centrally controlled via the MOTAN LA net 200 control system
Condition
The system was in production operation until dismantling.
Further technical information, photos and videos available on request.
Ref. no.: 18439
Manufacturer: MOTAN
Year of construction: 1995
Further information:
MOTAN Central Drying & Vacuum Conveying System
Complete MOTAN central drying and automatic material conveying system for plastic injection molding applications.
The system includes:
* 15 pcs stainless steel drying hoppers
* Hopper capacity: 60 liters each
The system was used in technical plastics production and is suitable for processing hygroscopic materials such as:
PA, PC, PET, PBT, ABS, TPU and other engineering plastics.
System Components
1. MOTAN ADC 200/10 Dry Air Generator
* Year of manufacture: 1995
* Dry air capacity: approx. 200 m³/h
* Heating power: approx. 19.5 kW
* Central dry air generation system
* Desiccant drying technology
Function:
Provides low-humidity hot air for the drying hoppers.
2. MOTAN LA net 200 Central Control System
* Year of manufacture: 2006
* Central process and automation control unit
* Touchscreen operator panel
* Drying and conveying process management
* Alarm and monitoring functions
Function:
Central control of all drying, conveying and material distribution processes.
3. Drying Hoppers
* 15 pcs stainless steel drying hoppers
* Hopper volume: 60 liters each
* Central dry air connection
* Automatic material loading
* Suitable for technical plastics drying
4. Central Vacuum Conveying System
* Elmo Rietschle central vacuum pump
* Automatic granule conveying system
* Central material distribution
* Multi-machine supply capability
5. Stainless Steel Piping & Filter System
* Central conveying pipework
* Filter units
* Material loaders
* Automatic distribution station
Working Principle
Plastic granules are automatically conveyed through the central vacuum system into the drying hoppers.
The MOTAN ADC 200/10 dry air generator produces low-humidity hot air which continuously circulates through the material inside the hoppers.
During this process, moisture is removed from the plastic granules to prepare the material for injection molding production.
After drying, the material is automatically transported through the central conveying lines and distributed to the connected injection molding machines.
All drying and conveying processes are centrally controlled via the MOTAN LA net 200 control system
Condition
The system was in production operation until dismantling.
Further technical information, photos and videos available on request.
Manufacturer: MOTAN
Year of construction: 1995
Further information:
MOTAN Central Drying & Vacuum Conveying System
Complete MOTAN central drying and automatic material conveying system for plastic injection molding applications.
The system includes:
* 15 pcs stainless steel drying hoppers
* Hopper capacity: 60 liters each
The system was used in technical plastics production and is suitable for processing hygroscopic materials such as:
PA, PC, PET, PBT, ABS, TPU and other engineering plastics.
System Components
1. MOTAN ADC 200/10 Dry Air Generator
* Year of manufacture: 1995
* Dry air capacity: approx. 200 m³/h
* Heating power: approx. 19.5 kW
* Central dry air generation system
* Desiccant drying technology
Function:
Provides low-humidity hot air for the drying hoppers.
2. MOTAN LA net 200 Central Control System
* Year of manufacture: 2006
* Central process and automation control unit
* Touchscreen operator panel
* Drying and conveying process management
* Alarm and monitoring functions
Function:
Central control of all drying, conveying and material distribution processes.
3. Drying Hoppers
* 15 pcs stainless steel drying hoppers
* Hopper volume: 60 liters each
* Central dry air connection
* Automatic material loading
* Suitable for technical plastics drying
4. Central Vacuum Conveying System
* Elmo Rietschle central vacuum pump
* Automatic granule conveying system
* Central material distribution
* Multi-machine supply capability
5. Stainless Steel Piping & Filter System
* Central conveying pipework
* Filter units
* Material loaders
* Automatic distribution station
Working Principle
Plastic granules are automatically conveyed through the central vacuum system into the drying hoppers.
The MOTAN ADC 200/10 dry air generator produces low-humidity hot air which continuously circulates through the material inside the hoppers.
During this process, moisture is removed from the plastic granules to prepare the material for injection molding production.
After drying, the material is automatically transported through the central conveying lines and distributed to the connected injection molding machines.
All drying and conveying processes are centrally controlled via the MOTAN LA net 200 control system
Condition
The system was in production operation until dismantling.
Further technical information, photos and videos available on request.
Metal working and machine toolsAccessories and spare parts
Filterleistung: . l/minVließbreite: . mmTemperatur: . °C
Filterleistung: . l/min
Vließbreite: . mm
Temperatur: . °C
Vließbreite: . mm
Temperatur: . °C
4
Process engineeringFilter and filter systems
Kühlmittelinhalt: 500 lFilterfläche: 800x900 mmRaumbedarf ca.: 2x1,4x1,5 mGesamtleistungsbedarf: kWMaschinengewicht ca.: 1 t
Kühlmittelinhalt: 500 l
Filterfläche: 800x900 mm
Raumbedarf ca.: 2x1,4x1,5 m
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: 1 t
Filterfläche: 800x900 mm
Raumbedarf ca.: 2x1,4x1,5 m
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: 1 t
10
Process engineeringFilter and filter systems
Literleistung: . lFörderdruck: . barKühlmittelinhalt: . lGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Literleistung: . l
Förderdruck: . bar
Kühlmittelinhalt: . l
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Förderdruck: . bar
Kühlmittelinhalt: . l
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
7
Process engineeringFilter and filter systems
Literleistung: . lFörderdruck: . barKühlmittelinhalt: . lGesamtleistungsbedarf: . kWMaschinengewicht ca.: . tRaumbedarf ca.: . m
Literleistung: . l
Förderdruck: . bar
Kühlmittelinhalt: . l
Gesamtleistungsbedarf: . kW
Maschinengewicht ca.: . t
Raumbedarf ca.: . m
Förderdruck: . bar
Kühlmittelinhalt: . l
Gesamtleistungsbedarf: . kW
Maschinengewicht ca.: . t
Raumbedarf ca.: . m
4
Process engineeringFilter and filter systems
Literleistung: . lFörderdruck: . barKühlmittelinhalt: . l
Literleistung: . l
Förderdruck: . bar
Kühlmittelinhalt: . l
Förderdruck: . bar
Kühlmittelinhalt: . l
10
Process engineeringFilter and filter systems
Förderdruck: . barKühlmittelinhalt: . lExpansionsbereich: . mm
Förderdruck: . bar
Kühlmittelinhalt: . l
Expansionsbereich: . mm
Kühlmittelinhalt: . l
Expansionsbereich: . mm
7
Metal working and machine toolsAccessories and spare parts
Lagernummer: 1077-Z01225Maschinenart: ErsatzteileFabrikat: SiemensTyp: Netzfilter E/RBaujahr: unbekanntSteuerung: konventionellLagerort: DorstenUrsprungsland: -Lieferzeit: sofortFrachtbasis: ab StandortPreis: Auf Anfrage
Lagernummer: 1077-Z01225
Maschinenart: Ersatzteile
Fabrikat: Siemens
Typ: Netzfilter E/R
Baujahr: unbekannt
Steuerung: konventionell
Lagerort: Dorsten
Ursprungsland: -
Lieferzeit: sofort
Frachtbasis: ab Standort
Preis: Auf Anfrage
Maschinenart: Ersatzteile
Fabrikat: Siemens
Typ: Netzfilter E/R
Baujahr: unbekannt
Steuerung: konventionell
Lagerort: Dorsten
Ursprungsland: -
Lieferzeit: sofort
Frachtbasis: ab Standort
Preis: Auf Anfrage
7
Food machinesBeverage productionPumps
Riggs 1000 Transfer pump, 2012, stainless, filling range from 125ml to 1200ml, they pump directly from cooking kettles, tote bins, mixing vessels or IBC, provide damage free transfer of hot or cold liquid, semi liquid and suspended solid products
Riggs 1000 Transfer pump, 2012, stainless, filling range from 125ml to 1200ml, they pump directly from cooking kettles, tote bins, mixing vessels or IBC, provide damage free transfer of hot or cold liquid, semi liquid and suspended solid products
8
Food machinesOther
Winyard Midifill MKII Twin depositor, 2018, stainless, 200Kg hopper, Previously used Deposit weight: 250g - 1000g of sourcrout and potato salad. Product temperature: Chilled Through rate: 55 PPM @ 1Kg 1 quantity twin Midi-Fill MKII depositors mounted on a mobile trolley to provide 1.25 litres maximum displacement per stroke and to be complete with: 2 quantity 70mm diameter product bores , easy-clean pistons Bulk hopper with twin 3” diameter outlets, hopper to allow for Tote Bin tipper from the side Stainless steel mobile trolley to dock into position over the conveyor 2 quantity 36mm diameter extended general purpose nozzles to offer drip-free production"
Winyard Midifill MKII Twin depositor, 2018, stainless, 200Kg hopper, Previously used Deposit weight: 250g - 1000g of sourcrout and potato salad. Product temperature: Chilled Through rate: 55 PPM @ 1Kg 1 quantity twin Midi-Fill MKII depositors mounted on a mobile trolley to provide 1.25 litres maximum displacement per stroke and to be complete with: 2 quantity 70mm diameter product bores , easy-clean pistons Bulk hopper with twin 3” diameter outlets, hopper to allow for Tote Bin tipper from the side Stainless steel mobile trolley to dock into position over the conveyor 2 quantity 36mm diameter extended general purpose nozzles to offer drip-free production"
9
Food machinesPackaging machinery
Delfin Auriga 500 Flow wrapper, Serial: 11110, 2016, flow wrapper, jaw width 230mm, up to 120 cycles per min, infeed length 2100mm, overall length 3700mm, HMI touch screen controls, reel holder up to 500mm film, 3Ph
Delfin Auriga 500 Flow wrapper, Serial: 11110, 2016, flow wrapper, jaw width 230mm, up to 120 cycles per min, infeed length 2100mm, overall length 3700mm, HMI touch screen controls, reel holder up to 500mm film, 3Ph
3
Metal working and machine toolsSheet metal working machinesSection steel shears
Punching power: 50 ton
Throat depth: 177 mm
Number of stations: 5
Cylinder: 1
Max. diameter at sheet thickness (mild steel): 31 x 12 mm
Strokes: 34 1/min
Flat steel: 350 x 15 mm
Angle steel: 80 x 8 mm
Round / square steel: 35 / 30 mm
Notcher: 10 mm
Bending unit: 100 x 10 mm
Motor: 3 kW
Length: 1300 mm
Width: 1100 mm
Height: 1850 mm
Weight: 950 kg
Punching power: 50 ton
Throat depth: 177 mm
Number of stations: 5
Cylinder: 1
Max. diameter at sheet thickness (mild steel): 31 x 12 mm
Strokes: 34 1/min
Flat steel: 350 x 15 mm
Angle steel: 80 x 8 mm
Round / square steel: 35 / 30 mm
Notcher: 10 mm
Bending unit: 100 x 10 mm
Motor: 3 kW
Length: 1300 mm
Width: 1100 mm
Height: 1850 mm
Weight: 950 kg
Throat depth: 177 mm
Number of stations: 5
Cylinder: 1
Max. diameter at sheet thickness (mild steel): 31 x 12 mm
Strokes: 34 1/min
Flat steel: 350 x 15 mm
Angle steel: 80 x 8 mm
Round / square steel: 35 / 30 mm
Notcher: 10 mm
Bending unit: 100 x 10 mm
Motor: 3 kW
Length: 1300 mm
Width: 1100 mm
Height: 1850 mm
Weight: 950 kg
5
Food machinesBakery-, pastry equipmentCutting machines
Ward Bekker Auger Filler, Stainless frame, 25Kg stainless agitated hopper, 35mm diameter screw, with foot pedal, mobile, 3Ph
Ward Bekker Auger Filler, Stainless frame, 25Kg stainless agitated hopper, 35mm diameter screw, with foot pedal, mobile, 3Ph
8
Food machinesMeat processing
CE King TB4 Tablet counter, Stainless, electronic tablet or capsule counter, two channel, product hopper with top cover and vibration frequency control of product onto the feed chute, mounted on slat chain conveyor 3000mm x 100mm, fills up to 30 containers per min, 3Ph
CE King TB4 Tablet counter, Stainless, electronic tablet or capsule counter, two channel, product hopper with top cover and vibration frequency control of product onto the feed chute, mounted on slat chain conveyor 3000mm x 100mm, fills up to 30 containers per min, 3Ph
9
Food machinesMeat processing
Swiftpack SPC4P Tablet counter, Stainless, two lane digital tablet counter, designed for high precision counting of tablets and capsules, previously used to fill both plastic and glass bottles,
Swiftpack SPC4P Tablet counter, Stainless, two lane digital tablet counter, designed for high precision counting of tablets and capsules, previously used to fill both plastic and glass bottles,
6
Metal working and machine toolsSawingCircular saws
Saw blade diameter: 300 mm
Saw blade dimensions: 300 x (2)2,5 x 32 mm
Saw blade speed: Array rpm
Mitre left: 45 °
Mitre right: 45 °
Cutting capacity 0°: rund 102 mm, Quadratprofil 90 mm, Rechteckprofil 120 x 80 mm
Cutting capacity 45° right: rund 90 mm, Quadratprofil 80 mm, Rechteckprofil 90 x 70 mm
Cutting capacity 45° left: rund 80 mm, Quadratprofil 70 mm, Rechteckprofil 85 x 70 mm
Width: 500 mm
Depth: 1050 mm
Height: 990 mm
Weight: 135 kg
Saw blade diameter: 300 mm
Saw blade dimensions: 300 x (2)2,5 x 32 mm
Saw blade speed: Array rpm
Mitre left: 45 °
Mitre right: 45 °
Cutting capacity 0°: rund 102 mm, Quadratprofil 90 mm, Rechteckprofil 120 x 80 mm
Cutting capacity 45° right: rund 90 mm, Quadratprofil 80 mm, Rechteckprofil 90 x 70 mm
Cutting capacity 45° left: rund 80 mm, Quadratprofil 70 mm, Rechteckprofil 85 x 70 mm
Width: 500 mm
Depth: 1050 mm
Height: 990 mm
Weight: 135 kg
Saw blade dimensions: 300 x (2)2,5 x 32 mm
Saw blade speed: Array rpm
Mitre left: 45 °
Mitre right: 45 °
Cutting capacity 0°: rund 102 mm, Quadratprofil 90 mm, Rechteckprofil 120 x 80 mm
Cutting capacity 45° right: rund 90 mm, Quadratprofil 80 mm, Rechteckprofil 90 x 70 mm
Cutting capacity 45° left: rund 80 mm, Quadratprofil 70 mm, Rechteckprofil 85 x 70 mm
Width: 500 mm
Depth: 1050 mm
Height: 990 mm
Weight: 135 kg
8
Food machinesCatering technologyWashing machines
Electrolux EPPWELG Electronic pot washer, 4202015806, 2024, stainless, with wash tank, tank filter and wash and rinse arms, safe wash controls,
Electrolux EPPWELG Electronic pot washer, 4202015806, 2024, stainless, with wash tank, tank filter and wash and rinse arms, safe wash controls,
7
Food machinesBakery-, pastry equipmentCutting machines
Koneteollisuus F19S Meat Slicer, 2021, stainless, designed for cutting fresh and boneless meat into slices or strips, works well for slicing cooked or dried meats, liver, poultry, fish fillets as well as fruits and vegetables, up to 1500Kgs per hour, mobile, 1Ph
Koneteollisuus F19S Meat Slicer, 2021, stainless, designed for cutting fresh and boneless meat into slices or strips, works well for slicing cooked or dried meats, liver, poultry, fish fillets as well as fruits and vegetables, up to 1500Kgs per hour, mobile, 1Ph
4
Metal working and machine toolsOther
MESSSCHIEBER / SCHIEBLEHRE / NEU - UNBENUTZTSMW 3000x500mmMesslänge ca. 3000mmSchnabellänge ca. 500mmPyddlNonius 1/ 20mm nach WerksnormMaßstab u. Schieber aus AluprofilMessschnäbel aus Stahl - rostfrei gehärtetBlendfreie AblesungGewicht ca. 3,8 kgincl. Transportkasten
MESSSCHIEBER / SCHIEBLEHRE / NEU - UNBENUTZT
SMW 3000x500mm
Messlänge ca. 3000mm
Schnabellänge ca. 500mm
Pyddl
Nonius 1/ 20mm nach Werksnorm
Maßstab u. Schieber aus Aluprofil
Messschnäbel aus Stahl - rostfrei gehärtet
Blendfreie Ablesung
Gewicht ca. 3,8 kg
incl. Transportkasten
SMW 3000x500mm
Messlänge ca. 3000mm
Schnabellänge ca. 500mm
Pyddl
Nonius 1/ 20mm nach Werksnorm
Maßstab u. Schieber aus Aluprofil
Messschnäbel aus Stahl - rostfrei gehärtet
Blendfreie Ablesung
Gewicht ca. 3,8 kg
incl. Transportkasten
7
Metal working and machine toolsOther
Kühlmittel - Filteranlage KNOLL KF 600 / 1500<br /><br /><br />-CE -Kennung<br />-Kühlmittelbehälter<br />-Papierbandfilter<br />-Steuerung - OP 3<br />-Kühlmittelpumpen<br /><br />Abmaße:<br />LxBxH 2,4x1,2x1,5 Meter / Gewicht 1200Kg
Kühlmittel - Filteranlage KNOLL KF 600 / 1500<br /><br /><br />-CE -Kennung<br />-Kühlmittelbehälter<br />-Papierbandfilter<br />-Steuerung - OP 3<br />-Kühlmittelpumpen<br /><br />Abmaße:<br />LxBxH 2,4x1,2x1,5 Meter / Gewicht 1200Kg
2
Metal working and machine toolsSheet metal working machinesBending machines
Shaft diameter: 50 - 60
Upper roll diameter: 180 mm
Rolls diameter: 180 mm
Lower roll diameter: 180 mm
Driven rolls: 3
Motor power: 3.75 kW
Speed: 6 m/min
Flat steel vertical position (section / min. diameter): 60x10 mm / 500 mm, 20x5 mm / 250 mm
Flat steel horizontal position (section / min. diameter): 80x20 mm / 500 mm, 50x5 mm / 250 mm
Square bar (section / min. diameter): 32x32 mm / 400 mm, 12x12 mm / 250 mm
Round bar (section / min. diameter): Ø 35 mm / 350 mm, Ø 10 mm / 250 mm
Tube (section / min. diameter): Ø 60x2 mm / 600 mm, Ø 15x1,5 mm / 200 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 50x25x3 mm / 450 mm, 20x15x2 mm / 250 mm
Form tube square (section / min. diameter): 45x3 mm / 600 mm, 20x2 mm / 300 mm
Angle leg outside (Querschnitt / min. Durchmesser): 60x60x6 mm / 650 mm, 30x30x4 mm / 350 mm
Angle leg inside (section / min. diameter): 50x50x5 mm / 550 mm, 30x30x4 mm / 350 mm
UPN leg outside (section / min. diameter): UPN 80 / 600 mm, UPN30 / 250 mm
UPN leg inside (section / min. diameter): UPN 65 / 600 mm, UPN 30 / 250 mm
IPN horizontal position (section / min. diameter): IPN 80 / 600 mm
Length: 1200 mm
Width: 850 mm
Height: 1200 mm
Weight: 955 kg
Shaft diameter: 50 - 60
Upper roll diameter: 180 mm
Rolls diameter: 180 mm
Lower roll diameter: 180 mm
Driven rolls: 3
Motor power: 3.75 kW
Speed: 6 m/min
Flat steel vertical position (section / min. diameter): 60x10 mm / 500 mm, 20x5 mm / 250 mm
Flat steel horizontal position (section / min. diameter): 80x20 mm / 500 mm, 50x5 mm / 250 mm
Square bar (section / min. diameter): 32x32 mm / 400 mm, 12x12 mm / 250 mm
Round bar (section / min. diameter): Ø 35 mm / 350 mm, Ø 10 mm / 250 mm
Tube (section / min. diameter): Ø 60x2 mm / 600 mm, Ø 15x1,5 mm / 200 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 50x25x3 mm / 450 mm, 20x15x2 mm / 250 mm
Form tube square (section / min. diameter): 45x3 mm / 600 mm, 20x2 mm / 300 mm
Angle leg outside (Querschnitt / min. Durchmesser): 60x60x6 mm / 650 mm, 30x30x4 mm / 350 mm
Angle leg inside (section / min. diameter): 50x50x5 mm / 550 mm, 30x30x4 mm / 350 mm
UPN leg outside (section / min. diameter): UPN 80 / 600 mm, UPN30 / 250 mm
UPN leg inside (section / min. diameter): UPN 65 / 600 mm, UPN 30 / 250 mm
IPN horizontal position (section / min. diameter): IPN 80 / 600 mm
Length: 1200 mm
Width: 850 mm
Height: 1200 mm
Weight: 955 kg
Upper roll diameter: 180 mm
Rolls diameter: 180 mm
Lower roll diameter: 180 mm
Driven rolls: 3
Motor power: 3.75 kW
Speed: 6 m/min
Flat steel vertical position (section / min. diameter): 60x10 mm / 500 mm, 20x5 mm / 250 mm
Flat steel horizontal position (section / min. diameter): 80x20 mm / 500 mm, 50x5 mm / 250 mm
Square bar (section / min. diameter): 32x32 mm / 400 mm, 12x12 mm / 250 mm
Round bar (section / min. diameter): Ø 35 mm / 350 mm, Ø 10 mm / 250 mm
Tube (section / min. diameter): Ø 60x2 mm / 600 mm, Ø 15x1,5 mm / 200 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 50x25x3 mm / 450 mm, 20x15x2 mm / 250 mm
Form tube square (section / min. diameter): 45x3 mm / 600 mm, 20x2 mm / 300 mm
Angle leg outside (Querschnitt / min. Durchmesser): 60x60x6 mm / 650 mm, 30x30x4 mm / 350 mm
Angle leg inside (section / min. diameter): 50x50x5 mm / 550 mm, 30x30x4 mm / 350 mm
UPN leg outside (section / min. diameter): UPN 80 / 600 mm, UPN30 / 250 mm
UPN leg inside (section / min. diameter): UPN 65 / 600 mm, UPN 30 / 250 mm
IPN horizontal position (section / min. diameter): IPN 80 / 600 mm
Length: 1200 mm
Width: 850 mm
Height: 1200 mm
Weight: 955 kg
3
Metal working and machine toolsSheet metal working machinesSection steel shears
Punching power: 60 ton
Throat depth: 250 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40 x 11 mm
Strokes: 32 1/min
Flat steel: 350 x 15 mm
Angle steel: 120 x 10 mm
Round / square steel: 45 / 40 mm
Notcher: 10 mm
Bending unit: max. 150x10 mm
Motor: 5.5 kW
Length: 1850 mm
Width: 1300 mm
Height: 2100 mm
Weight: 1390 kg
Punching power: 60 ton
Throat depth: 250 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40 x 11 mm
Strokes: 32 1/min
Flat steel: 350 x 15 mm
Angle steel: 120 x 10 mm
Round / square steel: 45 / 40 mm
Notcher: 10 mm
Bending unit: max. 150x10 mm
Motor: 5.5 kW
Length: 1850 mm
Width: 1300 mm
Height: 2100 mm
Weight: 1390 kg
Throat depth: 250 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40 x 11 mm
Strokes: 32 1/min
Flat steel: 350 x 15 mm
Angle steel: 120 x 10 mm
Round / square steel: 45 / 40 mm
Notcher: 10 mm
Bending unit: max. 150x10 mm
Motor: 5.5 kW
Length: 1850 mm
Width: 1300 mm
Height: 2100 mm
Weight: 1390 kg
3
Metal working and machine toolsSheet metal working machinesSection steel shears
Punching power: 130 ton
Throat depth: 600 mm
Number of stations: 5
Cylinder: 2
Max. diameter at sheet thickness (mild steel): 50x18 mm
Stroke: 80 mm
Flat steel: 600x18 (max. 600x20 mit Deformation) mm
Angle steel: 120x120x11 (max. 150x150x15 mit Deformation) mm
Round / square steel: 45/40 mm
Notcher: 130x12 mm
Bending unit: 250x12 mm
Motor: 15 kW
Punching power: 130 ton
Throat depth: 600 mm
Number of stations: 5
Cylinder: 2
Max. diameter at sheet thickness (mild steel): 50x18 mm
Stroke: 80 mm
Flat steel: 600x18 (max. 600x20 mit Deformation) mm
Angle steel: 120x120x11 (max. 150x150x15 mit Deformation) mm
Round / square steel: 45/40 mm
Notcher: 130x12 mm
Bending unit: 250x12 mm
Motor: 15 kW
Throat depth: 600 mm
Number of stations: 5
Cylinder: 2
Max. diameter at sheet thickness (mild steel): 50x18 mm
Stroke: 80 mm
Flat steel: 600x18 (max. 600x20 mit Deformation) mm
Angle steel: 120x120x11 (max. 150x150x15 mit Deformation) mm
Round / square steel: 45/40 mm
Notcher: 130x12 mm
Bending unit: 250x12 mm
Motor: 15 kW
6
Metal working and machine toolsSheet metal working machinesBending machines
Shaft diameter: 50
Upper roll diameter: 152 mm
Lower roll diameter: 162 mm
Driven rolls: 3
Motor power: 1.1 kW
Speed: 4 m/min
Flat steel vertical position (section / min. diameter): 60x10 mm / 600 mm, 20x10 mm / 300 mm
Flat steel horizontal position (section / min. diameter): 100x15 mm / 600 mm, 50 x 10 mm / 300 mm
Square bar (section / min. diameter): 35x35 mm / 600 mm, 15x15 mm / 300 mm
Round bar (section / min. diameter): 35 mm / 600 mm, Dm. 20 mm / 300 mm
Tube (section / min. diameter): 70x2 mm / 1200 mm, Dm. 25x1,5 mm / 400 mm, 2"x2,9 mm / 1000 mm, 1/2"x2,3 mm / 350 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 70x30x3 mm / 1500 mm, 30x15x2 mm / 400 mm
Form tube square (section / min. diameter): 50x50x3 mm / 1600 mm, 20x20x2 mm / 400 mm
Angle leg outside (Querschnitt / min. Durchmesser): 50x50x6 mm / 600 mm, 30x30x3 mm / 400 mm
Angle leg inside (section / min. diameter): 50x50x6 mm / 900 mm, 30x30x3 mm / 600 mm
Length: 810 mm
Width: 950 mm
Height: 1500 mm
Weight: 500 kg
Shaft diameter: 50
Upper roll diameter: 152 mm
Lower roll diameter: 162 mm
Driven rolls: 3
Motor power: 1.1 kW
Speed: 4 m/min
Flat steel vertical position (section / min. diameter): 60x10 mm / 600 mm, 20x10 mm / 300 mm
Flat steel horizontal position (section / min. diameter): 100x15 mm / 600 mm, 50 x 10 mm / 300 mm
Square bar (section / min. diameter): 35x35 mm / 600 mm, 15x15 mm / 300 mm
Round bar (section / min. diameter): 35 mm / 600 mm, Dm. 20 mm / 300 mm
Tube (section / min. diameter): 70x2 mm / 1200 mm, Dm. 25x1,5 mm / 400 mm, 2"x2,9 mm / 1000 mm, 1/2"x2,3 mm / 350 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 70x30x3 mm / 1500 mm, 30x15x2 mm / 400 mm
Form tube square (section / min. diameter): 50x50x3 mm / 1600 mm, 20x20x2 mm / 400 mm
Angle leg outside (Querschnitt / min. Durchmesser): 50x50x6 mm / 600 mm, 30x30x3 mm / 400 mm
Angle leg inside (section / min. diameter): 50x50x6 mm / 900 mm, 30x30x3 mm / 600 mm
Length: 810 mm
Width: 950 mm
Height: 1500 mm
Weight: 500 kg
Upper roll diameter: 152 mm
Lower roll diameter: 162 mm
Driven rolls: 3
Motor power: 1.1 kW
Speed: 4 m/min
Flat steel vertical position (section / min. diameter): 60x10 mm / 600 mm, 20x10 mm / 300 mm
Flat steel horizontal position (section / min. diameter): 100x15 mm / 600 mm, 50 x 10 mm / 300 mm
Square bar (section / min. diameter): 35x35 mm / 600 mm, 15x15 mm / 300 mm
Round bar (section / min. diameter): 35 mm / 600 mm, Dm. 20 mm / 300 mm
Tube (section / min. diameter): 70x2 mm / 1200 mm, Dm. 25x1,5 mm / 400 mm, 2"x2,9 mm / 1000 mm, 1/2"x2,3 mm / 350 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 70x30x3 mm / 1500 mm, 30x15x2 mm / 400 mm
Form tube square (section / min. diameter): 50x50x3 mm / 1600 mm, 20x20x2 mm / 400 mm
Angle leg outside (Querschnitt / min. Durchmesser): 50x50x6 mm / 600 mm, 30x30x3 mm / 400 mm
Angle leg inside (section / min. diameter): 50x50x6 mm / 900 mm, 30x30x3 mm / 600 mm
Length: 810 mm
Width: 950 mm
Height: 1500 mm
Weight: 500 kg
5
Metal working and machine toolsSheet metal working machinesBending machines
Shaft diameter: 30
Upper roll diameter: 148 mm
Lower roll diameter: 118 mm
Driven rolls: 2
Motor power: 0.7 / 0,85 kW
Speed: 2/4 m/min
Flat steel vertical position (section / min. diameter): 50x10 mm / 1.800 mm, 20x6 mm / 300 mm
Flat steel horizontal position (section / min. diameter): 80x15 mm / 700 mm, 30 x 6 mm / 400 mm
Square bar (section / min. diameter): 30x30 mm / 900 mm, 10x10 mm / 200 mm
Round bar (section / min. diameter): Ø 30 mm / 900 mm, Ø 10 mm / 200 mm
Tube (section / min. diameter): Ø 60x1,5 mm / 1.000 mm, Ø 25x1,5 mm / 600 mm, 1 1/2"x2,9 mm / 600 mm, 1/4"x1,8 mm / 300 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 50x30x3 mm / 1.200 mm, 40x20x2 mm / 800 mm
Form tube square (section / min. diameter): 40x40x3 mm / 1.200 mm, 30x30x2 mm / 800 mm
Angle leg outside (Querschnitt / min. Durchmesser): 40x40x5 mm / 600 mm, 30x30x4 mm / 300 mm
Angle leg inside (section / min. diameter): 35x35x5 mm / 600 mm, 30x30x4 mm / 400 mm
Length: 600 mm
Width: 800 mm
Height: 1450 mm
Weight: 220 kg
Shaft diameter: 30
Upper roll diameter: 148 mm
Lower roll diameter: 118 mm
Driven rolls: 2
Motor power: 0.7 / 0,85 kW
Speed: 2/4 m/min
Flat steel vertical position (section / min. diameter): 50x10 mm / 1.800 mm, 20x6 mm / 300 mm
Flat steel horizontal position (section / min. diameter): 80x15 mm / 700 mm, 30 x 6 mm / 400 mm
Square bar (section / min. diameter): 30x30 mm / 900 mm, 10x10 mm / 200 mm
Round bar (section / min. diameter): Ø 30 mm / 900 mm, Ø 10 mm / 200 mm
Tube (section / min. diameter): Ø 60x1,5 mm / 1.000 mm, Ø 25x1,5 mm / 600 mm, 1 1/2"x2,9 mm / 600 mm, 1/4"x1,8 mm / 300 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 50x30x3 mm / 1.200 mm, 40x20x2 mm / 800 mm
Form tube square (section / min. diameter): 40x40x3 mm / 1.200 mm, 30x30x2 mm / 800 mm
Angle leg outside (Querschnitt / min. Durchmesser): 40x40x5 mm / 600 mm, 30x30x4 mm / 300 mm
Angle leg inside (section / min. diameter): 35x35x5 mm / 600 mm, 30x30x4 mm / 400 mm
Length: 600 mm
Width: 800 mm
Height: 1450 mm
Weight: 220 kg
Upper roll diameter: 148 mm
Lower roll diameter: 118 mm
Driven rolls: 2
Motor power: 0.7 / 0,85 kW
Speed: 2/4 m/min
Flat steel vertical position (section / min. diameter): 50x10 mm / 1.800 mm, 20x6 mm / 300 mm
Flat steel horizontal position (section / min. diameter): 80x15 mm / 700 mm, 30 x 6 mm / 400 mm
Square bar (section / min. diameter): 30x30 mm / 900 mm, 10x10 mm / 200 mm
Round bar (section / min. diameter): Ø 30 mm / 900 mm, Ø 10 mm / 200 mm
Tube (section / min. diameter): Ø 60x1,5 mm / 1.000 mm, Ø 25x1,5 mm / 600 mm, 1 1/2"x2,9 mm / 600 mm, 1/4"x1,8 mm / 300 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 50x30x3 mm / 1.200 mm, 40x20x2 mm / 800 mm
Form tube square (section / min. diameter): 40x40x3 mm / 1.200 mm, 30x30x2 mm / 800 mm
Angle leg outside (Querschnitt / min. Durchmesser): 40x40x5 mm / 600 mm, 30x30x4 mm / 300 mm
Angle leg inside (section / min. diameter): 35x35x5 mm / 600 mm, 30x30x4 mm / 400 mm
Length: 600 mm
Width: 800 mm
Height: 1450 mm
Weight: 220 kg
5
Metal working and machine toolsSheet metal working machinesBending machines
Shaft diameter: 50
Rolls diameter: 155 mm
Driven rolls: 2
Motor power: 1.5 kW
Speed: 4 m/min
Flat steel vertical position (section / min. diameter): 60x10 mm / 500 mm, 40x10 mm / 400 mm
Flat steel horizontal position (section / min. diameter): 100x15 mm / 450 mm, 60 x 10 mm / 350 mm
Square bar (section / min. diameter): 35x35 mm / 900 mm, 20x20 mm / 300 mm
Round bar (section / min. diameter): Ø 35 mm / 600 mm, Ø 30 mm / 400 mm
Tube (section / min. diameter): Ø 70x2 mm / 1.000 mm, Ø 30x2 mm / 500 mm, 2"x2,9 mm / 1.000 mm, 1"x2,3 mm / 350 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 70x30x2 mm / 1.200 mm, 50x40x3 mm / 1.200 mm
Form tube square (section / min. diameter): 50x50x3 mm / 1.700 mm, 40x40x3 mm / 600 mm
Angle leg outside (Querschnitt / min. Durchmesser): 50x50x5 mm / 800 mm, 40x40x5 mm / 600 mm
Angle leg inside (section / min. diameter): 50x50x6 mm / 1.000 mm, 30x30x3 mm / 500 mm
Length: 1050 mm
Width: 750 mm
Height: 1450 mm
Weight: 390 kg
Shaft diameter: 50
Rolls diameter: 155 mm
Driven rolls: 2
Motor power: 1.5 kW
Speed: 4 m/min
Flat steel vertical position (section / min. diameter): 60x10 mm / 500 mm, 40x10 mm / 400 mm
Flat steel horizontal position (section / min. diameter): 100x15 mm / 450 mm, 60 x 10 mm / 350 mm
Square bar (section / min. diameter): 35x35 mm / 900 mm, 20x20 mm / 300 mm
Round bar (section / min. diameter): Ø 35 mm / 600 mm, Ø 30 mm / 400 mm
Tube (section / min. diameter): Ø 70x2 mm / 1.000 mm, Ø 30x2 mm / 500 mm, 2"x2,9 mm / 1.000 mm, 1"x2,3 mm / 350 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 70x30x2 mm / 1.200 mm, 50x40x3 mm / 1.200 mm
Form tube square (section / min. diameter): 50x50x3 mm / 1.700 mm, 40x40x3 mm / 600 mm
Angle leg outside (Querschnitt / min. Durchmesser): 50x50x5 mm / 800 mm, 40x40x5 mm / 600 mm
Angle leg inside (section / min. diameter): 50x50x6 mm / 1.000 mm, 30x30x3 mm / 500 mm
Length: 1050 mm
Width: 750 mm
Height: 1450 mm
Weight: 390 kg
Rolls diameter: 155 mm
Driven rolls: 2
Motor power: 1.5 kW
Speed: 4 m/min
Flat steel vertical position (section / min. diameter): 60x10 mm / 500 mm, 40x10 mm / 400 mm
Flat steel horizontal position (section / min. diameter): 100x15 mm / 450 mm, 60 x 10 mm / 350 mm
Square bar (section / min. diameter): 35x35 mm / 900 mm, 20x20 mm / 300 mm
Round bar (section / min. diameter): Ø 35 mm / 600 mm, Ø 30 mm / 400 mm
Tube (section / min. diameter): Ø 70x2 mm / 1.000 mm, Ø 30x2 mm / 500 mm, 2"x2,9 mm / 1.000 mm, 1"x2,3 mm / 350 mm
Form tube vertical position (Querschnitt / min. Durchmesser): 70x30x2 mm / 1.200 mm, 50x40x3 mm / 1.200 mm
Form tube square (section / min. diameter): 50x50x3 mm / 1.700 mm, 40x40x3 mm / 600 mm
Angle leg outside (Querschnitt / min. Durchmesser): 50x50x5 mm / 800 mm, 40x40x5 mm / 600 mm
Angle leg inside (section / min. diameter): 50x50x6 mm / 1.000 mm, 30x30x3 mm / 500 mm
Length: 1050 mm
Width: 750 mm
Height: 1450 mm
Weight: 390 kg
Woodworking machineryExhaust systemsDeduster
Anschlußdurchmesser: . mmSaugleistung: 6.500 m³/hUnterdruck: max. ca. 3.400 paFilterfläche: 80 m²Anschluß: 400 VFrequenz: 50 HzAntrieb: 5,5 kWLuftmenge: max. ca. 8.100 m³/hAbmessungen: ca. 1400x800x2910 BxTxH mm
Anschlußdurchmesser: . mm
Saugleistung: 6.500 m³/h
Unterdruck: max. ca. 3.400 pa
Filterfläche: 80 m²
Anschluß: 400 V
Frequenz: 50 Hz
Antrieb: 5,5 kW
Luftmenge: max. ca. 8.100 m³/h
Abmessungen: ca. 1400x800x2910 BxTxH mm
Saugleistung: 6.500 m³/h
Unterdruck: max. ca. 3.400 pa
Filterfläche: 80 m²
Anschluß: 400 V
Frequenz: 50 Hz
Antrieb: 5,5 kW
Luftmenge: max. ca. 8.100 m³/h
Abmessungen: ca. 1400x800x2910 BxTxH mm
10
Metal working and machine toolsDrilling machines and boring millsTable boring mills
Spindeldurchmesser: 125 mmx-Weg: 2000 mmy-Weg: 1100 mmz-Weg: SK 50 mmSpindelaufnahme: Philips 2500Digitalanzeige: PfillipsDrehzahl: 925 U/minSpindelhub: 800 mmTisch: 1000x1400 mmGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Spindeldurchmesser: 125 mm
x-Weg: 2000 mm
y-Weg: 1100 mm
z-Weg: SK 50 mm
Spindelaufnahme: Philips 2500
Digitalanzeige: Pfillips
Drehzahl: 925 U/min
Spindelhub: 800 mm
Tisch: 1000x1400 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
x-Weg: 2000 mm
y-Weg: 1100 mm
z-Weg: SK 50 mm
Spindelaufnahme: Philips 2500
Digitalanzeige: Pfillips
Drehzahl: 925 U/min
Spindelhub: 800 mm
Tisch: 1000x1400 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
12
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 18587
Manufacturer: FERROMATIK MILACRON
Year of construction: 2001
Clamping unit
Clamping force: 200 ton
Opening stroke: 750 mm
Distance between tie bars: 560 x 560 mm
Mould height min.: 300 mm
Opening width: 1050 mm
Platen size (h x v): 830 x 830 mm
Injection unit
Screw diameter: 50 mm
Injection volume: 441 cm³
Shot weight: 395 g
Injection pressure: 2268 bar
Measurements and weight
Dimensions: 6,9 x 2,0 x 2,6 m
Machine weight: 13000 kg
Further information:
FERROMATIK MILACRON K-TEC 200S – Developed for High-Speed Thin-Wall Production
The FERROMATIK MILACRON K-TEC series was specially developed for thin-wall products, high-speed cycles and precision injection moulding applications.
One of the most important features of this machine is its nitrogen-supported hydraulic accumulator system. This technology enables extremely high injection speeds and ensures fast and balanced mould filling, especially for thin-wall applications.
The K-TEC series is especially preferred for:
• Thin-wall packaging products
• Technical parts with fine surface details
• Lid and container production
• High-flow applications
• High-speed serial production processes
Advantages of the nitrogen-supported system:
• Extremely fast injection performance
• More stable pressure control
• Better reproduction of fine details
• Improved filling of thin-wall products
• Shorter cycle times
• High process stability
The K-TEC series is also known for:
• High repeatability
• Sensitive mould protection
• Low cycle times
• Long-lasting mechanical construction
• Suitability for heavy industrial operating conditions
The machine was actively running in production until it was removed from operation and was working without problems until the very end.
Especially for manufacturers of thin-wall products, this machine still represents a powerful and professional production solution.
Ref. no.: 18587
Manufacturer: FERROMATIK MILACRON
Year of construction: 2001
Clamping unit
Clamping force: 200 ton
Opening stroke: 750 mm
Distance between tie bars: 560 x 560 mm
Mould height min.: 300 mm
Opening width: 1050 mm
Platen size (h x v): 830 x 830 mm
Injection unit
Screw diameter: 50 mm
Injection volume: 441 cm³
Shot weight: 395 g
Injection pressure: 2268 bar
Measurements and weight
Dimensions: 6,9 x 2,0 x 2,6 m
Machine weight: 13000 kg
Further information:
FERROMATIK MILACRON K-TEC 200S – Developed for High-Speed Thin-Wall Production
The FERROMATIK MILACRON K-TEC series was specially developed for thin-wall products, high-speed cycles and precision injection moulding applications.
One of the most important features of this machine is its nitrogen-supported hydraulic accumulator system. This technology enables extremely high injection speeds and ensures fast and balanced mould filling, especially for thin-wall applications.
The K-TEC series is especially preferred for:
• Thin-wall packaging products
• Technical parts with fine surface details
• Lid and container production
• High-flow applications
• High-speed serial production processes
Advantages of the nitrogen-supported system:
• Extremely fast injection performance
• More stable pressure control
• Better reproduction of fine details
• Improved filling of thin-wall products
• Shorter cycle times
• High process stability
The K-TEC series is also known for:
• High repeatability
• Sensitive mould protection
• Low cycle times
• Long-lasting mechanical construction
• Suitability for heavy industrial operating conditions
The machine was actively running in production until it was removed from operation and was working without problems until the very end.
Especially for manufacturers of thin-wall products, this machine still represents a powerful and professional production solution.
Manufacturer: FERROMATIK MILACRON
Year of construction: 2001
Clamping unit
Clamping force: 200 ton
Opening stroke: 750 mm
Distance between tie bars: 560 x 560 mm
Mould height min.: 300 mm
Opening width: 1050 mm
Platen size (h x v): 830 x 830 mm
Injection unit
Screw diameter: 50 mm
Injection volume: 441 cm³
Shot weight: 395 g
Injection pressure: 2268 bar
Measurements and weight
Dimensions: 6,9 x 2,0 x 2,6 m
Machine weight: 13000 kg
Further information:
FERROMATIK MILACRON K-TEC 200S – Developed for High-Speed Thin-Wall Production
The FERROMATIK MILACRON K-TEC series was specially developed for thin-wall products, high-speed cycles and precision injection moulding applications.
One of the most important features of this machine is its nitrogen-supported hydraulic accumulator system. This technology enables extremely high injection speeds and ensures fast and balanced mould filling, especially for thin-wall applications.
The K-TEC series is especially preferred for:
• Thin-wall packaging products
• Technical parts with fine surface details
• Lid and container production
• High-flow applications
• High-speed serial production processes
Advantages of the nitrogen-supported system:
• Extremely fast injection performance
• More stable pressure control
• Better reproduction of fine details
• Improved filling of thin-wall products
• Shorter cycle times
• High process stability
The K-TEC series is also known for:
• High repeatability
• Sensitive mould protection
• Low cycle times
• Long-lasting mechanical construction
• Suitability for heavy industrial operating conditions
The machine was actively running in production until it was removed from operation and was working without problems until the very end.
Especially for manufacturers of thin-wall products, this machine still represents a powerful and professional production solution.
12
Food machinesMeat processing
Atlas Copco ZT30 Air compressor, Serial: AIF065085, 2000, oil free air cooled screw compressor, operating pressure 8.6Bar, compressor output 69 l/s, motor 30Kw, comes with Ultrafilter International dryer model: HLALD0225 and Abbott air tank
Atlas Copco ZT30 Air compressor, Serial: AIF065085, 2000, oil free air cooled screw compressor, operating pressure 8.6Bar, compressor output 69 l/s, motor 30Kw, comes with Ultrafilter International dryer model: HLALD0225 and Abbott air tank
12
Food machinesMeat processing
Atlas Copco ZT30 Air compressor, Serial: AIF065086, 2000, oil free air cooled screw compressor, operating pressure 8.6Bar, compressor output 69 l/s, motor 30Kw, comes with Ultrafilter International dryer model: HLALD0225 and Abbott air tank
Atlas Copco ZT30 Air compressor, Serial: AIF065086, 2000, oil free air cooled screw compressor, operating pressure 8.6Bar, compressor output 69 l/s, motor 30Kw, comes with Ultrafilter International dryer model: HLALD0225 and Abbott air tank
8
Food machinesCatering technologyWashing machines
IWM SAN100 SP Sanitiser tunnel, 2010, stainless, aperture 600mm x 600mm, belt dimensions 1800mm x 600mm, with recirculation tank, filter, level sensor, 3Ph
IWM SAN100 SP Sanitiser tunnel, 2010, stainless, aperture 600mm x 600mm, belt dimensions 1800mm x 600mm, with recirculation tank, filter, level sensor, 3Ph
12
Food machinesOther
Allfill SHA15 Auger filler , Refurbed in 2023, touch screen control, stainless, auger filler variable speed or continuous fill, 75Kg stainless hopper with 50mm stainless screw discharge, with level detection, with foot pedal, Previously used inline with elevator screw for filling the hopper, 3Ph
Allfill SHA15 Auger filler , Refurbed in 2023, touch screen control, stainless, auger filler variable speed or continuous fill, 75Kg stainless hopper with 50mm stainless screw discharge, with level detection, with foot pedal, Previously used inline with elevator screw for filling the hopper, 3Ph
10
Food machinesMeat processing
Longwood D screen Fine screen, 2010, Dscreen simple design, operation and maintenance make it the ideal choice for reliable stand alone water filtration, fully enclosed unit, self cleaning screen, 0.8mm screens, Length 1200mm, width 1023mm, 0.37Kw motor, two available
Longwood D screen Fine screen, 2010, Dscreen simple design, operation and maintenance make it the ideal choice for reliable stand alone water filtration, fully enclosed unit, self cleaning screen, 0.8mm screens, Length 1200mm, width 1023mm, 0.37Kw motor, two available
1
Metal working and machine toolsSheet metal working machinesSection steel shears
Punching power: 110 ton
Throat depth: 610 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 420/20 bzw. 28/28 mm
Stroke: 80 mm
Strokes: 28 1/min
Flat steel: 600x15 / 400x20 mm
Angle steel: 152x152x13 mm
Round / square steel: 50 mm
Notcher: 13x52x90 mm
Motor: 9 kW
Length: 2690 mm
Width: 1400 mm
Height: 2200 mm
Weight: 3300 kg
Punching power: 110 ton
Throat depth: 610 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 420/20 bzw. 28/28 mm
Stroke: 80 mm
Strokes: 28 1/min
Flat steel: 600x15 / 400x20 mm
Angle steel: 152x152x13 mm
Round / square steel: 50 mm
Notcher: 13x52x90 mm
Motor: 9 kW
Length: 2690 mm
Width: 1400 mm
Height: 2200 mm
Weight: 3300 kg
Throat depth: 610 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 420/20 bzw. 28/28 mm
Stroke: 80 mm
Strokes: 28 1/min
Flat steel: 600x15 / 400x20 mm
Angle steel: 152x152x13 mm
Round / square steel: 50 mm
Notcher: 13x52x90 mm
Motor: 9 kW
Length: 2690 mm
Width: 1400 mm
Height: 2200 mm
Weight: 3300 kg
1
Metal working and machine toolsSheet metal working machinesSection steel shears
Punching power: 55 ton
Throat depth: 250 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/10 mm
Stroke: 20 mm
Strokes: 37 1/min
Flat steel: 300x15 mm
Angle steel: 120x10 mm
Round / square steel: 40 mm
Notcher: 10 mm
Motor: 5 kW
Length: 1670 mm
Width: 1160 mm
Height: 2090 mm
Weight: 1390 kg
Punching power: 55 ton
Throat depth: 250 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/10 mm
Stroke: 20 mm
Strokes: 37 1/min
Flat steel: 300x15 mm
Angle steel: 120x10 mm
Round / square steel: 40 mm
Notcher: 10 mm
Motor: 5 kW
Length: 1670 mm
Width: 1160 mm
Height: 2090 mm
Weight: 1390 kg
Throat depth: 250 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/10 mm
Stroke: 20 mm
Strokes: 37 1/min
Flat steel: 300x15 mm
Angle steel: 120x10 mm
Round / square steel: 40 mm
Notcher: 10 mm
Motor: 5 kW
Length: 1670 mm
Width: 1160 mm
Height: 2090 mm
Weight: 1390 kg
10
Metal working and machine toolsSheet metal working machinesSection steel shears
Punching power: 110 ton
Throat depth: 300 mm
Number of stations: 5
Cylinder: 2
Max. diameter at sheet thickness (mild steel): 40x20 (28x28) mm
Stroke: 80 mm
Strokes: 17 1/min
Flat steel: 600x15 (400x20) mm
Blade length: 605 mm
Angle steel: 152x152x13 mm
Round / square steel: 50/50 mm
Notcher: 90x52x13 mm
Motor: 5 kW
Length: 2130 mm
Width: 1200 mm
Height: 2200 mm
Weight: 2500 kg
Punching power: 110 ton
Throat depth: 300 mm
Number of stations: 5
Cylinder: 2
Max. diameter at sheet thickness (mild steel): 40x20 (28x28) mm
Stroke: 80 mm
Strokes: 17 1/min
Flat steel: 600x15 (400x20) mm
Blade length: 605 mm
Angle steel: 152x152x13 mm
Round / square steel: 50/50 mm
Notcher: 90x52x13 mm
Motor: 5 kW
Length: 2130 mm
Width: 1200 mm
Height: 2200 mm
Weight: 2500 kg
Throat depth: 300 mm
Number of stations: 5
Cylinder: 2
Max. diameter at sheet thickness (mild steel): 40x20 (28x28) mm
Stroke: 80 mm
Strokes: 17 1/min
Flat steel: 600x15 (400x20) mm
Blade length: 605 mm
Angle steel: 152x152x13 mm
Round / square steel: 50/50 mm
Notcher: 90x52x13 mm
Motor: 5 kW
Length: 2130 mm
Width: 1200 mm
Height: 2200 mm
Weight: 2500 kg
14
Metal working and machine toolsSanding machinesInternal grinding machines
Internal grinding diameter min.: 1 mm
Internal grinding diameter max: 50 mm
Grinding length: 200 mm
Centre height: 132 mm
Tool spindle speed: 150 - 1.500 rpm
Table speed: continuous adjustment up to 10
Dressing device: yes
Spindle speed: 16.500 - 120.000 rpm
Internal grinding spindle: 16.500, 22.000, 33.000 rpm
Paper belt filter: yes
Total power: 3 kW
Weight of machine: 2000 kg
Space requirement (W x D x H): 1,8 x 1,1 x 1,8 m
Condition: good
Well-maintained machine from a German automobile manufacturer
Accessory: Documentation, 1 drawer cabinet with accessories --> see pictures, 1 pallet of grinding stones --> see pictures
Internal grinding diameter min.: 1 mm
Internal grinding diameter max: 50 mm
Grinding length: 200 mm
Centre height: 132 mm
Tool spindle speed: 150 - 1.500 rpm
Table speed: continuous adjustment up to 10
Dressing device: yes
Spindle speed: 16.500 - 120.000 rpm
Internal grinding spindle: 16.500, 22.000, 33.000 rpm
Paper belt filter: yes
Total power: 3 kW
Weight of machine: 2000 kg
Space requirement (W x D x H): 1,8 x 1,1 x 1,8 m
Condition: good
Well-maintained machine from a German automobile manufacturer
Accessory: Documentation, 1 drawer cabinet with accessories --> see pictures, 1 pallet of grinding stones --> see pictures
Internal grinding diameter max: 50 mm
Grinding length: 200 mm
Centre height: 132 mm
Tool spindle speed: 150 - 1.500 rpm
Table speed: continuous adjustment up to 10
Dressing device: yes
Spindle speed: 16.500 - 120.000 rpm
Internal grinding spindle: 16.500, 22.000, 33.000 rpm
Paper belt filter: yes
Total power: 3 kW
Weight of machine: 2000 kg
Space requirement (W x D x H): 1,8 x 1,1 x 1,8 m
Condition: good
Well-maintained machine from a German automobile manufacturer
Accessory: Documentation, 1 drawer cabinet with accessories --> see pictures, 1 pallet of grinding stones --> see pictures
5
Metal working and machine toolsDrilling machines and boring millsPlate boring mills
Spindeldurchmesser: 125 mmx-Weg: 2500 mmy-Weg: 1900 mmw-Achse: 1100 mmPlanschieberweg: mmBohrwerksdrehtisch:: 1800x1300 mmTisch verstellbar: 1000 mmDigitalanzeige: PfillipsGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Spindeldurchmesser: 125 mm
x-Weg: 2500 mm
y-Weg: 1900 mm
w-Achse: 1100 mm
Planschieberweg: mm
Bohrwerksdrehtisch:: 1800x1300 mm
Tisch verstellbar: 1000 mm
Digitalanzeige: Pfillips
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
x-Weg: 2500 mm
y-Weg: 1900 mm
w-Achse: 1100 mm
Planschieberweg: mm
Bohrwerksdrehtisch:: 1800x1300 mm
Tisch verstellbar: 1000 mm
Digitalanzeige: Pfillips
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
9
Metal working and machine toolsMachining centersUniversal machining centers
x-Weg: 700 mmy-Weg: 600 mmz-Weg: 600 mmTischfläche: 630 mmDrehtisch: 360 GradSchwenktischwinkel min./max.: 45/20 GradDrehzahl: 6300 U/minSteuerung: PfilipsTyp: CNC 432Spindelaufnahme ISO: 40Gesamtleistungsbedarf: 27 KVAMaschinengewicht ca.: 5,8 tRaumbedarf ca.: 4,1x2,3x2,4 m
x-Weg: 700 mm
y-Weg: 600 mm
z-Weg: 600 mm
Tischfläche: 630 mm
Drehtisch: 360 Grad
Schwenktischwinkel min./max.: 45/20 Grad
Drehzahl: 6300 U/min
Steuerung: Pfilips
Typ: CNC 432
Spindelaufnahme ISO: 40
Gesamtleistungsbedarf: 27 KVA
Maschinengewicht ca.: 5,8 t
Raumbedarf ca.: 4,1x2,3x2,4 m
y-Weg: 600 mm
z-Weg: 600 mm
Tischfläche: 630 mm
Drehtisch: 360 Grad
Schwenktischwinkel min./max.: 45/20 Grad
Drehzahl: 6300 U/min
Steuerung: Pfilips
Typ: CNC 432
Spindelaufnahme ISO: 40
Gesamtleistungsbedarf: 27 KVA
Maschinengewicht ca.: 5,8 t
Raumbedarf ca.: 4,1x2,3x2,4 m
8
Metal working and machine toolsLathesCNC lathes
Drehdurchmesser: 500 mmDrehlänge: 1100 mmSteuerung: Pfillips 432Drehdurchmesser über Support: 420 mmSpindeldrehzahlen: 3000 U/minSpindeldurchlass: 82 mmWerkzeugwechsler: 12Werkzeugaufnahme: VDI 40Gesamtleistungsbedarf: kWMaschinengewicht ca.: 5,7 tRaumbedarf ca.: m
Drehdurchmesser: 500 mm
Drehlänge: 1100 mm
Steuerung: Pfillips 432
Drehdurchmesser über Support: 420 mm
Spindeldrehzahlen: 3000 U/min
Spindeldurchlass: 82 mm
Werkzeugwechsler: 12
Werkzeugaufnahme: VDI 40
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: 5,7 t
Raumbedarf ca.: m
Drehlänge: 1100 mm
Steuerung: Pfillips 432
Drehdurchmesser über Support: 420 mm
Spindeldrehzahlen: 3000 U/min
Spindeldurchlass: 82 mm
Werkzeugwechsler: 12
Werkzeugaufnahme: VDI 40
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: 5,7 t
Raumbedarf ca.: m