6
Metal working and machine toolsLathes
Swing over bed: 325 mm
Distance between centers: 1000 mm
Centre height: 165 mm
Spindle bore: 32 mm
swing over cross slide: 190 mm
Width of bed: 200 mm
Spindle nose / DIN55027: 5
Spindle taper: 4 M
Spindle speed steps: 12
Spindle revs: Array rpm
Number of feeds: 48
Longitudinal feed range: 0.006 - 1.77 mm/r
Cross feed range: 0.003 - 0.885 mm/r
Metric thread range: 0.1 - 28 mm
Inch thread range: Array Tpi
Module thread range: 0.1 - 1.75
DP thread range: Array
Cross slide travel: 150 mm
Top slide travel: 95 mm
Tailstock quill diameter: 40 mm
Tailstock quill taper: 3 MK
Tailstock travel: 100 mm
Motor power: 2.2 kW
Length: 2150 mm
Width: 950 mm
Height: 1350 mm
Weight: 770 kg
Swing over bed: 325 mm
Distance between centers: 1000 mm
Centre height: 165 mm
Spindle bore: 32 mm
swing over cross slide: 190 mm
Width of bed: 200 mm
Spindle nose / DIN55027: 5
Spindle taper: 4 M
Spindle speed steps: 12
Spindle revs: Array rpm
Number of feeds: 48
Longitudinal feed range: 0.006 - 1.77 mm/r
Cross feed range: 0.003 - 0.885 mm/r
Metric thread range: 0.1 - 28 mm
Inch thread range: Array Tpi
Module thread range: 0.1 - 1.75
DP thread range: Array
Cross slide travel: 150 mm
Top slide travel: 95 mm
Tailstock quill diameter: 40 mm
Tailstock quill taper: 3 MK
Tailstock travel: 100 mm
Motor power: 2.2 kW
Length: 2150 mm
Width: 950 mm
Height: 1350 mm
Weight: 770 kg
Distance between centers: 1000 mm
Centre height: 165 mm
Spindle bore: 32 mm
swing over cross slide: 190 mm
Width of bed: 200 mm
Spindle nose / DIN55027: 5
Spindle taper: 4 M
Spindle speed steps: 12
Spindle revs: Array rpm
Number of feeds: 48
Longitudinal feed range: 0.006 - 1.77 mm/r
Cross feed range: 0.003 - 0.885 mm/r
Metric thread range: 0.1 - 28 mm
Inch thread range: Array Tpi
Module thread range: 0.1 - 1.75
DP thread range: Array
Cross slide travel: 150 mm
Top slide travel: 95 mm
Tailstock quill diameter: 40 mm
Tailstock quill taper: 3 MK
Tailstock travel: 100 mm
Motor power: 2.2 kW
Length: 2150 mm
Width: 950 mm
Height: 1350 mm
Weight: 770 kg
1
Metal working and machine toolsSheet metal working machinesSection steel shears
Punching power: 80 ton
Throat depth: 500 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/14 bzw. 24/24 mm
Stroke: 70 mm
Strokes: 40 1/min
Flat steel: 450x15 / 300x20 mm
Angle steel: 130x130x13 mm
Round / square steel: 45 mm
Notcher: 12x52x90 mm
Motor: 9 kW
Length: 2310 mm
Width: 1200 mm
Height: 2050 mm
Weight: 2400 kg
Punching power: 80 ton
Throat depth: 500 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/14 bzw. 24/24 mm
Stroke: 70 mm
Strokes: 40 1/min
Flat steel: 450x15 / 300x20 mm
Angle steel: 130x130x13 mm
Round / square steel: 45 mm
Notcher: 12x52x90 mm
Motor: 9 kW
Length: 2310 mm
Width: 1200 mm
Height: 2050 mm
Weight: 2400 kg
Throat depth: 500 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/14 bzw. 24/24 mm
Stroke: 70 mm
Strokes: 40 1/min
Flat steel: 450x15 / 300x20 mm
Angle steel: 130x130x13 mm
Round / square steel: 45 mm
Notcher: 12x52x90 mm
Motor: 9 kW
Length: 2310 mm
Width: 1200 mm
Height: 2050 mm
Weight: 2400 kg
5
Metal working and machine toolsSheet metal working machinesSection steel shears
Punching power: 80 ton
Throat depth: 300 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/14 bzw. 24/24 mm
Stroke: 70 mm
Strokes: 40 1/min
Flat steel: 450x15 / 300x20 mm
Angle steel: 130x130x13 mm
Round / square steel: 45 mm
Notcher: 12x52x90 mm
Motor: 9 kW
Length: 2310 mm
Width: 1200 mm
Height: 2050 mm
Weight: 2070 kg
Punching power: 80 ton
Throat depth: 300 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/14 bzw. 24/24 mm
Stroke: 70 mm
Strokes: 40 1/min
Flat steel: 450x15 / 300x20 mm
Angle steel: 130x130x13 mm
Round / square steel: 45 mm
Notcher: 12x52x90 mm
Motor: 9 kW
Length: 2310 mm
Width: 1200 mm
Height: 2050 mm
Weight: 2070 kg
Throat depth: 300 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/14 bzw. 24/24 mm
Stroke: 70 mm
Strokes: 40 1/min
Flat steel: 450x15 / 300x20 mm
Angle steel: 130x130x13 mm
Round / square steel: 45 mm
Notcher: 12x52x90 mm
Motor: 9 kW
Length: 2310 mm
Width: 1200 mm
Height: 2050 mm
Weight: 2070 kg
1
Metal working and machine toolsSheet metal working machinesSection steel shears
Punching power: 55 ton
Throat depth: 500 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/10 bzw. 20/20 mm
Stroke: 20 mm
Strokes: 37 1/min
Flat steel: 300x15 / 200x20 mm
Notcher: 10x42x90 mm
Motor: 5 kW
Length: 2100 mm
Width: 1160 mm
Height: 2090 mm
Weight: 1750 kg
Punching power: 55 ton
Throat depth: 500 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/10 bzw. 20/20 mm
Stroke: 20 mm
Strokes: 37 1/min
Flat steel: 300x15 / 200x20 mm
Notcher: 10x42x90 mm
Motor: 5 kW
Length: 2100 mm
Width: 1160 mm
Height: 2090 mm
Weight: 1750 kg
Throat depth: 500 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/10 bzw. 20/20 mm
Stroke: 20 mm
Strokes: 37 1/min
Flat steel: 300x15 / 200x20 mm
Notcher: 10x42x90 mm
Motor: 5 kW
Length: 2100 mm
Width: 1160 mm
Height: 2090 mm
Weight: 1750 kg
1
Metal working and machine toolsSheet metal working machinesSection steel shears
Punching power: 36 ton
Throat depth: 170 mm
Number of stations: 3
Max. diameter at sheet thickness (mild steel): 27x10 mm
Stroke: 15 mm
Strokes: 24 1/min
Flat steel: 350x6 mm
Angle steel: 80x8 mm
Motor: 2.2 kW
Length: 1100 mm
Width: 800 mm
Height: 1400 mm
Weight: 485 kg
Punching power: 36 ton
Throat depth: 170 mm
Number of stations: 3
Max. diameter at sheet thickness (mild steel): 27x10 mm
Stroke: 15 mm
Strokes: 24 1/min
Flat steel: 350x6 mm
Angle steel: 80x8 mm
Motor: 2.2 kW
Length: 1100 mm
Width: 800 mm
Height: 1400 mm
Weight: 485 kg
Throat depth: 170 mm
Number of stations: 3
Max. diameter at sheet thickness (mild steel): 27x10 mm
Stroke: 15 mm
Strokes: 24 1/min
Flat steel: 350x6 mm
Angle steel: 80x8 mm
Motor: 2.2 kW
Length: 1100 mm
Width: 800 mm
Height: 1400 mm
Weight: 485 kg
3
Metal working and machine toolsSheet metal working machinesSection steel shears
Punching power: 85 ton
Throat depth: 500 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/15 bzw. 24x24 mm
Flat steel: 450x15 / 450x18 mm
Blade length: 475 mm
Angle steel: 130x130x13 mm
Round / square steel: 45/40 mm
Notcher: 12 mm
Bending unit: 200x12 mm
Motor: 9.2 kW
Length: 2300 mm
Width: 1200 mm
Height: 2100 mm
Weight: 2400 kg
Punching power: 85 ton
Throat depth: 500 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/15 bzw. 24x24 mm
Flat steel: 450x15 / 450x18 mm
Blade length: 475 mm
Angle steel: 130x130x13 mm
Round / square steel: 45/40 mm
Notcher: 12 mm
Bending unit: 200x12 mm
Motor: 9.2 kW
Length: 2300 mm
Width: 1200 mm
Height: 2100 mm
Weight: 2400 kg
Throat depth: 500 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/15 bzw. 24x24 mm
Flat steel: 450x15 / 450x18 mm
Blade length: 475 mm
Angle steel: 130x130x13 mm
Round / square steel: 45/40 mm
Notcher: 12 mm
Bending unit: 200x12 mm
Motor: 9.2 kW
Length: 2300 mm
Width: 1200 mm
Height: 2100 mm
Weight: 2400 kg
2
Metal working and machine toolsSheet metal working machinesSection steel shears
Punching power: 85 ton
Throat depth: 300 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/15 bzw. 24x24 mm
Flat steel: 450x15 / 450x18 mm
Blade length: 475 mm
Angle steel: 130x130x13 mm
Round / square steel: 45/40 mm
Notcher: 12 mm
Bending unit: 200x12 mm
Motor: 9.2 kW
Length: 2300 mm
Width: 1200 mm
Height: 2100 mm
Weight: 2400 kg
Punching power: 85 ton
Throat depth: 300 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/15 bzw. 24x24 mm
Flat steel: 450x15 / 450x18 mm
Blade length: 475 mm
Angle steel: 130x130x13 mm
Round / square steel: 45/40 mm
Notcher: 12 mm
Bending unit: 200x12 mm
Motor: 9.2 kW
Length: 2300 mm
Width: 1200 mm
Height: 2100 mm
Weight: 2400 kg
Throat depth: 300 mm
Number of stations: 5
Max. diameter at sheet thickness (mild steel): 40/15 bzw. 24x24 mm
Flat steel: 450x15 / 450x18 mm
Blade length: 475 mm
Angle steel: 130x130x13 mm
Round / square steel: 45/40 mm
Notcher: 12 mm
Bending unit: 200x12 mm
Motor: 9.2 kW
Length: 2300 mm
Width: 1200 mm
Height: 2100 mm
Weight: 2400 kg
2
Metal working and machine toolsSheet metal working machinesSection steel shears
Punching power: 60 ton
Throat depth: 500 mm
Number of stations: 5
Cylinder: 2
Max. diameter at sheet thickness (mild steel): 40x11 mm
Strokes: 32 1/min
Flat steel: 350x10 mm
Angle steel: 120x10 mm
Round / square steel: 45/40 mm
Notcher: 100x10 mm
Bending unit: 150x10 mm
Motor: 5.5 kW
Length: 2100 mm
Width: 1400 mm
Height: 2060 mm
Weight: 1750 kg
Punching power: 60 ton
Throat depth: 500 mm
Number of stations: 5
Cylinder: 2
Max. diameter at sheet thickness (mild steel): 40x11 mm
Strokes: 32 1/min
Flat steel: 350x10 mm
Angle steel: 120x10 mm
Round / square steel: 45/40 mm
Notcher: 100x10 mm
Bending unit: 150x10 mm
Motor: 5.5 kW
Length: 2100 mm
Width: 1400 mm
Height: 2060 mm
Weight: 1750 kg
Throat depth: 500 mm
Number of stations: 5
Cylinder: 2
Max. diameter at sheet thickness (mild steel): 40x11 mm
Strokes: 32 1/min
Flat steel: 350x10 mm
Angle steel: 120x10 mm
Round / square steel: 45/40 mm
Notcher: 100x10 mm
Bending unit: 150x10 mm
Motor: 5.5 kW
Length: 2100 mm
Width: 1400 mm
Height: 2060 mm
Weight: 1750 kg
6
Metal working and machine toolsSheet metal working machinesSwivel bending machines
Bending length: 5020 mm
Bending capacity steel 400 N/mm²: 1.5 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.5 mm
No. of stand and tension arm units: 6
No. of driven linkage assemblies: 6
Sheet insertion depth: 1130 mm
Opening of upper beam: 180 mm
Working height: 915 mm
Motor: 4 kW
Max. bending angle: 145 °
Length with electrical shear: 6200 mm
Width: 1435 mm
Height: 1980 mm
Weight: 3200 kg
Bending length: 5020 mm
Bending capacity steel 400 N/mm²: 1.5 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.5 mm
No. of stand and tension arm units: 6
No. of driven linkage assemblies: 6
Sheet insertion depth: 1130 mm
Opening of upper beam: 180 mm
Working height: 915 mm
Motor: 4 kW
Max. bending angle: 145 °
Length with electrical shear: 6200 mm
Width: 1435 mm
Height: 1980 mm
Weight: 3200 kg
Bending capacity steel 400 N/mm²: 1.5 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.5 mm
No. of stand and tension arm units: 6
No. of driven linkage assemblies: 6
Sheet insertion depth: 1130 mm
Opening of upper beam: 180 mm
Working height: 915 mm
Motor: 4 kW
Max. bending angle: 145 °
Length with electrical shear: 6200 mm
Width: 1435 mm
Height: 1980 mm
Weight: 3200 kg
6
Metal working and machine toolsSheet metal working machinesSwivel bending machines
Bending length: 5020 mm
Bending capacity steel 400 N/mm²: 1.25 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.25 mm
No. of stand and tension arm units: 5
No. of driven linkage assemblies: 5
Sheet insertion depth: 1130 mm
Opening of upper beam: 180 mm
Working height: 915 mm
Motor: 3 kW
Max. bending angle: 145 °
Length with electrical shear: 6200 mm
Width: 1435 mm
Height: 1980 mm
Weight: 3000 kg
Bending length: 5020 mm
Bending capacity steel 400 N/mm²: 1.25 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.25 mm
No. of stand and tension arm units: 5
No. of driven linkage assemblies: 5
Sheet insertion depth: 1130 mm
Opening of upper beam: 180 mm
Working height: 915 mm
Motor: 3 kW
Max. bending angle: 145 °
Length with electrical shear: 6200 mm
Width: 1435 mm
Height: 1980 mm
Weight: 3000 kg
Bending capacity steel 400 N/mm²: 1.25 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.25 mm
No. of stand and tension arm units: 5
No. of driven linkage assemblies: 5
Sheet insertion depth: 1130 mm
Opening of upper beam: 180 mm
Working height: 915 mm
Motor: 3 kW
Max. bending angle: 145 °
Length with electrical shear: 6200 mm
Width: 1435 mm
Height: 1980 mm
Weight: 3000 kg
6
Metal working and machine toolsSheet metal working machinesSwivel bending machines
Bending length: 8020 mm
Bending capacity steel 400 N/mm²: 1.5 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.5 - 2 mm
No. of stand and tension arm units: 6
No. of driven linkage assemblies: 6
Sheet insertion depth: 1000 mm
Bending length: 8020 mm
Bending capacity steel 400 N/mm²: 1.5 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.5 - 2 mm
No. of stand and tension arm units: 6
No. of driven linkage assemblies: 6
Sheet insertion depth: 1000 mm
Bending capacity steel 400 N/mm²: 1.5 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.5 - 2 mm
No. of stand and tension arm units: 6
No. of driven linkage assemblies: 6
Sheet insertion depth: 1000 mm
6
Metal working and machine toolsSheet metal working machinesSwivel bending machines
Bending length: 6400 mm
Bending capacity steel 400 N/mm²: 2 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.5 - 2 mm
No. of stand and tension arm units: 7
No. of driven linkage assemblies: 7
Sheet insertion depth: 1000 mm
Bending length: 6400 mm
Bending capacity steel 400 N/mm²: 2 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.5 - 2 mm
No. of stand and tension arm units: 7
No. of driven linkage assemblies: 7
Sheet insertion depth: 1000 mm
Bending capacity steel 400 N/mm²: 2 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.5 - 2 mm
No. of stand and tension arm units: 7
No. of driven linkage assemblies: 7
Sheet insertion depth: 1000 mm
6
Metal working and machine toolsSheet metal working machinesSwivel bending machines
Bending length: 6400 mm
Bending capacity steel 400 N/mm²: 1.5 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.5 - 2 mm
No. of stand and tension arm units: 5
No. of driven linkage assemblies: 5
Sheet insertion depth: 1000 mm
Bending length: 6400 mm
Bending capacity steel 400 N/mm²: 1.5 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.5 - 2 mm
No. of stand and tension arm units: 5
No. of driven linkage assemblies: 5
Sheet insertion depth: 1000 mm
Bending capacity steel 400 N/mm²: 1.5 mm
Bending capacity Alu 190 N/mm²: 2 mm
Cutting capacity electrical shear: 1.5 - 2 mm
No. of stand and tension arm units: 5
No. of driven linkage assemblies: 5
Sheet insertion depth: 1000 mm
6
Metal working and machine toolsSheet metal working machinesSwivel bending machines
Bending length: 5010 mm
Bending capacity steel 400 N/mm²: 1.5 mm
Bending capacity Alu 190 N/mm²: 2 mm
No. of stand and tension arm units: 4
No. of driven linkage assemblies: 4
Sheet insertion depth: 1000 mm
Bending length: 5010 mm
Bending capacity steel 400 N/mm²: 1.5 mm
Bending capacity Alu 190 N/mm²: 2 mm
No. of stand and tension arm units: 4
No. of driven linkage assemblies: 4
Sheet insertion depth: 1000 mm
Bending capacity steel 400 N/mm²: 1.5 mm
Bending capacity Alu 190 N/mm²: 2 mm
No. of stand and tension arm units: 4
No. of driven linkage assemblies: 4
Sheet insertion depth: 1000 mm
4
Metal working and machine toolsSheet metal working machinesPress brakes
pressing capacity: 100 to
Bending length: 2550 mm
Axes: Y1 / Y2 / X axis
Stroke: 265 mm
Inside distance between side frames: 2200 mm
Gap in side frame: 450 mm
Daylight: 530 mm
Power concept: hydraulic
rapid speed Y-axis: 180 mm/s
Working speed Y-axis: 10
Retractionspeed Y-axis: 120
Back gauge speed X-axis: 500
Back gauge speed R-axis: 350 mm/s
Back gauge travel R-axis: 250 mm
Table height: 900 mm
Table width: 104 mm
Oiltank: 100 l
Motor power: 11 kW
Length: 3800 mm
Width: 1670 mm
Height: 2850 mm
Weight: 7800 kg
pressing capacity: 100 to
Bending length: 2550 mm
Axes: Y1 / Y2 / X axis
Stroke: 265 mm
Inside distance between side frames: 2200 mm
Gap in side frame: 450 mm
Daylight: 530 mm
Power concept: hydraulic
rapid speed Y-axis: 180 mm/s
Working speed Y-axis: 10
Retractionspeed Y-axis: 120
Back gauge speed X-axis: 500
Back gauge speed R-axis: 350 mm/s
Back gauge travel R-axis: 250 mm
Table height: 900 mm
Table width: 104 mm
Oiltank: 100 l
Motor power: 11 kW
Length: 3800 mm
Width: 1670 mm
Height: 2850 mm
Weight: 7800 kg
Bending length: 2550 mm
Axes: Y1 / Y2 / X axis
Stroke: 265 mm
Inside distance between side frames: 2200 mm
Gap in side frame: 450 mm
Daylight: 530 mm
Power concept: hydraulic
rapid speed Y-axis: 180 mm/s
Working speed Y-axis: 10
Retractionspeed Y-axis: 120
Back gauge speed X-axis: 500
Back gauge speed R-axis: 350 mm/s
Back gauge travel R-axis: 250 mm
Table height: 900 mm
Table width: 104 mm
Oiltank: 100 l
Motor power: 11 kW
Length: 3800 mm
Width: 1670 mm
Height: 2850 mm
Weight: 7800 kg
1
Metal working and machine toolsSheet metal working machinesFeed straighteners
Sheet Thickness - mild steel: 0.4 - 3.5 mm
Max. sheet width: 200 mm
Max. cross-section: 200 x 3 mm
Feed roll diameter: 80 mm
Feeding speed: 75 m/min
Feeding acceleration: 10 m/s²
Motor torque: 10 Nm
Sheet Thickness - mild steel: 0.4 - 3.5 mm
Max. sheet width: 200 mm
Max. cross-section: 200 x 3 mm
Feed roll diameter: 80 mm
Feeding speed: 75 m/min
Feeding acceleration: 10 m/s²
Motor torque: 10 Nm
Max. sheet width: 200 mm
Max. cross-section: 200 x 3 mm
Feed roll diameter: 80 mm
Feeding speed: 75 m/min
Feeding acceleration: 10 m/s²
Motor torque: 10 Nm
2
Metal working and machine toolsSheet metal working machinesOther
Tube diameter: 3/4" 26,9 mm, 1" 33,7 mm, 1¼" 42,4 mm, 1½" 48,3 mm, 2" 60,3 mm
Max. wall thickness: 5 mm
Max. wall thickness stainless steel: 3 mm
Weight: 87 kg
Tube diameter: 3/4" 26,9 mm, 1" 33,7 mm, 1¼" 42,4 mm, 1½" 48,3 mm, 2" 60,3 mm
Max. wall thickness: 5 mm
Max. wall thickness stainless steel: 3 mm
Weight: 87 kg
Max. wall thickness: 5 mm
Max. wall thickness stainless steel: 3 mm
Weight: 87 kg
2
Metal working and machine toolsSheet metal working machinesBending machines
Bending length: 350 - 2250 mm
Max. sheet length: 2600 mm
Max. sheet width: 1524 mm
Min. bendable width: 150 mm
Max. bending height: 254 mm
Max. bending depth: 50 mm
Max. sheet rotation area: 3300 mm
Bending force: 32 to
Pressure force: 52 to
Sheet thickness (420 N/mm²): 2.5 mm
Sheet thickness (600 N/mm²): 1.8 mm
Sheet thickness (260 N/mm²): 3.5 mm
Min. sheet thickness - mild steel: 0.5 mm
Max. bending angle: 135 °
Bending length: 350 - 2250 mm
Max. sheet length: 2600 mm
Max. sheet width: 1524 mm
Min. bendable width: 150 mm
Max. bending height: 254 mm
Max. bending depth: 50 mm
Max. sheet rotation area: 3300 mm
Bending force: 32 to
Pressure force: 52 to
Sheet thickness (420 N/mm²): 2.5 mm
Sheet thickness (600 N/mm²): 1.8 mm
Sheet thickness (260 N/mm²): 3.5 mm
Min. sheet thickness - mild steel: 0.5 mm
Max. bending angle: 135 °
Max. sheet length: 2600 mm
Max. sheet width: 1524 mm
Min. bendable width: 150 mm
Max. bending height: 254 mm
Max. bending depth: 50 mm
Max. sheet rotation area: 3300 mm
Bending force: 32 to
Pressure force: 52 to
Sheet thickness (420 N/mm²): 2.5 mm
Sheet thickness (600 N/mm²): 1.8 mm
Sheet thickness (260 N/mm²): 3.5 mm
Min. sheet thickness - mild steel: 0.5 mm
Max. bending angle: 135 °
2
Metal working and machine toolsSheet metal working machinesRound rolling machines
Bending length: 1050 mm
Max. bending capacity - mild steel: 5
Upper roll diameter: 130 mm
Bending speed: 3 m/min
Motor power: 2.2 kW
Length: 2200 mm
Width: 750 mm
Height: 1000 mm
Weight: 1200 kg
Bending length: 1050 mm
Max. bending capacity - mild steel: 5
Upper roll diameter: 130 mm
Bending speed: 3 m/min
Motor power: 2.2 kW
Length: 2200 mm
Width: 750 mm
Height: 1000 mm
Weight: 1200 kg
Max. bending capacity - mild steel: 5
Upper roll diameter: 130 mm
Bending speed: 3 m/min
Motor power: 2.2 kW
Length: 2200 mm
Width: 750 mm
Height: 1000 mm
Weight: 1200 kg
2
Metal working and machine toolsSheet metal working machines
Suitable for plates: 1
Suitable for tubes: 1
Max. bevel width: 14 mm
Bevel angle: 30 °
Spindle speed (load-free): 9 rpm
Plate thickness: 6 - 40 mm
Min. plate width: 55 mm
Min. tube inner diameter: 100 mm
Feed speed: 2600 mm/min
Motor: 2.2 kW
Length: 589 mm
Width: 541 mm
Height: 320 mm
Weight: 65 kg
Suitable for plates: 1
Suitable for tubes: 1
Max. bevel width: 14 mm
Bevel angle: 30 °
Spindle speed (load-free): 9 rpm
Plate thickness: 6 - 40 mm
Min. plate width: 55 mm
Min. tube inner diameter: 100 mm
Feed speed: 2600 mm/min
Motor: 2.2 kW
Length: 589 mm
Width: 541 mm
Height: 320 mm
Weight: 65 kg
Suitable for tubes: 1
Max. bevel width: 14 mm
Bevel angle: 30 °
Spindle speed (load-free): 9 rpm
Plate thickness: 6 - 40 mm
Min. plate width: 55 mm
Min. tube inner diameter: 100 mm
Feed speed: 2600 mm/min
Motor: 2.2 kW
Length: 589 mm
Width: 541 mm
Height: 320 mm
Weight: 65 kg
13
Plastic processing machinesInjection molding machinesMulti-component injection molding machines
Ref. no.: 18092
Manufacturer: ENGEL
Year of construction: 2001
Clamping unit
Clamping force: 300 ton
Opening stroke: 855 mm
Platen size (h x v): 1050 x 650 mm
Injection unit
Screw diameter: 60 +35 mm
Injection volume: 735 +135 cm³
Shot weight: 662 + 122 g
Injection pressure: 1834 +1620 bar
Measurements and weight
Dimensions: 7,75 x 2,35 x 2,6 m
Machine weight: 24780 kg
Further information:
ENGEL ES 1350H200W/300HL-2F — 2K Injection Moulding Machine
This machine from the prestigious Austrian manufacturer ENGEL, built in 2001, features a clamping force of 300 tonnes and a true 2K L-configuration in horizontal layout.
Motor and Hydraulic System
The machine is equipped with a powerful electric motor coupled to a high-pressure hydraulic pump group. The electric motor continuously drives the hydraulic pump, providing pressurised oil flow throughout the entire system. This pressurised oil feeds the clamping cylinder, the injection pistons of both units, and the ejector system. The thick red hydraulic hoses visible behind Unit B carry this high-pressure oil flow — both units are supplied via independent hydraulic circuits, allowing Unit A and Unit B to operate simultaneously without influencing each other.
Operating Principle
The two independent injection units are positioned at 90° to each other — in an L-shape. The mould is locked with 300 tonnes of clamping force. Unit A injects the primary material into the mould at 1834 bar. Immediately afterwards, Unit B injects the second material or colour from a 90° angle into the same mould at 1620 bar. The two materials bond at a molecular level inside the mould, cooling is completed and the ejectors push out the finished 2K part as a single piece. No gluing, screwing or assembly is required — two materials emerge as one single part in a single cycle.
Applications
Automotive interior and exterior trim parts, large technical plastic components, parts combining a rigid body with a soft grip surface, two-colour large-surface parts.
Ref. no.: 18092
Manufacturer: ENGEL
Year of construction: 2001
Clamping unit
Clamping force: 300 ton
Opening stroke: 855 mm
Platen size (h x v): 1050 x 650 mm
Injection unit
Screw diameter: 60 +35 mm
Injection volume: 735 +135 cm³
Shot weight: 662 + 122 g
Injection pressure: 1834 +1620 bar
Measurements and weight
Dimensions: 7,75 x 2,35 x 2,6 m
Machine weight: 24780 kg
Further information:
ENGEL ES 1350H200W/300HL-2F — 2K Injection Moulding Machine
This machine from the prestigious Austrian manufacturer ENGEL, built in 2001, features a clamping force of 300 tonnes and a true 2K L-configuration in horizontal layout.
Motor and Hydraulic System
The machine is equipped with a powerful electric motor coupled to a high-pressure hydraulic pump group. The electric motor continuously drives the hydraulic pump, providing pressurised oil flow throughout the entire system. This pressurised oil feeds the clamping cylinder, the injection pistons of both units, and the ejector system. The thick red hydraulic hoses visible behind Unit B carry this high-pressure oil flow — both units are supplied via independent hydraulic circuits, allowing Unit A and Unit B to operate simultaneously without influencing each other.
Operating Principle
The two independent injection units are positioned at 90° to each other — in an L-shape. The mould is locked with 300 tonnes of clamping force. Unit A injects the primary material into the mould at 1834 bar. Immediately afterwards, Unit B injects the second material or colour from a 90° angle into the same mould at 1620 bar. The two materials bond at a molecular level inside the mould, cooling is completed and the ejectors push out the finished 2K part as a single piece. No gluing, screwing or assembly is required — two materials emerge as one single part in a single cycle.
Applications
Automotive interior and exterior trim parts, large technical plastic components, parts combining a rigid body with a soft grip surface, two-colour large-surface parts.
Manufacturer: ENGEL
Year of construction: 2001
Clamping unit
Clamping force: 300 ton
Opening stroke: 855 mm
Platen size (h x v): 1050 x 650 mm
Injection unit
Screw diameter: 60 +35 mm
Injection volume: 735 +135 cm³
Shot weight: 662 + 122 g
Injection pressure: 1834 +1620 bar
Measurements and weight
Dimensions: 7,75 x 2,35 x 2,6 m
Machine weight: 24780 kg
Further information:
ENGEL ES 1350H200W/300HL-2F — 2K Injection Moulding Machine
This machine from the prestigious Austrian manufacturer ENGEL, built in 2001, features a clamping force of 300 tonnes and a true 2K L-configuration in horizontal layout.
Motor and Hydraulic System
The machine is equipped with a powerful electric motor coupled to a high-pressure hydraulic pump group. The electric motor continuously drives the hydraulic pump, providing pressurised oil flow throughout the entire system. This pressurised oil feeds the clamping cylinder, the injection pistons of both units, and the ejector system. The thick red hydraulic hoses visible behind Unit B carry this high-pressure oil flow — both units are supplied via independent hydraulic circuits, allowing Unit A and Unit B to operate simultaneously without influencing each other.
Operating Principle
The two independent injection units are positioned at 90° to each other — in an L-shape. The mould is locked with 300 tonnes of clamping force. Unit A injects the primary material into the mould at 1834 bar. Immediately afterwards, Unit B injects the second material or colour from a 90° angle into the same mould at 1620 bar. The two materials bond at a molecular level inside the mould, cooling is completed and the ejectors push out the finished 2K part as a single piece. No gluing, screwing or assembly is required — two materials emerge as one single part in a single cycle.
Applications
Automotive interior and exterior trim parts, large technical plastic components, parts combining a rigid body with a soft grip surface, two-colour large-surface parts.
11
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 17507
Manufacturer: DEMAG
Year of construction: 1998
Clamping unit
Clamping force: 80 ton
Opening stroke: 450 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 200 mm
Platen size (h x v): 600 x 600 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 168 cm³
Shot weight: 149 g
Injection pressure: 2020 bar
Measurements and weight
Dimensions: 4,1 x 1,4 x 2,0 m
Machine weight: 3700 kg
Ref. no.: 17507
Manufacturer: DEMAG
Year of construction: 1998
Clamping unit
Clamping force: 80 ton
Opening stroke: 450 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 200 mm
Platen size (h x v): 600 x 600 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 168 cm³
Shot weight: 149 g
Injection pressure: 2020 bar
Measurements and weight
Dimensions: 4,1 x 1,4 x 2,0 m
Machine weight: 3700 kg
Manufacturer: DEMAG
Year of construction: 1998
Clamping unit
Clamping force: 80 ton
Opening stroke: 450 mm
Distance between tie bars: 370 x 370 mm
Mould height min.: 200 mm
Platen size (h x v): 600 x 600 mm
Injection unit
Screw diameter: 35 mm
Injection volume: 168 cm³
Shot weight: 149 g
Injection pressure: 2020 bar
Measurements and weight
Dimensions: 4,1 x 1,4 x 2,0 m
Machine weight: 3700 kg
13
Plastic processing machinesInjection molding machinesPlastic injection molding machines
Ref. no.: 16369
Manufacturer: BATTENFELD
Year of construction: 2005
Clamping unit
Clamping force: 75 ton
Opening stroke: 800 mm
Distance between tie bars: 405 x 405 mm
Mould height min.: 150 mm
Mould height max.: 480 mm
Injection unit
Screw diameter: 18 mm
Injection volume: 30 cm³
Shot weight: 27 g
Injection pressure: 2440 bar
Measurements and weight
Dimensions: 4,5 x 1,7 x 2,0 m
Machine weight: 4500 kg
Further information:
BATTENFELD EM 75/120 UNILOG B4
All-Electric Precision Injection Moulding Machine
The BATTENFELD EM 75/120 UNILOG B4 is a high-quality Austrian-made all-electric injection moulding machine. The BATTENFELD EM series was considered one of the most advanced servo-electric machine concepts of its time and was specifically designed for energy-efficient and highly precise production processes.
All major machine movements are driven by modern servo motors, providing:
* very low energy consumption
* high repeatability and precision
* smooth and quiet machine operation
* low maintenance requirements
* stable and accurate production performance
The machine is especially suitable for:
* technical plastic components
* electronic parts
* precision moulded products
* small and medium-sized production runs
Compared to conventional hydraulic machines, the all-electric technology offers significantly improved energy efficiency and process stability.
Equipped with the reliable BATTENFELD UNILOG B4 control system, the machine provides:
* user-friendly operation
* precise process control
* stable cycle times
* accurate servo axis management
The machine has approximately 69,094 operating hours and appears to be in clean and well-maintained condition. The photos clearly show:
* a clean electrical cabinet
* well-maintained mechanical components
* properly kept servo-electric units
* a clean injection unit
The BATTENFELD EM 75/120 UNILOG B4 is a reliable and energy-efficient solution for demanding plastic injection moulding applications.
Ref. no.: 16369
Manufacturer: BATTENFELD
Year of construction: 2005
Clamping unit
Clamping force: 75 ton
Opening stroke: 800 mm
Distance between tie bars: 405 x 405 mm
Mould height min.: 150 mm
Mould height max.: 480 mm
Injection unit
Screw diameter: 18 mm
Injection volume: 30 cm³
Shot weight: 27 g
Injection pressure: 2440 bar
Measurements and weight
Dimensions: 4,5 x 1,7 x 2,0 m
Machine weight: 4500 kg
Further information:
BATTENFELD EM 75/120 UNILOG B4
All-Electric Precision Injection Moulding Machine
The BATTENFELD EM 75/120 UNILOG B4 is a high-quality Austrian-made all-electric injection moulding machine. The BATTENFELD EM series was considered one of the most advanced servo-electric machine concepts of its time and was specifically designed for energy-efficient and highly precise production processes.
All major machine movements are driven by modern servo motors, providing:
* very low energy consumption
* high repeatability and precision
* smooth and quiet machine operation
* low maintenance requirements
* stable and accurate production performance
The machine is especially suitable for:
* technical plastic components
* electronic parts
* precision moulded products
* small and medium-sized production runs
Compared to conventional hydraulic machines, the all-electric technology offers significantly improved energy efficiency and process stability.
Equipped with the reliable BATTENFELD UNILOG B4 control system, the machine provides:
* user-friendly operation
* precise process control
* stable cycle times
* accurate servo axis management
The machine has approximately 69,094 operating hours and appears to be in clean and well-maintained condition. The photos clearly show:
* a clean electrical cabinet
* well-maintained mechanical components
* properly kept servo-electric units
* a clean injection unit
The BATTENFELD EM 75/120 UNILOG B4 is a reliable and energy-efficient solution for demanding plastic injection moulding applications.
Manufacturer: BATTENFELD
Year of construction: 2005
Clamping unit
Clamping force: 75 ton
Opening stroke: 800 mm
Distance between tie bars: 405 x 405 mm
Mould height min.: 150 mm
Mould height max.: 480 mm
Injection unit
Screw diameter: 18 mm
Injection volume: 30 cm³
Shot weight: 27 g
Injection pressure: 2440 bar
Measurements and weight
Dimensions: 4,5 x 1,7 x 2,0 m
Machine weight: 4500 kg
Further information:
BATTENFELD EM 75/120 UNILOG B4
All-Electric Precision Injection Moulding Machine
The BATTENFELD EM 75/120 UNILOG B4 is a high-quality Austrian-made all-electric injection moulding machine. The BATTENFELD EM series was considered one of the most advanced servo-electric machine concepts of its time and was specifically designed for energy-efficient and highly precise production processes.
All major machine movements are driven by modern servo motors, providing:
* very low energy consumption
* high repeatability and precision
* smooth and quiet machine operation
* low maintenance requirements
* stable and accurate production performance
The machine is especially suitable for:
* technical plastic components
* electronic parts
* precision moulded products
* small and medium-sized production runs
Compared to conventional hydraulic machines, the all-electric technology offers significantly improved energy efficiency and process stability.
Equipped with the reliable BATTENFELD UNILOG B4 control system, the machine provides:
* user-friendly operation
* precise process control
* stable cycle times
* accurate servo axis management
The machine has approximately 69,094 operating hours and appears to be in clean and well-maintained condition. The photos clearly show:
* a clean electrical cabinet
* well-maintained mechanical components
* properly kept servo-electric units
* a clean injection unit
The BATTENFELD EM 75/120 UNILOG B4 is a reliable and energy-efficient solution for demanding plastic injection moulding applications.
1
Metal working and machine toolsSanding machinesAccessories and spare parts
Machine spindle for belt drive and direct drive, 2500 rpm, overhauled in 03/03 and no longer used, original packing from GMN, serial no. 280217, used, in full function
Machine spindle for belt drive and direct drive, 2500 rpm, overhauled in 03/03 and no longer used, original packing from GMN, serial no. 280217, used, in full function
4
Metal working and machine toolsMilling machinesAccessories and spare parts
Working Area: 560 x 400 x 32 mm
Reference table/Clamping field, holes with M12 thread, bores diameter 16/12 m, bores diameter 11/18 mm, No. 3R-935-56 02, SN 400 100
Working Area: 560 x 400 x 32 mm
Reference table/Clamping field, holes with M12 thread, bores diameter 16/12 m, bores diameter 11/18 mm, No. 3R-935-56 02, SN 400 100
Reference table/Clamping field, holes with M12 thread, bores diameter 16/12 m, bores diameter 11/18 mm, No. 3R-935-56 02, SN 400 100
9
Metal working and machine toolsWelding machinesRobots
Load capacity: 16 kg
Range working radius: 1550 mm
Control Modul: IRC5 M2004
Robot version: IRB 2400/16 Type B - M2004
Teach Panel: FlexPendant
Remote I/O Unit: DSQC 350A
Number of axes: 6
Total power: 1 kW
Weight of machine: 800 kg
Space requirement (W x D x H): 0,73 x 0,6 x 1,6 m
Condition: very good
Working hour: 37095 h
well-kept robot, usable immediately
Accessory: Documentation, all cables
Load capacity: 16 kg
Range working radius: 1550 mm
Control Modul: IRC5 M2004
Robot version: IRB 2400/16 Type B - M2004
Teach Panel: FlexPendant
Remote I/O Unit: DSQC 350A
Number of axes: 6
Total power: 1 kW
Weight of machine: 800 kg
Space requirement (W x D x H): 0,73 x 0,6 x 1,6 m
Condition: very good
Working hour: 37095 h
well-kept robot, usable immediately
Accessory: Documentation, all cables
Range working radius: 1550 mm
Control Modul: IRC5 M2004
Robot version: IRB 2400/16 Type B - M2004
Teach Panel: FlexPendant
Remote I/O Unit: DSQC 350A
Number of axes: 6
Total power: 1 kW
Weight of machine: 800 kg
Space requirement (W x D x H): 0,73 x 0,6 x 1,6 m
Condition: very good
Working hour: 37095 h
well-kept robot, usable immediately
Accessory: Documentation, all cables
13
Metal working and machine toolsSurface finishing
Ultrasonic power: 8,4 kW
Component weight max.: 5000 kg
Volume: 2000 ltr
Heating capacity: 51 kW
Internal usable dimensions L/W/H: 1600/ 1000/ 1250 mm
Space requirement (W x D x H): 12 x 3,2 x 2,1 m
Total power: 60 kW
Condition: very good
mold cleaning for plastic injection molding, extrusion, elastomers, die casting, core boxes, molds, well-kept facility, was hardly in use
Ultrasonic power: 8,4 kW
Component weight max.: 5000 kg
Volume: 2000 ltr
Heating capacity: 51 kW
Internal usable dimensions L/W/H: 1600/ 1000/ 1250 mm
Space requirement (W x D x H): 12 x 3,2 x 2,1 m
Total power: 60 kW
Condition: very good
mold cleaning for plastic injection molding, extrusion, elastomers, die casting, core boxes, molds, well-kept facility, was hardly in use
Component weight max.: 5000 kg
Volume: 2000 ltr
Heating capacity: 51 kW
Internal usable dimensions L/W/H: 1600/ 1000/ 1250 mm
Space requirement (W x D x H): 12 x 3,2 x 2,1 m
Total power: 60 kW
Condition: very good
mold cleaning for plastic injection molding, extrusion, elastomers, die casting, core boxes, molds, well-kept facility, was hardly in use
8
Werkstückdurchmesser - max.: 155 mmWerkstücklänge: 900 mmHub: 90 mmGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Werkstückdurchmesser - max.: 155 mm
Werkstücklänge: 900 mm
Hub: 90 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Werkstücklänge: 900 mm
Hub: 90 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
10
Woodworking machinerySawmills
Ausladung: 1800 mmWerkstückhöhe: 750 mmVerfahrweg: 4000 mmTischbreite: 5500 mmGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Ausladung: 1800 mm
Werkstückhöhe: 750 mm
Verfahrweg: 4000 mm
Tischbreite: 5500 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Werkstückhöhe: 750 mm
Verfahrweg: 4000 mm
Tischbreite: 5500 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
11
Plastic processing machinesCalender
Walzenbreite: 450 mmWalzendurchmesser - oben: 203 mmWalzendurchmesser - unten: 203 mmLeistung: 8,8 kw
Walzenbreite: 450 mm
Walzendurchmesser - oben: 203 mm
Walzendurchmesser - unten: 203 mm
Leistung: 8,8 kw
Walzendurchmesser - oben: 203 mm
Walzendurchmesser - unten: 203 mm
Leistung: 8,8 kw
6
Woodworking machineryMilling machinesOther
Tischgröße: . mmMotorleistung: 9 kWSpindeldurchmesser: . mmDrehzahl(en): U/minGewicht: kgBaujahr: 0
Tischgröße: . mm
Motorleistung: 9 kW
Spindeldurchmesser: . mm
Drehzahl(en): U/min
Gewicht: kg
Baujahr: 0
Motorleistung: 9 kW
Spindeldurchmesser: . mm
Drehzahl(en): U/min
Gewicht: kg
Baujahr: 0
10
Metal working and machine toolsSanding machinesDrill grinding machines
Bohrerdurchmesser: . mmBohrerlänge: . mmSpitzenwinkel: . °Gesamtleistungsbedarf: kWMaschinengewicht ca.: 0,8 tRaumbedarf ca.: 1,5x1x1,9 m
Bohrerdurchmesser: . mm
Bohrerlänge: . mm
Spitzenwinkel: . °
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: 0,8 t
Raumbedarf ca.: 1,5x1x1,9 m
Bohrerlänge: . mm
Spitzenwinkel: . °
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: 0,8 t
Raumbedarf ca.: 1,5x1x1,9 m
10
Metal working and machine toolsSheet metal working machinesPunching machines
Druck: 100 tHubzahl: 30-70 Hub/minStößelhub - max: 130 mmStößelverstellung: 100 mmTischfläche: 950x630 mmStößelfläche: 630x600 mmAusladung: 340 mmEinbauhöhe: 480 mmHaspel: GSWGesamtleistungsbedarf: kWMaschinengewicht ca.: 8,9 tRaumbedarf ca.: m
Druck: 100 t
Hubzahl: 30-70 Hub/min
Stößelhub - max: 130 mm
Stößelverstellung: 100 mm
Tischfläche: 950x630 mm
Stößelfläche: 630x600 mm
Ausladung: 340 mm
Einbauhöhe: 480 mm
Haspel: GSW
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: 8,9 t
Raumbedarf ca.: m
Hubzahl: 30-70 Hub/min
Stößelhub - max: 130 mm
Stößelverstellung: 100 mm
Tischfläche: 950x630 mm
Stößelfläche: 630x600 mm
Ausladung: 340 mm
Einbauhöhe: 480 mm
Haspel: GSW
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: 8,9 t
Raumbedarf ca.: m
9
Food machinesPharmaceutical and cosmetic machines
Behälter - Durchmesser max.: 2800 mmHöhe: 1500 mmInhalt: 7825 l
Behälter - Durchmesser max.: 2800 mm
Höhe: 1500 mm
Inhalt: 7825 l
Höhe: 1500 mm
Inhalt: 7825 l
5
Food machinesPharmaceutical and cosmetic machines
Wägebereich: 6000 kgBreite: 2500 mmTiefe: 1250 mm
Wägebereich: 6000 kg
Breite: 2500 mm
Tiefe: 1250 mm
Breite: 2500 mm
Tiefe: 1250 mm
5
Woodworking machineryExhaust systemsDeduster
Anschlußdurchmesser: 300 mmSaugleistung: 500 m³/hUnterdruck: paFilterfläche: m²
Anschlußdurchmesser: 300 mm
Saugleistung: 500 m³/h
Unterdruck: pa
Filterfläche: m²
Saugleistung: 500 m³/h
Unterdruck: pa
Filterfläche: m²
3
Metal working and machine toolsOther
Tischdurchmesser: 900 mmTischbelastung: 3000 kgEinbauhöhe: 580Hub: 95-800 mmGesamtleistungsbedarf: kWMaschinengewicht ca.: 8 tRaumbedarf ca.: m
Tischdurchmesser: 900 mm
Tischbelastung: 3000 kg
Einbauhöhe: 580
Hub: 95-800 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: 8 t
Raumbedarf ca.: m
Tischbelastung: 3000 kg
Einbauhöhe: 580
Hub: 95-800 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: 8 t
Raumbedarf ca.: m
10
Temperatur max.: . °Länge: 15000 mmBreite: 6000 mmHöhe: 5500 mmGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Temperatur max.: . °
Länge: 15000 mm
Breite: 6000 mm
Höhe: 5500 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Länge: 15000 mm
Breite: 6000 mm
Höhe: 5500 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
2
Commercial vehiclesOther
Anzahl der angetriebenen Achsen: 1Spurweite: 1435 mmZugkraft - max.: 300 tMotor: DeutzKraftstoffart: DieselMaschinengewicht ca.: tRaumbedarf ca.: m
Anzahl der angetriebenen Achsen: 1
Spurweite: 1435 mm
Zugkraft - max.: 300 t
Motor: Deutz
Kraftstoffart: Diesel
Maschinengewicht ca.: t
Raumbedarf ca.: m
Spurweite: 1435 mm
Zugkraft - max.: 300 t
Motor: Deutz
Kraftstoffart: Diesel
Maschinengewicht ca.: t
Raumbedarf ca.: m
10
Metal working and machine toolsSanding machinesOther
Schleiflänge: . mmSchleifbreite: . mmWerkstückhöhe: . mmGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Schleiflänge: . mm
Schleifbreite: . mm
Werkstückhöhe: . mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Schleifbreite: . mm
Werkstückhöhe: . mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
10
Metal working and machine toolsSanding machinesOther
Schleiflänge: . mmSchleifbreite: . mmWerkstückhöhe: . mmGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Schleiflänge: . mm
Schleifbreite: . mm
Werkstückhöhe: . mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Schleifbreite: . mm
Werkstückhöhe: . mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
10
Metal working and machine toolsMeasuring machinesPre-setting tools
Länge: 800 mmMessbereich X-Achse: 520 mmTischgröße: 700 mmGewicht: 900 kg
Länge: 800 mm
Messbereich X-Achse: 520 mm
Tischgröße: 700 mm
Gewicht: 900 kg
Messbereich X-Achse: 520 mm
Tischgröße: 700 mm
Gewicht: 900 kg
3
Metal working and machine toolsMeasuring machinesPre-setting tools
Werkzeugdurchmesser: 300 mmLänge: 300 mmGewicht: 80 kgAbmessung L-B-H: 800x400x750 mm
Werkzeugdurchmesser: 300 mm
Länge: 300 mm
Gewicht: 80 kg
Abmessung L-B-H: 800x400x750 mm
Länge: 300 mm
Gewicht: 80 kg
Abmessung L-B-H: 800x400x750 mm
10
Metal working and machine toolsMeasuring machinesPre-setting tools
Messbereich X-Achse: . mmMessbereich Y-Achse: . mmTischgröße: . mmWerkzeugdurchmesser: . mm
Messbereich X-Achse: . mm
Messbereich Y-Achse: . mm
Tischgröße: . mm
Werkzeugdurchmesser: . mm
Messbereich Y-Achse: . mm
Tischgröße: . mm
Werkzeugdurchmesser: . mm
6
Agricultural machineryTillage
Arbeitsbereich: 3 mZapfwellendrehzahl: . U/minAnzahl der Zinkenträger: . 0
Arbeitsbereich: 3 m
Zapfwellendrehzahl: . U/min
Anzahl der Zinkenträger: . 0
Zapfwellendrehzahl: . U/min
Anzahl der Zinkenträger: . 0
10
Metal working and machine toolsGear cutting machinesGear grinding machines
Raddurchmesser - max.: 1500 mmRadbreite: 550 mmModul - max.: 25Modul - min.: 2Werkstückgewicht max.: 6000 kgZähnezahl - max.: 432Zähnezahl - min.: 12Tischdurchmesser: 990 mmSchleifscheibe Abmessung: 400 mmGesamtleistungsbedarf: 75 kWMaschinengewicht ca.: 20,5 tRaumbedarf ca.: m
Raddurchmesser - max.: 1500 mm
Radbreite: 550 mm
Modul - max.: 25
Modul - min.: 2
Werkstückgewicht max.: 6000 kg
Zähnezahl - max.: 432
Zähnezahl - min.: 12
Tischdurchmesser: 990 mm
Schleifscheibe Abmessung: 400 mm
Gesamtleistungsbedarf: 75 kW
Maschinengewicht ca.: 20,5 t
Raumbedarf ca.: m
Radbreite: 550 mm
Modul - max.: 25
Modul - min.: 2
Werkstückgewicht max.: 6000 kg
Zähnezahl - max.: 432
Zähnezahl - min.: 12
Tischdurchmesser: 990 mm
Schleifscheibe Abmessung: 400 mm
Gesamtleistungsbedarf: 75 kW
Maschinengewicht ca.: 20,5 t
Raumbedarf ca.: m
6
Metal working and machine toolsGear cutting machinesGearwheel testing machines
Raddurchmesser - max.: 600 mmRadbreite: 150 mmModul - max.: 15Modul - min.: 1Einspannlänge min.: 45 mmEinspannlänge max.: 750 mmWerkstückgewicht: 150 kgGesamtleistungsbedarf: kWMaschinengewicht ca.: 0,55 tRaumbedarf ca.: 1,2x0,8x1,95 m
Raddurchmesser - max.: 600 mm
Radbreite: 150 mm
Modul - max.: 15
Modul - min.: 1
Einspannlänge min.: 45 mm
Einspannlänge max.: 750 mm
Werkstückgewicht: 150 kg
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: 0,55 t
Raumbedarf ca.: 1,2x0,8x1,95 m
Radbreite: 150 mm
Modul - max.: 15
Modul - min.: 1
Einspannlänge min.: 45 mm
Einspannlänge max.: 750 mm
Werkstückgewicht: 150 kg
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: 0,55 t
Raumbedarf ca.: 1,2x0,8x1,95 m
11
Metal working and machine toolsGear cutting machinesGear milling machines
Raddurchmesser - max.: 4400 mmRadbreite: 645 mmModul - max.: 35Steuerung: SiemensHauptantriebsmotor: 37 kWTischdurchmesser: 2500 mmSchrägungswinkel - max.: +/- 30 °Werkstückgewicht: 40000 kgGesamtleistungsbedarf: 142 kVAMaschinengewicht ca.: 75 tRaumbedarf ca.: m
Raddurchmesser - max.: 4400 mm
Radbreite: 645 mm
Modul - max.: 35
Steuerung: Siemens
Hauptantriebsmotor: 37 kW
Tischdurchmesser: 2500 mm
Schrägungswinkel - max.: +/- 30 °
Werkstückgewicht: 40000 kg
Gesamtleistungsbedarf: 142 kVA
Maschinengewicht ca.: 75 t
Raumbedarf ca.: m
Radbreite: 645 mm
Modul - max.: 35
Steuerung: Siemens
Hauptantriebsmotor: 37 kW
Tischdurchmesser: 2500 mm
Schrägungswinkel - max.: +/- 30 °
Werkstückgewicht: 40000 kg
Gesamtleistungsbedarf: 142 kVA
Maschinengewicht ca.: 75 t
Raumbedarf ca.: m
3
Metal working and machine toolsGear cutting machinesGear milling machines
Raddurchmesser - max.: 2000 mmRadbreite: . mmModul - max.: 22größter Fräserdurchmesser: 250 mmFräserdrehzahlen: 16-92 U/minGesamtleistungsbedarf: 13 kWMaschinengewicht ca.: tRaumbedarf ca.: m
Raddurchmesser - max.: 2000 mm
Radbreite: . mm
Modul - max.: 22
größter Fräserdurchmesser: 250 mm
Fräserdrehzahlen: 16-92 U/min
Gesamtleistungsbedarf: 13 kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Radbreite: . mm
Modul - max.: 22
größter Fräserdurchmesser: 250 mm
Fräserdrehzahlen: 16-92 U/min
Gesamtleistungsbedarf: 13 kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
10
Metal working and machine toolsAccessories and spare partsMeasuring technology
Länge: 2500 mmBreite: 1500 mmDicke: 300 mmGesamtleistungsbedarf: kWMaschinengewicht ca.: tRaumbedarf ca.: m
Länge: 2500 mm
Breite: 1500 mm
Dicke: 300 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m
Breite: 1500 mm
Dicke: 300 mm
Gesamtleistungsbedarf: kW
Maschinengewicht ca.: t
Raumbedarf ca.: m